1. Correct the compatible string for IPQ806x
2. Change the NAND controller and NAND chip nodes name
   for more clarity.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The FLASH_DEV_CMD registers starting offset is not same in
different QPIC NAND controller versions. This patch adds
the starting offset in NAND controller properties and uses
the same for calculating the actual offset of these registers.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

1. Add the data descriptor preparation function which will be used
   only by BAM DMA for forming the data SGL’s
2. Add clear BAM transaction and call it before every new request
3. Check DMA mode for ADM or BAM and call the appropriate
   descriptor formation function.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

1. DM_EN is only required for EBI2 NAND controller which uses ADM
2. BAM mode will be disabled after power on reset which needs to
   be enabled before starting any BAM transfers.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The NAND controller returns ECC failure during read of completely
erased codeword. The NAND controller has hardware functionality
to detect erased codeword in case of BCH ECC algorithm. The
NAND_ERASED_CW_DETECT_CFG register controls the erased
codeword/page detection controller. This register should be reset
before every page read by setting and clearing bit 0 of
NAND_ERASED_CW_DETECT_CFG.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

In EBI2, all codeword data will be read in FLASH_BUF_ACC buffer
and ADM will copy the data from source (FLASH_BUF_ACC) to
destination (memory for data read).

In QPIC, there is no FLASH_BUF_ACC and all the codeword data will
held in QPIC BAM FIFO buffers. It provides multiple READ_LOCATION
registers which will be used for copying the data from FIFO to
memory. The READ_LOCATION register will be used to read a
specific amount of data from a specific offset within the flash
buffer. It supports sequential offset requests. Each request is
composed of the following fields:

a. Offset within the flash buffer from which data should be
   read
b. Amount of data to be read
c. Flag bit specifying the last read request from the flash
   buffer. Following the last read request the NANDc refers to the
   buffer as empty.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The QPIC NAND BAM has multiple flags to control the transfer. This
patch adds flags parameter in register and data transfer DMA helper
functions and modifies all these functions call with appropriate
flags using following rule

1. Read and write can’t go in single command descriptor so
   separate SGL should be used.
2. For some of the requests, NWD flag should be set in BAM
   DMA descriptor.
3. For Data write, the BAM has internal buffer for each codeword.
   All write request will modify the data in internal buffer and
   this buffer will be flushed to NAND device once EOT flag is set.
   So for all the write requests in single codeword, the EOT should
   be cleared for all tx data descriptors except the last one.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

1. prepare_bam_async_desc is the function which will call
   all the DMA API’s. It will fetch the outstanding scatter gather
   list for passed channel and will do the DMA descriptor formation.
   The DMA flag is dependent upon the type of channel.

2. For ADM DMA, the descriptor is being formed for every DMA
   request so its sgl count will be always 1 while in BAM DMA, the
   clubbing of descriptor is being done to increase throughput.

3. ADM DMA uses only one channel while in BAM DMA, data descriptors
   will be submitted to tx channel (for write) or rx channel
   (for read) and all the registers read/write descriptors in
   command channel.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

- The BAM transaction is the core data structure which will be used
  for all the data transfers in QPIC NAND. Since the core framework
  in nand_base.c is serializing all the NAND requests so allocating
  BAM transaction before every transfer will be overhead. The memory
  for it be allocated during probe time and before every transfer,
  it will be cleared.

- The BAM transaction contains the array of
  command and data scatter gather list and indexes. For
  every transfer, all the resource will be taken from BAM
  transaction.

- The size of the buffer used for BAM transactions
  is calculated based on the NAND device with the maximum page size,
  among all the devices connected to the
  controller.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The EBI2 NAND controller directly remaps register read buffer with
dma_map_sg and DMA address of this buffer will be passed to DMA
API’s. While, on QPIC NAND controller, which uses BAM DMA, we read
the controller registers by preparing a BAM command descriptor. This
command descriptor requires the

  - controller register address
  - the DMA address in which we want to store the value read
    back from the controller register.

This command descriptor will be remapped with dma_map_sg
and its DMA address will be passed to DMA API’s. Therefore,
it's required that we also map our register read buffer for
DMA (using dma_map_single). We use the returned DMA address
for preparing entries in our command descriptor.

This patch adds the DMA mapping support for register read
buffer. This buffer will be DMA mapped during allocation
time. Before starting of any operation, this buffer will
be synced for device operation and after operation
completion, it will be synced again for CPU.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

1. QPIC NAND controller uses 3 BAM channels: command, data tx
   and data rx while EBI2 NAND controller uses only single ADM
   channel.
2. CRCI is only required for ADM DMA and it's not required for
   BAM DMA.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The current driver only supports EBI2 NAND controller which uses
ADM DMA. The latest QCOM SoC uses QPIC NAND controller with BAM
DMA. NAND registers and programming sequence are same for EBI2
and QPIC NAND so the same driver can support QPIC NAND also by
adding the BAM DMA support. This patch adds the is_bam in NAND
property which will be checked for determining the DMA engine type.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

Currently driver data is being assigned directly with ECC modes.
Now, the plan is to add more NAND controller versions which will
have different properties. This patch reorganizes the current driver
data assignment by creating NAND controller properties structure
which will contain all properties specific to NAND controller.
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The NAND page read fails without complete boot chain since
NAND_DEV_CMD_VLD value is not proper. The default power on reset
value for this register is

    0xe - ERASE_START_VALID | WRITE_START_VALID | READ_STOP_VALID

The READ_START_VALID should be enabled for sending PAGE_READ
command. READ_STOP_VALID should be cleared since normal NAND
page read does not require READ_STOP command.

Fixes: c76b78d8 ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

platform_get_irq() returns an error code, but the mtk_ecc driver
ignores it and always returns -EINVAL. This is not correct and,
prevents -EPROBE_DEFER from being propagated properly.

Print and propagate the return value of platform_get_irq on failure.

This issue was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

platform_get_irq() returns an error code, but the sh_flctl
driver ignores it and always returns -ENXIO. This is not correct
and, prevents -EPROBE_DEFER from being propagated properly.

Print and propagate the return value of platform_get_irq on failure.

This issue was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The return value of dma_map_single() should be checked by
dma_mapping_error(). However, in function flctl_dma_fifo0_transfer(), its
return value is checked against NULL, which could result in failures.
Signed-off-by: NPan Bian <bianpan2016@163.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

of_irq_get() may return 0 as well as negative error number on failure,
while the driver only checks for the negative values. The driver would
then call devm_request_irq() for IRQ0  in its probe method and never get
a valid interrupt.

Check for 'nc->irq <= 0' instead and return -ENXIO from the driver's probe
if of_irq_get() returned 0.

Fixes: f88fc122 ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NWenyou Yang <Wenyou.yang@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

According to the datasheet of the H27UCG8T2BTR the NAND Technology field
(6th byte of the "Device Identifier Description", bits 0-2) the
following values are possible:
- 0x0 = 48nm
- 0x1 = 41nm
- 0x2 = 32nm
- 0x3 = 26nm
- 0x4 = 20nm
- (all others are reserved)

Fix this by extending the mask for this field to allow detecting value
0x4 (20nm) as valid NAND technology.
Without this the detection of the ECC requirements fails, because the
code assumes that the device is a 48nm device (0x4 & 0x3 = 0x0) and
aborts with "Invalid ECC requirements" because it cannot map the "ECC
Level". Extending the mask makes the ECC requirement detection code
recognize this chip as <= 26nm and sets up the ECC step size and ECC
strength correctly.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Fixes: 78f3482d ("mtd: nand: hynix: Rework NAND ID decoding to extract more information")
Cc: <stable@vger.kernel.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

Commit a894cf6c ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
introduced a bug in the OOB layout description. Even if the driver claims
that 3 ECC bytes are reserved to protect 512 bytes of data, it's actually
5 ECC bytes to protect 512+6 bytes of data (some OOB bytes are also
protected using extra ECC bytes).

Fix the mxc_v1_ooblayout_{free,ecc}() functions to reflect this behavior.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Fixes: a894cf6c ("mtd: nand: mxc: switch to mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

Commit a53e35db ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Cyrille Pitchen <cyrille.pitchen@wedev4u.fr>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mtd@lists.infradead.org
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

- clk_prepare_enable() can fail here and we must check its return value.
 - stfsm_probe() can fail here and we must disable clock.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

- clk_prepare_enable() can fail here and we must check its return value.
 - oxnas_nand_probe() can fail here and we must disable clock.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

orion_nand_read_buf uses an inline assembly with the "ldrd"
instruction, which is only available from ARMv5 upwards. This
used to be fine, since all users have an ARMv5 or ARMv7 CPU,
but now we can also build a multiplatform kernel with ARMv4
support enabled in addition to the "kirkwood" (mvebu) platform.

This provides an alternative to call the readsl() function that
is supposed to have the same effect and is also optimized for
performance.

I first posted a version of this patch back in 2014, and there
was some discussion about it then. This fixes the bugs identified
back then and should be a reasonable alternative for the rare
corner case.

Link: https://patchwork.kernel.org/patch/4144791/
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The controller supported by the pxa3xx_nand driver is also available on
the mvebu 64-bit SoCs, such as the Armada 7K and Armada 8K SoCs. This
patch updates the Kconfig dependency to allow building the kernel for
this SoC family too.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The NAND controller can support multiple NAND devices having different
page sizes. Future code will require us to allocate memory based on the
maximum number of codewords among all the devices. We reorganize the
NAND device probing such that the ONFI parameters are first read for
each connected device to identify the maximum number of codewords
possible, and only then proceed with MTD device registration (i.e, call
nand_scan_tail and mtd_device_register).

This is a reorganization of the existing code and will not change any
functionality.
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The memset in clear_read_regs is overhead. All the register data
will be filled by DMA during NAND operation so making these
register variables zero is not required.
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

Each NAND page consist of multiple codewords. Following is
sequence for NAND page write according to hardware guide.

1. Program Power-up configuration, page row, page column
   address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
   codeword.
3. Read NAND_FLASH_STATUS for each codeword.

The step 1 should be done once for each page and step 2,3 should
be done for each codeword.

Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes page write functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

Each NAND page consist of multiple codewords. Following is
sequence for NAND page read according to hardware guide.

1. Program Power-up configuration, page row, page column
address and flash configuration registers.
2. Write NAND_FLASH_CMD followed by NANC_EXEC_CMD for each
codeword.
3. Read NAND_FLASH_STATUS for each codeword.

The step 1 should be done once for each page and step 2,3 should
be done for each codeword.

Currently, all the 3 steps are being done for each codeword which
is wrong. Now this patch reorganizes read page functions to
configure page specific register once and per codeword specific
registers for each NAND ECC step.
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

Currently the compatible “qcom,nandcs” is being used for each
connected NAND device to support for multiple NAND devices in the
same bus. The same thing can be achieved by looking reg property
for each sub nodes which contains the chip select number so this
patch removes the use of “qcom,nandcs” for specifying NAND device
sub nodes.

Since there is no user for this driver currently in so
changing compatible string is safe.
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

Currently the compatible “qcom,nandcs” is being used for each
connected NAND device to support for multiple NAND devices in the
same bus. The same thing can be achieved by looking reg property
for each sub nodes which contains the chip select number so this
patch removes the use of “qcom,nandcs” for specifying NAND device
sub nodes.

Since there is no user for this driver currently in so
changing compatible string is safe.
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The configuration for BCH is not correct in the current driver.
The ECC_CFG_ECC_DISABLE bit defines whether to enable or disable the
BCH ECC in which

	0x1 : BCH_DISABLED
	0x0 : BCH_ENABLED

But currently host->bch_enabled is being assigned to BCH_DISABLED.

Fixes: c76b78d8 ("mtd: nand: Qualcomm NAND controller driver")
Cc: stable@vger.kernel.org
Signed-off-by: NAbhishek Sahu <absahu@codeaurora.org>
Reviewed-by: NArchit Taneja <architt@codeaurora.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

pinctrl_pm_select_default_state() is already the default pinctrl state and
since pinctrl_pm_select_sleep_state() is not used in this driver, there
is no need to explicitly call pinctrl_pm_select_default_state().
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

This commit removes hard-coded '8' used for looping into
struct nand_chip.id.data array.

NAND_MAX_ID_LEN has been introduced by Artem Bityutskiy in
53552d22 for defining ids length in nand_flash_ids[] list.

This commit unifies ids length in nand base driver.
Signed-off-by: NJean-Louis Thekekara <jeanlouis.thekekara@parrot.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

The nand_scan_ident() function is not expected to allocate resources,
and people are usually not calling nand_cleanup() if something fails
between nand_scan_ident() and nand_scan_tail().

Move all functions that may allocate resource to the nand_scan_tail()
path to prevent such resource leaks.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>

Commit 7d70f334 ("mtd: nand: add lock/unlock routines") introduced
support for the Micron LOCK/UNLOCK commands but no one ever used the
nand_lock/unlock() functions.

Remove support for these vendor-specific operations from the core. If
one ever wants to add them back they should be put in nand_micron.c and
mtd->_lock/_unlock should be directly assigned from there instead of
exporting the functions.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>