Before this patch, the following error would sometimes occur after a
resume on pxa3xx:

    /path/to/mm/memory.c:144: bad pmd 8040542e.

The problem was that a temporary page table mapping was being improperly
restored.

The PXA3xx resume code creates a temporary mapping of resume_turn_on_mmu
to avoid a prefetch abort.  The pxa3xx_resume_after_mmu code requires
that the r1 register holding the address of this mapping not be
modified, however, resume_turn_on_mmu does modify it. It is mostly
correct in that r1 receives the base table address, but it may also
get other bits in 13:0.  This results in pxa3xx_resume_after_mmu
restoring the original mapping to the wrong place, corrupting memory
and leaving the temporary mapping in place.
Signed-off-by: NMatt Reimer <mreimer@sdgsystems.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

XSCALE_CACHE_ERRATA doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: NChristoph Egger <siccegge@cs.fau.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The remaining registers are separated into:

   - <mach/regs-ost.h>
   - <mach/regs-rtc.h>
   - <mach/regs-intc.h>

and then we can remove pxa-regs.h completely. Instead of #include this
file, let's:

1. include the specific <mach/regs-*.h> with care (if that's absolutely
   necessary)

2. define the registers in the driver, make cleanly defined API to expose
   the register access to external with sufficient reason
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This just leaves include/asm-arm/plat-* to deal with.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove includes of asm/hardware.h in addition to asm/arch/hardware.h.
Then, since asm/hardware.h only exists to include asm/arch/hardware.h,
update everything to directly include asm/arch/hardware.h and remove
asm/hardware.h.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. clear RDH bit after resuming back from D3, otherwise, the multi function
   pins will retain the low power state

2. save/restore essential system registers
Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There's no point building standby/sleep code for processors which
aren't configured.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

PXA3 has a different memory controller from PXA2 platforms.  Avoid
clashing definitions by moving the PXA2 definitions to pxa2xx-regs.h
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

r2 is not guaranteed to be preserved over a function call, so relying
on it to store the link register over the call to sleep_phys_sp() is
unreliable.  Store the link register on the stack instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

1. split pxa_cpu_suspend to pxa25x_cpu_suspend and pxa27x_cpu_suspend
   and make pxa25x_cpu_pm_enter() and pxa27x_cpu_pm_enter() to invoke
   the corresponding _suspend functions, thus remove all those ugly
   #ifdef .. #endif out of sleep.S

2. move the declarations of those suspend functions to pm.h

note: this is not a clean enough solution until all the pxa25x and
pxa27x specific part is further removed out of sleep.S, sleep.S is
supposed to contain generic code only
Signed-off-by: Neric miao <eric.y.miao@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

DEFAULT_FIQ was entirely unused.  MODE_* are just redefinitions
of *_MODE.  Use *_MODE instead.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Todd Poynor

Add symbols for PXA2xx PWRMODE register M field that selects low-power
mode, replace unadorned constants.  Honor power mode parameter of
pxa_cpu_suspend(mode), no longer force to 3 (sleep).  Full Deep Sleep
low-power mode support for PXA27x is pending generic PM interfaces to
select more than 2 suspend-to-RAM-style power modes, but this is
expected soon. This can be hardcoded in the meantime by replacing the
pxa_cpu_suspend() parameter value.  From David Burrage and Todd Poynor.
Try #2 removes one of the register copies and moves the code to save the
pxa_cpu_suspend parameter to immediately surround the call that requires
the parameter value be preserved.
Signed-off-by: NTodd Poynor <tpoynor@mvista.com>
Signed-off-by: NNicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch from Jeff Lackey

This patch updates arch/arm/mach-pxa/sleep.S to support
the PXA270 CPU.  It works around Errata 39 & 50 from the
Intel(R) PXA27x Processor Family Specification Update.

Signed-off-by: Jeff Lackey
Signed-off-by: Russell King

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!