twl4030-madc driver can only handle twl4030 class MADC. The newer revisions
of twl does not have MADC, instead they have different IP called GPADC which
is not backward compatible.
Acked-by: NTero Kristo <t-kristo@ti.com>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Retu is a multi-function device found on Nokia Internet Tablets
implementing at least watchdog, RTC, headset detection and power button
functionality.

This patch implements minimum functionality providing register access,
IRQ handling and power off functions.
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

linux/err.h was included twice.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

They contain documented status readback fields.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Set tps65217 PMIC status to OFF if power enable toggle is supported.
By setting this bit to 1 to enter PMIC to OFF state when PWR_EN pin
is pulled low. Also adds a DT flag to specify that device pmic
supports shutdown control or not.
Signed-off-by: NColin Foe-Parker <colin.foeparker@logicpd.com>
[anilkumar@ti.com: move the additions to tps65217 MFD driver]
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This fixes the following build error on some architectures (parisc at least):

drivers/mmc/host/rtsx_pci_sdmmc.c: In function 'sd_normal_rw':
drivers/mmc/host/rtsx_pci_sdmmc.c:448:2: error: implicit
declaration of function 'kzalloc'
[-Werror=implicit-function-declaration]
drivers/mmc/host/rtsx_pci_sdmmc.c:448:6: warning: assignment
makes pointer from integer without a cast [enabled by default]
drivers/mmc/host/rtsx_pci_sdmmc.c:472:2: error: implicit
declaration of function 'kfree'
[-Werror=implicit-function-declaration]
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Acked-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

For Realtek card reader, internal regsiter SD_CFG2 should be configured
before transferring data.
The default value of SD_CFG2 is proper for writing data. But for reading
sequence, the timing is not good enough. So in some extreme circumstance,
card reader may sample the response data from the card as good even if
the data is wrong. And this will cause the bad consequence.
In the prior version, the value of this register has been calculated,
but forgotten to write back to the internal register.
Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Acked-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the regmap irq framework for implementing TPS65090 interrupt
support in place of implementing it locally.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Since tps65090 register is accessed via regmap, moving
the register access APIs to header and making it as inline.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Remove unused member from tps65090 data structure as
these are not used.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add error prints when memory allocation failed for
tps65090 data. Also cleanups the melloc arguments.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

TPS65090 supports the battery charging and hence adding
the device name in the list of TPS65090 children. Also
remove the tps65090-regulator as it duplicates with
tps65090-pmic for regulator driver.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

TPS80031/ TPS80032 Fully Integrated Power Management with Power
Path and Battery Charger. The device provides five configurable
step-down converters, 11 general purpose LDOs, USB OTG Module,
ADC, RTC, 2 PWM, System Voltage Regulator/Battery Charger with
Power Path from USB, 32K clock generator.

Add the mfd core driver for TPS80031/TPS80032.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The DSP memories are mapped into the register map, make them readable and
writable by updating max_register appropriately.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

These are required for the clock infrastructure code to properly configure
and control the sta2x11 PLLs.
Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The lock is used to implement atomic operations on each platform
device's registers, so it looks reasonable having one lock per
device instead of one common lock for all the devices belonging
to the same sta2x11 instance.
Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The gpio platform driver will take care of its platform data,
let's not do any checks here.
Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The pci probe method is called twice now, so we have to call
sta2x11_mfd_add() only once to avoid a -EBUSY error.
Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Since there are now many sta2x11-mfd platform devices, using defines
for their names looks like a better solution.
Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

A couple of predefined clocks (mux and gated) need to be
initialized with the virtual address of the clock's controlling
register and the address of a spinlock used to protect against
races.

This function exports such data for all the mfd cells.
Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

A driver for the apb-soc registers is needed by the clock
infrastructure code to configure and control clocks on the sta2x11
chip.

Since some of the functions in sta2x11-mfd.c were almost identical
for the two existing platform devices, the following changes
have been performed to avoid further code duplication while
adding the apb-soc-regs driver:

* The sctl_regs and apbreg_regs fields in struct sta2x11_mfd
have been turned into just one array of pointers accessed by
device index.
* Platform probe methods have become one-liners invoking a
common probe with the device's index as second parameter.
* For loops have been inserted where the same operations
were performed for each of the two bars of a pci device.
* The apbreg_mask and sctl_mask functions were almost identical,
so they were turned into inline functions invoking a common
__sta2x11_mfd_mask() with the platform device's index as last
parameter. To do this, enum sta2x11_mfd_plat_dev has been declared in
sta2x11-mfd.h and more device types have been added to it.
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Acked-by: NAlessandro Rubini <rubini@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds the mfd cell to use the adc part of the Nano River Technologies
viperboard.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Reviewed-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NJonathan Cameron <jic23@kernel.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds the mfd cell to use the i2c part of the Nano River Technologies
viperboard as i2c master.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This adds the mfd cell to use the gpio a and gpio b part
of the Nano River Technologies viperboard.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add mfd driver for Nano River Technologies viperboard.
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

mfd_remove_devices would iterate over all devices sharing a parent with
an mfd device regardless of whether they were allocated by the mfd core
or not. This especially caused problems when the device structure was
not contained within a platform_device, because to_platform_device is
used on each device pointer.

This patch defines a device_type for mfd devices and checks this is
present from mfd_remove_devices_fn before processing the device.

Cc: stable@vger.kernel.org
Signed-off-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Tested-by: NPeter Tyser <ptyser@xes-inc.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Convert to the new da9052 interrupt functions, so that we can get rid of
irq_base references.

Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Convert to the new da9052 interrupt functions, so that we can get rid of
irq_base references.
Acked-by: NAnton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the new da9052 irq functions and allow the driver to probe successfully.

Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: <linux-input@vger.kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Currently da9062_tsi does not probe and it fails as follows:

da9052 1-0048: Unable to determine device interrupts

Use the new da9052 irq functions and allow the driver to probe and operate
correctly.

Tested on mx53qsb board using 'evtest' tool.

Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: <linux-input@vger.kernel.org>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Create a da9052-irq.c file so that it can handle interrupt related functions.

This is useful for allowing the da9052 drivers to use such functions
when dealing with da9052 interrupts.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

On a mx53qsb dt-kernel the da9052-core driver fails to probe as follows:

da9052 1-0048: DA9052 ADC IRQ failed ret=-22

The reason for the error was due to passing only the offset as the interrupt
number in request_threaded_irq() without da9052->irq_base.

The recommended approach though is to use regmap_get_virq() to acquire the
interrupt number and this allows to get rid of da9052->irq_base.

Fix it and allow the driver to probe successfully.

Also provide a few more error logs and change the irq string to "adc-irq", so
that it appears as a single word in 'cat /proc/interrupts'
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviwed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

When adding the sub device "tps65910-rtc", is it passed the
IO resource IRQ for the interrupt number. This interrupt needs
to map in the device irq domain. Pass the irq domain of device
in mfd_add_devices() so that proper irq mapping can be done when
adding the sub device RTC.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

In place of implementing the irq support in separate file,
moving implementation to main mfd file.
The irq files only contains the table and init steps only
and does not need extra file to have this only for this
purpose.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Implement irq support of tps65910 with regmap irq framework
in place of implementing locally.
This reduces the code size significantly and easy to maintain.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>