This patch adds sunxi sata support to A10 boards that have such a connector.
Some boards also feature a regulator via a GPIO and support for this is also
added.
Signed-off-by: NOlliver Schinagl <oliver@schinagl.nl>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Most sunxi boards with a sata connector also have a gpio controlled connector
for sata target power and almost all sunxi boards have a gpio controlled vbus
for usb1 and usb2.

This commit adds an include file for the regulators representing these
supplies, avoiding the need to copy and paste the regulator code to allmost
all sunxi board dts files.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The module 0 clock compatibles were changed between the time the patch was sent
and it was merged. Update the compatibles.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A20-Olinuxino-micro has two SPI bus exposed on its UEXT connectors, enable
them.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A13 has 3 SPI controllers compatible with the one found in the A10. Add
them in the DT.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A10s has 3 SPI controllers compatible with the one found in the A10. Add
them in the DT.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A10 has 4 SPI controllers that are now supported. Add them in the DT.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A20 has 4 SPI controllers compatible with the one found in the A10. Add
them in the DT.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

According to Documentation/devicetree/bindings/regulator/regulator.txt
regulator nodes should not be placed under 'simple-bus'.

Mark Rutland also explains about it at:
http://www.spinics.net/lists/linux-usb/msg101497.htmlSigned-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Switch the device tree to the new compatibles introduced in the clock drivers
to have a common pattern accross all Allwinner SoCs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A20 SoC is built around a pair of Cortex-A7 cores,
which have the usual generic timers. Report this in the DT.
Signed-off-by: NMarc Zyngier <marc.zyngier@arm.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NRoman Byshko <rbyshko@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NRoman Byshko <rbyshko@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NRoman Byshko <rbyshko@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

All Allwinner A20 boards we support can only use either EMAC or GMAC,
as they share the same pins. As we have switched all supported to
GMAC, we should alias GMAC (the active controller) as ethernet0,
so u-boot will insert the MAC address for the correct controller.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The CubieTruck uses the GMAC with an RGMII phy.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A20 has EMAC and GMAC muxed on the same pins.
Add pin sets with gmac function for MII and RGMII mode to the DTSI.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The GMAC uses 1 of 2 sources for its transmit clock, depending on the
PHY interface mode. Add both sources as dummy clocks, and as parents
to the GMAC clock node.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Device tree naming conventions state that node names should match
node function. Change fully functioning clock nodes to match and
add clock-output-names to all sunxi clock nodes.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A31 has 4 SPI controllers. Add them in the DTSI.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The module clocks in the A31 are still compatible with the A10 one. Add the SPI
module clocks and the PLL6 in the device tree to allow their use by the SPI
controllers.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

UART2 is used on CubieTruck to connect to the Bluetooth module.
Add the pin set used in this case.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This patch will add a basic board support DT for the
LinkSprite pcDuino board.
Signed-off-by: NZoltan HERPAI <wigyori@uid0.hu>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Some UART aliases have been defined, but not all of them. Add the remaining
ones to be consistent and to ease the parsing of the DT by the bootloaders.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

TI_EDMA fell out of automatically selected options in the multi_v7
defconfig due to a select being removed from the davinci Kconfig entry. So
we need to re-enable explicitly to not regress some platforms.

The rest is just the result of running 'make multi_v7_defconfig + make
savedefconfig' to remove entries that are no longer needed due to changed
dependencies/selects or defaults.
Signed-off-by: NOlof Johansson <olof@lixom.net>

Recent boot farm testing has highlighted some issues with mvebu and
multiplatform kernels.  Increase the test coverage so we can discover
these issues earlier.
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The board schematic states that the "SD_CARD_DET_N gets pulled to GND
when card is inserted" so the polarity has been updated to active low.

Polarity is now specified with a GPIO define instead of a magic number.
Signed-off-by: NTim Kryger <tim.kryger@linaro.org>
Reviewed-by: NMatt Porter <matt.porter@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Select CONFIG_AT803X_PHY so that we can boot hummingboard via NFS.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Drop automatic selection of TI_EDMA from Keystone Kconfig file,
as it produces build warning in case if CONFIG_DMADEVICES is not set:

warning: (ARCH_KEYSTONE) selects TI_EDMA which has unmet direct dependencies (DMADEVICES && (ARCH_DAVINCI || ARCH_OMAP || ARCH_KEYSTONE))

Instead enable TI EDMA support from defconfig.
Reported-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>