Enable the dwmac-sun8i ethernet driver as a module in the ARM64 defconfig.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the dwmac-sun8i driver in the multi_v7 default configuration
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enable the dwmac-sun8i driver in the sunxi default configuration
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i  hardware is present on the BananaPi M64.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the pine64 plus.
It uses an external PHY rtl8211e via RGMII.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the pine64
It uses an external PHY via RMII.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i is an Ethernet MAC that supports 10/100/1000 Mbit
connections. It is very similar to the device found in the Allwinner
H3, but lacks the internal 100 Mbit PHY and its associated control
bits.
This adds the necessary bits to the Allwinner A64 SoC .dtsi, but keeps
it disabled at this level.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the dt node for the syscon register present on the
Allwinner A64.

Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the NanoPi Neo.
It uses the internal PHY.
This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On the Orange Pi PC Plus, the polarity of the LEDs on the RJ45 Ethernet
port were changed from active low to active high.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the Orange PI 2.
It uses the internal PHY.

This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the Orange PI One.
It uses the internal PHY.

This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the Orange PI Zero.
It uses the internal PHY.

This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i hardware is present on the Orange PI PC.
It uses the internal PHY.

This patch create the needed emac node.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i is an ethernet MAC hardware that support 10/100/1000
speed.

This patch enable the dwmac-sun8i on Allwinner H3/H5 SoC Device-tree.
SoC H3/H5 have an internal PHY, so optionals syscon and ephy are set.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the dt node for the syscon register present on the
Allwinner H3/H5

Only two register are present in this syscon and the only one useful is
the one dedicated to EMAC clock..
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The dwmac-sun8i is a heavy hacked version of stmmac hardware by
allwinner.
In fact the only common part is the descriptor management and the first
register function.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds documentation for Device-Tree bindings for the
syscon present in allwinner devices.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds documentation for Device-Tree bindings for the
Allwinner dwmac-sun8i driver.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of adding more ifthen logic for adding a new mac_device_info
setup function, it is easier to add a function pointer to the function
needed.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thoses symbol will be needed for the dwmac-sun8i ethernet driver.
For letting it to be build as module, they need to be exported.
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

asm-generic/socket.h already has an exception for the differences that
powerpc needs, so just include it after defining the differences.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add callback to the ethtool flash_device op. This callback uses the mlxfw
module to flash the new firmware file to the device.

As the firmware flash process takes about 20 seconds and ethtool takes the
rtnl lock during the flash_device callback, release the rtnl lock at the
beginning of the flash process and take it again before leaving the
callback. This way, the rtnl is not held during the process. To make sure
the device does not get deleted during the flash process, take a reference
to it before releasing the rtnl lock.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yuval Mintz says:

====================
qed: Status block changes

The device maintains a CAM mapping of the internal status blocks
and the various PF/VF MSI-x vector mappings.
During initialization, the driver reads the HW memory and constructs
a shadow SW implementation which it would later use for manipulation
of interrupts. E.g., when enabling VFs and setting their MSI-x tables.

The driver currently has some very strict assumptions on the order the
entries are placed in the CAM. Specifically, it assumes that all entries
belonging to a PF would be consecutive and in-order in the CAM, and that
the VF entries would then follow. But there's no actual HW constraint
enforcing this assumption [although management firmware does set it
accordingly to same assumption initially].

Since the CAM is re-configurable, there are now SW flows employeed
by other OSes that might cause the assumption to be invalid.
Such flows allow the PF to forfeit some of it's available interrupts
in favor of its VFs or vice versa.
While those are not employeed today by qed, we want to relax the
assumptions as much as we can -
both to allow functionality after PDA as well as allowing future
compatibility where the driver would be loaded after a newer one has
'dirtied' the CAM configuration.

In addition to patches meant for the above relaxation, the series
also contains various cleanups & refactoring for interrupt logic
[most of which is !semantic].
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we're resetting the IGU CAM each time we initialize the PF
device, there's no need to reset the VF SBs again when initializing
IOV.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IGU CAM contains an assocaition between hardware SBs
and interrupt lines, and it can be dynamically configured
to allow more interrupts in one entity over another, specifically
for Re-distibution of SBs between a PF and its child VFs.

While we don't yet use this functionality, there are other
clients that do and as such its possible the information
passed from management firmware during initialization in
regard to the possible number of SBs doesn't accurately reflect
the current HW configuration.

The following changes are going to apply to the driver init sequence:

 a. PF is going to re-configure all entries belonging to itself and
    its child VFs in IGU CAM based on the management firmware info
    regarding the number of SBs that are supposed to exist there.

 b. PF is going to stop using the SB resource [management firmware
    provided information] for anything but the initialization.
    Instead, it would use the live-time counters it maintains for
    the numbers.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A PF today holds 2 different arrays - one holding information
about the HW configuration and one holding information about
the SBs that are used by the protocol drivers.
These arrays aren't really connected - e.g., protocol driver
initializing a given SB would not mark the same SB as occupied
in the HW shadow array.

Move into a single array [at least for PFs] - hold the mapping
of the driver-protocol SBs on the HW entry which they configure.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IOV code is very intrusive in its manipulation of the status block
database.
Add a new auxiliary function to allow the PF to find an available unused
status block to configure for a specific VF's MSI-x vector.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current code assumes there's a known layout for SBs in the IGU,
where all the SBs of a single entity would be laid in consecutive
order of vectors.

While the assumption is still kept by management firmware, we already
have the necessary information to eliminate it, so no reason to keep
it in code.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already have an API struct that contains interrupt-related
numbers. Use it to encapsulate all information relating to the
status of SBs as (used|free).
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An additional step for relaxing the IGU order assumption, we now add
an auxiliary function that can be used for finding the HW status block
that's associated with a given MSI-x vector.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In qed code, sb_id means 2 different things:
  - An interrupt vector [usually when received as a parameter from
    a protocol driver, but not only] that's associated with a status
    block.

  - An index to a status block entity existing in HW.

This patch renames the references to the HW entity, adding an 'igu_'
prefix to allow an easier distinction.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a first step for relaxing various assumptions done by driver
about the IGU mapping, the driver is now going to read the entire
IGU into a shadow copy, and mark in its database each status block
that's relevant for it.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Separate the portions controlling interrupt enablement form those
controlling the ability of HW to generate attentions.
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

function ksz_rcv can be made static as it does not need to be
in global scope. Reformat arguments to make it checkpatch warning
free too.

Cleans up sparse warning: "symbol 'ksz_rcv' was not declared. Should
it be static?"
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NWoojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the commit 55454a56 ("ppp: avoid dealock on recursive xmit"),
the PPP xmit path is protected by wrapper functions which disable the
bh already. So it is unnecessary to disable the bh again in the real
xmit path.
Signed-off-by: NGao Feng <gfree.wind@vip.163.com>
Acked-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

recent updates to inet_rtm_getroute dropped skb_dst_set in
inet_rtm_getroute. This patch restores it because it is
needed to release the dst correctly.

Fixes: 3765d35e ("net: ipv4: Convert inet_rtm_getroute to rcu versions of route lookup")
Reported-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Woojung Huh says:

====================
dsa: add Microchip KSZ9477 DSA driver

This series of patches is for Microchip KSZ9477 DSA driver.
KSZ9477 is 7 ports GigE switch with numerous advanced features.
5 ports are 10/100/1000 Mbps internal PHYs and 2 ports have
Interfaces to SGMII, RGMII, MII or RMII.

This patch supports VLAN, MDB, FDB and port mirroring offloads.

Welcome reviews and comments from community.

Note: Tests are performed on internal development board.

V5
- add missing MODULE_LICENSE

V4
- update per review comments
- cosmetic changes
- net/dsa/tag_ksz.c
  * skb_put() & memset() are changed to skb_put_padto()
- drivers/net/dsa/microchip/ksz_common.
   * vlan access mutex is updated
   * mib_names[] is changed to static const

V3
- update per review comments
- cosmetic changes
- drivers/net/dsa/microchip/ksz_common.c
  * clean up ksz_switch_chips[]
  * consolidate checking loops into functions
  * update mutex for better locking
  * replace devm_kmalloc_array() to devm_kcalloc()
- MAINTAINERS
  * add missing net/dsa/tag_ksz.c

V2
- update per review comments
- several cosmetic changes
- net/dsa/tag_ksz.c
  * constants are changed to defines
  * remove skb_linearize() in ksz_rcv()
  * ksz_xmit()checks skb tailroom before allocate new skb
- drivers/net/phy/micrel.c
  * remove PHY_HAS_MAGICANEG from ksphy_driver[]
- drivers/net/dsa/microchip/ksz_common.c
  * add timeout to avoid endless loop
  * port initialization is move to ksz_port_enable() instead of  ksz_setup_ports()
- Documentation/devicetree/bindings/net/dsa/ksz.txt
  * fix typo and indentations
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>