This patch adds CONFIG_ARCH_EXYNOS5 and CONFIG_SOC_EXYNOS5250
for supporting EXYNOS5250 SoC and allows supporting EXYNOS4
and EXYNOS5 together.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The EXYNOS5250 has two Cortex-A15 cores and there's no
need to call scu_enable() in platform_smp_prepare_cpus()
because Cortex-A15 has no regarding scu register which
can be used for getting number of cores.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The GPIOs of EXYNOS4 and EXYNOS5 are changed to use
ioremap instead of static mapping. It alse causes the
change of external interrupt IO mapping. This patch
changes EXYNOS4 to EXYNOS for common use and changes
EINT_x macros for supporting dynamic IO mapping.
Signed-off-by: NEunki Kim <eunki_kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds the interrupt definitions for EXYNOS5250 at
<mach/irqs.h> file and it is needed for EXYNOS5250 SoC.
As a note, for single zImage of EXYNOS4 and EXYNOS5, prefix
of EXYNOS4_ and EXYNOS5_ has been added.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch add support for EXYNOS5250 SoC has two Cortex-A15 cores.
Since actually, most codes in mach-exynos/ are used commonly for
EXYNOS4 and EXYNOS5 the EXYNOS5/EXYNOS5250 has been implemented
in mach-exynos/.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Actually, the base address of uart is different between EXYNOS4
and EXYNOS5 and this patch enables to support uart for EXYNOS4
and EXYNOS5 SoCs at runtime.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

In all of Samsung platform, the setup-i2c0.c file for I2C channel 0
is always compiled. So when supporting new SoC,it should be updated
for it. Since EXYNOS5 GPIO will be supported after this, there is no
setup gpio in there now. It will be implemented with that, of course.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds clock-exynos5.c for EXYNOS5250 now
and that can be used for other EXYNOS5 SoCs later.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Since exynos4_init_uarts() can be used for EXYNOS5 SoCs,
this patch changes the name of function to exynos_init_uarts().
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

According to commit cc511b8d ("ARM: 7257/1: EXYNOS: introduce
arch/arm/mach-exynos/common.[ch]"), we don't need to declare extern
for exynos4_map_io(), exynos4_init_clocks(), exynos4_init_uarts(),
and exynos_init(). And the exynos4210_register_clocks() and
exynos4212_register_clocks depend on each SoC not ARCH_EXYNOS4.
So this patch fixed above.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

The framebuffer driver needs the clock named 'lcd' as its bus
clock but the equivalent clock on Exynos4 is named as 'fimd'.
Hence, create a clkdev lookup entry with the name 'lcd' that
references the 'fimd' clock.
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Acked-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
[kgene.kim@samsung.com: rebased on top of latest samsung tree]
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NBoojin Kim <boojin.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Amba core assumes the pclk to be named as apb_pclk. During device probe,
it tries to get that clock and enable that. When PM_RUNTIME is enabled,
dma clock is not explicitly enabled in pl330_probe, which causes device
probe to fail. Adding a clkdev entry for apb_pclk for mdma1 fixes the
problem.

This patch fixes following runtime error.

dma-pl330 dma-pl330.2: PERIPH_ID 0x0, PCELL_ID 0x0 !
dma-pl330: probe of dma-pl330.2 failed with error -22
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch adds MDMA platform data and enables
MDMA for DMA memcpy operation for EXYNOS SoCs.
Signed-off-by: NBoojin Kim <boojin.kim@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

EXYNOS4212/4412 memory bus devfreq driver requires some register
addresses that were not defined with EXYNOS4210 support.
This patch adds the required register addresses and shift/mask data.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Signed-off-by: NJaecheol Lee <jc.lee@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

In the commit, "PM / devfreq: update the name of EXYNOS clock register"
ommitted one register.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

According to replacing the name of EXYNOS clock registers,
this patch updates exynos4_bus.c file where it is used.
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch changes prefix of the clk register from S5P_ to
EXYNOS4_ for new EXYNOS SoCs such as EXYNOS5 and adds prefix
exynos4_ on clk declarations.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch uses static declaration struct which is not
used in other file and re-arrange with group in header
file.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This patch changes the name of clock.c to clock-exynos4.c for other
EXYNOS series such as EXYNOS5. And since the header file of clock
is used only in arch/arm/mach-exynos, moves it in the local directory.
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

Conflicts:
	arch/arm/mach-exynos/dma.c
	arch/arm/mach-s5p64x0/dma.c
	arch/arm/mach-s5pc100/dma.c
	arch/arm/mach-s5pv210/dma.c

SCSI fixes from James Bottomley:
 "There's just a single fix in here: the osd max device number fix."

* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] osd_uld: Bump MAX_OSD_DEVICES from 64 to 1,048,576

PARISC fixes from James Bottomley:
 "This is a set of build fixes to get the cross compiled architecture
  testbeds building again"

* tag 'parisc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/parisc-2.6:
  [PARISC] don't unconditionally override CROSS_COMPILE for 64 bit.
  [PARISC] include <linux/prefetch.h> in drivers/parisc/iommu-helpers.h
  [PARISC] fix compile break caused by iomap: make IOPORT/PCI mapping functions conditional

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf/x86/kvm: Fix Host-Only/Guest-Only counting with SVM disabled

Pull from Herbert Xu:
  "This push fixes a bug in mv_cesa that causes all hash operations
   that supply data on a final operation to fail."

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: mv_cesa - fix final callback not ignoring input data

Commit 5707c87f "vfs: uninline full_name_hash()" broke the modular
build, because it needs exporting now that it isn't inlined any more.
Reported-by: NTetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

hhwmon fixes for 3.3-rc6 from Guenter Roeck:

These patches are necessary for correct operation and management of
F75387.

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (f75375s) Catch some attempts to write to r/o registers
  hwmon: (f75375s) Properly map the F75387 automatic modes to pwm_enable
  hwmon: (f75375s) Make pwm*_mode writable for the F75387
  hwmon: (f75375s) Fix writes to the pwm* attribute for the F75387

fbdev fixes for 3.3 from Florian Tobias Schandinat

It includes:
 - two fixes for OMAP HDMI
 - one fix to make new OMAP functions behave as they are supposed to
 - one Kconfig dependency fix
 - two fixes for viafb for modesetting on VX900 hardware

* tag 'fbdev-fixes-for-3.3-2' of git://github.com/schandinat/linux-2.6:
  OMAPDSS: APPLY: make ovl_enable/disable synchronous
  OMAPDSS: panel-dvi: Add Kconfig dependency on I2C
  viafb: fix IGA1 modesetting on VX900
  viafb: select HW scaling on VX900 for IGA2
  OMAPDSS: HDMI: hot plug detect fix
  OMAPDSS: HACK: Ensure DSS clock domain gets out of idle when HDMI is enabled

sound fixes for 3.3-rc6 from Takashi Iwai

This contains again regression fixes for various HD-audio and ASoC
regarding SSI and dapm shutdown path.  In addition, a minor azt3328
fix and the correction of the new jack-notification strings in HD-audio.

* tag 'sound-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: hda - Kill hyphenated names
  ALSA: hda - Add a fake mute feature
  ALSA: hda - Always set HP pin in unsol handler for STAC/IDT codecs
  ALSA: azt3328 - Fix NULL ptr dereference on cards without OPL3
  ALSA: hda/realtek - Fix resume of multiple input sources
  ASoC: i.MX SSI: Fix DSP_A format.
  ASoC: dapm: Check for bias level when powering down

The code in link_path_walk() that finds out the length and the hash of
the next path component is some of the hottest code in the kernel.  And
I have a version of it that does things at the full width of the CPU
wordsize at a time, but that means that we *really* want to split it up
into a separate helper function.

So this re-organizes the code a bit and splits the hashing part into a
helper function called "hash_name()".  It returns the length of the
pathname component, while at the same time computing and writing the
hash to the appropriate location.

The code generation is slightly changed by this patch, but generally for
the better - and the added abstraction actually makes the code easier to
read too.  And the new interface is well suited for replacing just the
"hash_name()" function with alternative implementations.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It did some odd things for unclear reasons.  As this is one of the
functions that gets changed when doing word-at-a-time compares, this is
yet another of the "don't change any semantics, but clean things up so
that subsequent patches don't get obscured by the cleanups".
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

.. and also use it in lookup_one_len() rather than open-coding it.

There aren't any performance-critical users, so inlining it is silly.
But it wouldn't matter if it wasn't for the fact that the word-at-a-time
dentry name patches want to conditionally replace the function, and
uninlining it sets the stage for that.

So again, this is a preparatory patch that doesn't change any semantics,
and only prepares for a much cleaner and testable word-at-a-time dentry
name accessor patch.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

These don't change any semantics, but they clean up the code a bit and
mark some arguments appropriately 'const'.

They came up as I was doing the word-at-a-time dcache name accessor
code, and cleaning this up now allows me to send out a smaller relevant
interesting patch for the experimental stuff.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It makes no sense to attempt to manually configure the fan in auto mode,
or set the duty cycle directly in closed loop mode.  The corresponding
registers are then read-only.  If the user tries it nonetheless, error out
with EINVAL instead of silently doing nothing.
Signed-off-by: NNikolaus Schulz <mail@microschulz.de>
[guenter.roeck@ericsson.com: Minor formatting cleanup]
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The F75387 supports automatic fan control using either PWM duty cycle or
RPM speed values.  Make the driver detect the latter mode, and expose the
different modes in sysfs as per pwm_enable, so that the user can switch
between them.

The interpretation of the pwm_enable attribute for the F75387 is adjusted
to be a superset of those values used for similar Fintek chips which do
not support automatic duty mode, with 2 mapping to automatic speed mode,
and moving automatic duty mode to the new value 4.

Toggling the duty mode via pwm_enable is currently denied for the F75387,
as the chip then simply reinterprets the fan configuration register values
according to the new mode, switching between RPM and PWM units, which
makes this a dangerous operation.

This patch introduces a new pwm mode into the driver. This is necessary
because the new mode (automatic pwm mode, 4) may already be enabled by the
BIOS, and the driver should not break existing functionality. This was seen
on at least one board.
Signed-off-by: NNikolaus Schulz <mail@microschulz.de>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

Merge branches 'core-urgent-for-linus', 'perf-urgent-for-linus' and 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pulling latest branches from Ingo:

* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  memblock: Fix size aligning of memblock_alloc_base_nid()

* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  perf probe: Ensure offset provided is not greater than function length without DWARF info too
  perf tools: Ensure comm string is properly terminated
  perf probe: Ensure offset provided is not greater than function length
  perf evlist: Return first evsel for non-sample event on old kernel
  perf/hwbp: Fix a possible memory leak

* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  CPU hotplug, cpusets, suspend: Don't touch cpusets during suspend/resume

There is only one error code to return for a bad user-space buffer
pointer passed to a system call in the same address space as the
system call is executed, and that is EFAULT.  Furthermore, the
low-level access routines, which catch most of the faults, return
EFAULT already.
Signed-off-by: NH. Peter Anvin <hpa@zytor.com>
Reviewed-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NRoland McGrath <roland@hack.frob.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>