Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Insert HPET resources after pci probing has been completed in order to
avoid resource conflicts with PCI resource reservation.  With this change
the HPET firmware resources will be identified, but it should also not
cause issues when the HPET address falls on a BAR in a PCI device, and the
PCI enumeration cannot reserve the resources.
Signed-off-by: NAaron Durbin <adurbin@google.com>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When Andi reverted the HPET resource reservation (in commit
0f8dc2f0), he didn't remove the now
unused variables, which just causes gcc to be noisy.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Matthias Lenk reports that the PCI subsystem would move the HPET on
SB400/SB600-based systems, where the HPET is in BAR1 of the SMbus
controller.

The reason? The ACPI layer registered the PCI MMIO range as being busy
too early, before PCI enumeration had happened, causing the PCI layer to
decide that it should relocate the resources somewhere else.

Firmware resources should be marked busy _after_ the PCI enumeration and
probing has happened, not before.

Remove the too-early reservation, we'll fix it up to do it properly
later.  In the meantime, this solves the regression.
Tested-by: NMatthias Lenk <matthias.lenk@amd.com>
Cc: Aaron Durbin <adurbin@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I have a Dell Optiplex GX240 and when I boot Linux, ACPI gets set up by only
acpi=ht.  dmesg shows the following line:

   DELL GX240 detected: force use of acpi=ht

Everything seemed to be fine.  However, I discovered that everything is not
fine.  The USB controller works so slowly that copying a few (uncached) 1
megabyte large photos from a USB-enabled digital camera takes many minutes
instead of a couple of seconds.

I am using Linux 2.6.21.1 on a Debian 4.0 ("Etch") system.

I thought that this might be related to ACPI.  So I tried to boot with _only_
"acpi=force" appended to the kernel command line.  Voila, the USB controller
started to work at full speed and copying photos from my digital camera took
only seconds.

I tested the system with "acpi=force" and could not find anything which did
not work.

I thought that this might be related to interrupts and APIC as well.  (Note
that this is APIC, not ACPI.) I tried booting with _only_ "noapic" and
"nolapic" appended to the command line.  Again, the USB controller started to
work at full speed.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

Default to physical mode on hotplug CPU kernels.  Furher simplify and clean up
the APIC initialization code.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andi Kleen <ak@suse.de>
Cc: "Li, Shaohua" <shaohua.li@intel.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

The root cause of this bug shows that this machine
could not possibly run an ACPI-aware OS without a
model specific workaround.

http://bugzilla.kernel.org/show_bug.cgi?id=5966Signed-off-by: NLen Brown <len.brown@intel.com>

In preparation for supporting generic timekeeping, this patch cleans up
x86-64's use of vxtime.hpet_address, changing it to just hpet_address as is
also used in i386.  This is necessary since the vxtime structure will be going
away.
Signed-off-by: NJohn Stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allow early access to the power management timer by exposing the verified read
function and providing a helper function which checks the pmtmr_ioport
variable and returns either the pm timer readout or 0 in case the pm timer is
not available.

Create a new header file and replace also the ifdef'ed extern definition in
arch/i386/kernel/acpi/boot.c

This is a preperatory patch for the rework of the local apic timer
calibration.

No functional changes.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Returning count for tables that are supposed to be unique
was useless and confusing.
Signed-off-by: NLen Brown <len.brown@intel.com>

Allow ACPI id to be u32 instead of u8.
Requires drop of conversion tables with the acpiid as index.
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NLen Brown <len.brown@intel.com>

Dunno why this pops out in only in the allmodconfig build.
Though the warning is accurate, all the callers of the flagged
non __init function are __init, this is not a functional change.

WARNING: vmlinux - Section mismatch: reference to .init.data:acpi_sci_flags from .text between 'acpi_sci_ioapic_setup' (at offset 0xc010f0a
6) and 'acpi_gsi_to_irq'                                                                                                                   WARNING: vmlinux - Section mismatch: reference to .init.text:mp_override_legacy_irq from .text between 'acpi_sci_ioapic_setup' (at offset 0
xc010f0de) and 'acpi_gsi_to_irq'                                                                                                           WARNING: vmlinux - Section mismatch: reference to .init.data:acpi_sci_override_gsi from .text between 'acpi_sci_ioapic_setup' (at offset 0x
c010f0e4) and 'acpi_gsi_to_irq'
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts commit 281ea49b,
which broke ACPI Interrupt source overrides that move
the SCI from one IRQ in PIC mode to another in IOAPIC mode.

If the SCI shared an interrupt line with another device,
this would result in a "irq 18: nobody cared" type failure.

http://bugzilla.kernel.org/show_bug.cgi?id=7601Signed-off-by: NLen Brown <len.brown@intel.com>

Timer overrides are normally disabled on Nvidia board because
they are commonly wrong, except on new ones with HPET support.
Unfortunately there are quite some Asus boards around that
don't have HPET, but need a timer override.

We don't know yet how to handle this transparently,
but at least add a command line option to force the timer override
and let them boot.

Cc: len.brown@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>

WARNING: vmlinux - Section mismatch: reference to .init.data:acpi_noirq from .text between 'pcibios_penalize_isa_irq' (at offset 0xc026ffa1) and 'pirq_serverworks_get'
Acked-by: N"Brown, Len" <len.brown@intel.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

- Fixes a build problem with CONFIG_M386=y (include file dependencies get
  messy).

- Share the implementation between x86 and x86_64

- These are too big to inline anyway.
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

The Linux group at Stratus Technologies has come across an issue with SCI
routing under ACPI.  We were bitten by this when we made an x86_64 platform
whose BIOS provides an Interrupt Source Override for the SCI itself.
Apparently the override has no effect for the System Control Interrupt, and
this appears to be because of the way the SCI is setup in the ACPI code.
It does not handle the case where busirq != gsi.

The code that sets up the SCI routing assumes that bus irq == global irq.
So there is simply no provision for telling it otherwise.  The attached
patch provides this mechanism.

This patch provided by David Bulkow, was tested on an i386 platform, which
does not use the SCI override, and also on an x86_64 platform which does
use an override.
Signed-off-by: NDavid Bulkow <david.bulkow@stratus.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

After raising the number of irqs the system supports this function is no
longer necessary.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch removes the change in behavior of the irq allocation code when
CONFIG_PCI_MSI is defined.  Removing all instances of the assumption that irq
== vector.

create_irq is rewritten to first allocate a free irq and then to assign that
irq a vector.

assign_irq_vector is made static and the AUTO_ASSIGN case which allocates an
vector not bound to an irq is removed.

The ioapic vector methods are removed, and everything now works with irqs.

The definition of NR_IRQS no longer depends on CONFIG_PCI_MSI

[akpm@osdl.org: cleanup]
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Rajesh Shah <rajesh.shah@intel.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Protasevich, Natalie" <Natalie.Protasevich@UNISYS.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Add HPET(s) into resource map. This will allow for the HPET(s) to be
visibile within /proc/iomem.
Signed-off-by: NAaron Durbin <adurbin@google.com>
Signed-off-by: NAndi Kleen <ak@suse.de>

This patch enables ACPI based physical CPU hotplug support for x86_64.
Implements acpi_map_lsapic() and acpi_unmap_lsapic() to support physical cpu
hotplug.
Signed-off-by: NAshok Raj <ashok.raj@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Cc: Andi Kleen <ak@muc.de>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>

acpi_force can become static.

Cc: len.brown@intel.com
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndi Kleen <ak@suse.de>

And move one into proto.h

Cc: len.brown@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>

Removes code duplication between i386/x86-64.

Not needed anymore in setup.c since early_param cleanup

Cc: len.brown@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>

This patch replaces the open-coded early commandline parsing
throughout the i386 boot code with the generic mechanism (already used
by ppc, powerpc, ia64 and s390).  The code was inconsistent with
whether it deletes the option from the cmdline or not, meaning some of
these will get passed through the environment into init.

This transformation is mainly mechanical, but there are some notable
parts:

1) Grammar: s/linux never set's it up/linux never sets it up/

2) Remove hacked-in earlyprintk= option scanning.  When someone
   actually implements CONFIG_EARLY_PRINTK, then they can use
   early_param().
[AK: actually it is implemented, but I'm adding the early_param it in the next
x86-64 patch]

3) Move declaration of generic_apic_probe() from setup.c into asm/apic.h

4) Various parameters now moved into their appropriate files (thanks Andi).

5) All parse functions which examine arg need to check for NULL,
   except one where it has subtle humor value.

AK: readded acpi_sci handling which was completely dropped
AK: moved some more variables into acpi/boot.c

Cc: len.brown@intel.com
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndi Kleen <ak@suse.de>

ACPI 3.0 appended a variable length UID string to the LAPIC structure
as part of support for > 256 processors.  So the BAD_MADT_ENTRY() sanity
check can no longer compare for equality with a fixed structure length.
Signed-off-by: NAlexey Y Starikovskiy <alexey.y.starikovskiy@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This a bit late (yours patch was posted about a year ago), but
a co-worker of spotted part of the code that looks like a memory
leak. Looking at the code it seems that pci_mmcfg_config should
be free-ed if MMCONFIG is above 4GB.

From: Konrad Rzeszutek <konradr@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Implemented header file support for the following
additional ACPI tables: ASF!, BOOT, CPEP, DBGP, MCFG, SPCR,
SPMI, TCPA, and WDRT. With this support, all current and
known ACPI tables are now defined in the ACPICA headers and
are available for use by device drivers and other software.

Implemented support to allow tables that contain ACPI
names with invalid characters to be loaded. Previously,
this would cause the table load to fail, but since
there are several known cases of such tables on
existing machines, this change was made to enable
ACPI support for them. Also, this matches the
behavior of the Microsoft ACPI implementation.
https://bugzilla.novell.com/show_bug.cgi?id=147621

Fixed a couple regressions introduced during the memory
optimization in the 20060317 release. The namespace
node definition required additional reorganization and
an internal datatype that had been changed to 8-bit was
restored to 32-bit. (Valery Podrezov)

Fixed a problem where a null pointer passed to
acpi_ut_delete_generic_state() could be passed through
to acpi_os_release_object which is unexpected. Such
null pointers are now trapped and ignored, matching
the behavior of the previous implementation before the
deployment of acpi_os_release_object().  (Valery Podrezov,
Fiodor Suietov)

Fixed a memory mapping leak during the deletion of
a SystemMemory operation region where a cached memory
mapping was not deleted. This became a noticeable problem
for operation regions that are defined within frequently
used control methods. (Dana Meyers)

Reorganized the ACPI table header files into two main
files: one for the ACPI tables consumed by the ACPICA core,
and another for the miscellaneous ACPI tables that are
consumed by the drivers and other software. The various
FADT definitions were merged into one common section and
three different tables (ACPI 1.0, 1.0+, and 2.0)
Signed-off-by: NBob Moore <robert.moore@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

This reverts commit 5491d0f3.

As per Andi:

  "After some discussion with people who have the affected system it
   seems best to revert for 2.6.17.  It broke a common BIOS workaround
   and PCI-X still doesn't work.  Alternative is for people to change
   the BIOS which seems to be better right now."
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is needed to see all devices.

The system has multiple PCI segments and we don't handle that properly
yet in PCI and ACPI. Short term before this is fixed blacklist it to
pci=noacpi.

Acked-by: len.brown@intel.com
Cc: gregkh@suse.de
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

We only need to check cpu_has_apic in the IO-APIC/L-APIC parsing, not for
all of ACPI.
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch I submitted earlier to fix disabled LAPIC handling in ACPI was
mismerged for some reason I still don't quite understand.  Parts of it was
applied to the wrong function.

This patch fixes it up.

Cc: <len.brown@intel.com>
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The patch I submitted earlier to fix disabled LAPIC handling in ACPI
was mismerged for some reason I still don't quite understand. Parts
of it was applied to the wrong function.

This patch fixes it up.

Cc: len.brown@intel.com
Signed-off-by: NAndi Kleen <ak@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>