When using the MAPv4 packet format in conjunction with MAP commands,
a dummy DL checksum trailer will be appended to the packet. Before
this packet is sent out as an ACK, the DL checksum trailer needs to be
removed.
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using the MAPv4 packet format, receive checksum offload can be
enabled in hardware. The checksum computation over pseudo header is
not offloaded but the rest of the checksum computation over
the payload is offloaded. This applies only for TCP / UDP packets
which are not fragmented.

rmnet validates the TCP/UDP checksum for the packet using the checksum
from the checksum trailer added to the packet by hardware. The
validation performed is as following -

1. Perform 1's complement over the checksum value from the trailer
2. Compute 1's complement checksum over IPv4 / IPv6 header and
   subtracts it from the value from step 1
3. Computes 1's complement checksum over IPv4 / IPv6 pseudo header and
   adds it to the value from step 2
4. Subtracts the checksum value from the TCP / UDP header from the
   value from step 3.
5. Compares the value from step 4 to the checksum value from the
   TCP / UDP header.
6. If the comparison in step 5 succeeds, CHECKSUM_UNNECESSARY is set
   and the packet is passed on to network stack. If there is a
   failure, then the packet is passed on as such without modifying
   the ip_summed field.

The checksum field is also checked for UDP checksum 0 as per RFC 768
and for unexpected TCP checksum of 0.

If checksum offload is disabled when using MAPv4 packet format in
receive path, the packet is queued as is to network stack without
the validations above.
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MAPv4 packet format adds support for RX / TX checksum offload.
For a bi-directional UDP stream at a rate of 570 / 146 Mbps, roughly
10% CPU cycles are saved.

For receive path, there is a checksum trailer appended to the end of
the MAP packet. The valid field indicates if hardware has computed
the checksum. csum_start_offset indicates the offset from the start
of the IP header from which hardware has computed checksum.
csum_length is the number of bytes over which the checksum was
computed and the resulting value is csum_value.

In the transmit path, a header is appended between the end of the MAP
header and the start of the IP packet. csum_start_offset is the offset
in bytes from which hardware will compute the checksum if the
csum_enabled bit is set. udp_ip4_ind indicates if the checksum
value of 0 is valid or not. csum_insert_offset is the offset from the
csum_start_offset where hardware will insert the computed checksum.

The use of this additional packet format for checksum offload is
explained in subsequent patches.
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The real device over which the rmnet devices are installed also
aggregate multiple IP packets and sends them as a single large
aggregate frame to the hardware. This causes degraded throughput
for TCP TX due to bufferbloat.

To overcome this problem, pacing shift value of 8 is set using the
sk_pacing_shift_update() helper. This value was determined based
on experiments with a single stream TCP TX using iperf for a
duration of 30s.

Pacing shift | Observed data rate (Mbps)
          10 | 9
           9 | 140
           8 | 146 (Max link rate)
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is done so that we can use this field for both ingress and
egress flags.
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rmnet_map_demultiplex() is only declared but not defined anywhere,
so remove it.
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rmnet devices cannot have a mux id of 255. This is validated when
assigning the mux id to the rmnet devices. As a result, checking for
mux id 255 does not apply in egress path.
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We already check the headroom once in rmnet_map_egress_handler(),
so this is not needed.
Signed-off-by: NSubash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
ipv6: Align nexthop behaviour with IPv4

This set tries to eliminate some differences between IPv4's and IPv6's
treatment of nexthops. These differences are most likely a side effect
of IPv6's data structures (specifically 'rt6_info') that incorporate
both the route and the nexthop and the late addition of ECMP support in
commit 51ebd318 ("ipv6: add support of equal cost multipath
(ECMP)").

IPv4 and IPv6 do not react the same to certain netdev events. For
example, upon carrier change affected IPv4 nexthops are marked using the
RTNH_F_LINKDOWN flag and the nexthop group is rebalanced accordingly.
IPv6 on the other hand, does nothing which forces us to perform a
carrier check during route lookup and dump. This makes it difficult to
introduce features such as non-equal-cost multipath that are built on
top of this set [1].

In addition, when a netdev is put administratively down IPv4 nexthops
are marked using the RTNH_F_DEAD flag, whereas IPv6 simply flushes all
the routes using these nexthops. To be consistent with IPv4, multipath
routes should only be flushed when all nexthops in the group are
considered dead.

The first 12 patches introduce non-functional changes that store the
RTNH_F_DEAD and RTNH_F_LINKDOWN flags in IPv6 routes based on netdev
events, in a similar fashion to IPv4. This allows us to remove the
carrier check performed during route lookup and dump.

The next three patches make sure we only flush a multipath route when
all of its nexthops are dead.

Last three patches add test cases for IPv4/IPv6 FIB. These verify that
both address families react similarly to netdev events.

Finally, this series also serves as a good first step towards David
Ahern's goal of treating nexthops as standalone objects [2], as it makes
the code more in line with IPv4 where the nexthop and the nexthop group
are separate objects from the route itself.

1. https://github.com/idosch/linux/tree/ipv6-nexthops
2. http://vger.kernel.org/netconf2017_files/nexthop-objects.pdf

Changes since RFC (feedback from David Ahern):
* Remove redundant declaration of rt6_ifdown() in patch 4 and adjust
comment referencing it accordingly
* Drop patch to flush multipath routes upon NETDEV_UNREGISTER. Reword
cover letter accordingly
* Use a temporary variable to make code more readable in patch 15
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check that IPv4 and IPv6 react the same when the carrier of a netdev is
toggled. Local routes should not be affected by this, whereas unicast
routes should.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check that IPv4 and IPv6 react the same when a netdev is being put
administratively down.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test cases to check that IPv4 and IPv6 react to a netdev being
unregistered as expected.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, IPv6 deletes nexthops from a multipath route when the
nexthop device is put administratively down. This differs from IPv4
where the nexthops are kept, but marked with the RTNH_F_DEAD flag. A
multipath route is flushed when all of its nexthops become dead.

Align IPv6 with IPv4 and have it conform to the same guidelines.

In case the multipath route needs to be flushed, its siblings are
flushed one by one. Otherwise, the nexthops are marked with the
appropriate flags and the tree walker is instructed to skip all the
siblings.

As explained in previous patches, care is taken to update the sernum of
the affected tree nodes, so as to prevent the use of wrong dst entries.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The next patch is going to allow dead routes to remain in the FIB tree
in certain situations.

When this happens we need to be sure to bump the sernum of the nodes
where these are stored so that potential copies cached in sockets are
invalidated.

The function that performs this update assumes the table lock is not
taken when it is invoked, but that will not be the case when it is
invoked by the tree walker.

Have the function assume the lock is taken and make the single caller
take the lock itself.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are going to allow dead routes to stay in the FIB tree (e.g., when
they are part of a multipath route, directly connected route with no
carrier) and revive them when their nexthop device gains carrier or when
it is put administratively up.

This is equivalent to the addition of the route to the FIB tree and we
should therefore take care of updating the sernum of all the parent
nodes of the node where the route is stored. Otherwise, we risk sockets
caching and using sub-optimal dst entries.

Export the function that performs the above, so that it could be invoked
from fib6_ifup() later on.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As explained in previous patch, fib6_ifdown() needs to consider the
state of all the sibling routes when a multipath route is traversed.

This is done by evaluating all the siblings when the first sibling in a
multipath route is traversed. If the multipath route does not need to be
flushed (e.g., not all siblings are dead), then we should just skip the
multipath route as our work is done.

Have the tree walker jump to the last sibling when it is determined that
the multipath route needs to be skipped.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When routes that are a part of a multipath route are evaluated by
fib6_ifdown() in response to NETDEV_DOWN and NETDEV_UNREGISTER events
the state of their sibling routes is not considered.

This will change in subsequent patches in order to align IPv6 with
IPv4's behavior. For example, when the last sibling in a multipath route
becomes dead, the entire multipath route needs to be removed.

To prevent the tree walker from re-evaluating all the sibling routes
each time, we can simply evaluate them once - when the first sibling is
traversed.

If we determine the entire multipath route needs to be removed, then the
'should_flush' bit is set in all the siblings, which will cause the
walker to flush them when it traverses them.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now the RTNH_F_DEAD flag was only reported in route dump when
the 'ignore_routes_with_linkdown' sysctl was set. This is expected as
dead routes were flushed otherwise.

The reliance on this sysctl is going to be removed, so we need to report
the flag regardless of the sysctl's value.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, dead routes are only present in the routing tables in case
the 'ignore_routes_with_linkdown' sysctl is set. Otherwise, they are
flushed.

Subsequent patches are going to remove the reliance on this sysctl and
make IPv6 more consistent with IPv4.

Before this is done, we need to make sure dead routes are skipped during
route lookup, so as to not cause packet loss.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to previous patch, there is no need to check for the carrier of
the nexthop device when dumping the route and we can instead check for
the presence of the RTNH_F_LINKDOWN flag.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the RTNH_F_LINKDOWN flag is set in nexthops, we can avoid the
need to dereference the nexthop device and check its carrier and instead
check for the presence of the flag.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is valid to install routes with a nexthop device that does not have a
carrier, so we need to make sure they're marked accordingly.

As explained in the previous patch, host and anycast routes are never
marked with the 'linkdown' flag.

Note that reject routes are unaffected, as these use the loopback device
which always has a carrier.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to IPv4, when the carrier of a netdev changes we should toggle
the 'linkdown' flag on all the nexthops using it as their nexthop
device.

This will later allow us to test for the presence of this flag during
route lookup and dump.

Up until commit 4832c30d ("net: ipv6: put host and anycast routes on
device with address") host and anycast routes used the loopback netdev
as their nexthop device and thus were not marked with the 'linkdown'
flag. The patch preserves this behavior and allows one to ping the local
address even when the nexthop device does not have a carrier and the
'ignore_routes_with_linkdown' sysctl is set.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To make IPv6 more in line with IPv4 we need to be able to respond
differently to different netdev events. For example, when a netdev is
unregistered all the routes using it as their nexthop device should be
flushed, whereas when the netdev's carrier changes only the 'linkdown'
flag should be toggled.

Currently, this is not possible, as the function that traverses the
routing tables is not aware of the triggering event.

Propagate the triggering event down, so that it could be used in later
patches.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous patch marked nexthops with the 'dead' and 'linkdown' flags.
Clear these flags when the netdev comes back up.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a netdev is put administratively down or unregistered all the
nexthops using it as their nexthop device should be marked with the
'dead' and 'linkdown' flags.

Currently, when a route is dumped its nexthop device is tested and the
flags are set accordingly. A similar check is performed during route
lookup.

Instead, we can simply mark the nexthops based on netdev events and
avoid checking the netdev's state during route dump and lookup.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By the time fib6_net_exit() is executed all the netdevs in the namespace
have been either unregistered or pushed back to the default namespace.
That is because pernet subsys operations are always ordered before
pernet device operations and therefore invoked after them during
namespace dismantle.

Thus, all the routing tables in the namespace are empty by the time
fib6_net_exit() is invoked and the call to rt6_ifdown() can be removed.

This allows us to simplify the condition in fib6_ifdown() as it's only
ever called with an actual netdev.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf-next 2018-01-07

The following pull-request contains BPF updates for your *net-next* tree.

The main changes are:

1) Add a start of a framework for extending struct xdp_buff without
   having the overhead of populating every data at runtime. Idea
   is to have a new per-queue struct xdp_rxq_info that holds read
   mostly data (currently that is, queue number and a pointer to
   the corresponding netdev) which is set up during rxqueue config
   time. When a XDP program is invoked, struct xdp_buff holds a
   pointer to struct xdp_rxq_info that the BPF program can then
   walk. The user facing BPF program that uses struct xdp_md for
   context can use these members directly, and the verifier rewrites
   context access transparently by walking the xdp_rxq_info and
   net_device pointers to load the data, from Jesper.

2) Redo the reporting of offload device information to user space
   such that it works in combination with network namespaces. The
   latter is reported through a device/inode tuple as similarly
   done in other subsystems as well (e.g. perf) in order to identify
   the namespace. For this to work, ns_get_path() has been generalized
   such that the namespace can be retrieved not only from a specific
   task (perf case), but also from a callback where we deduce the
   netns (ns_common) from a netdevice. bpftool support using the new
   uapi info and extensive test cases for test_offload.py in BPF
   selftests have been added as well, from Jakub.

3) Add two bpftool improvements: i) properly report the bpftool
   version such that it corresponds to the version from the kernel
   source tree. So pick the right linux/version.h from the source
   tree instead of the installed one. ii) fix bpftool and also
   bpf_jit_disasm build with bintutils >= 2.9. The reason for the
   build breakage is that binutils library changed the function
   signature to select the disassembler. Given this is needed in
   multiple tools, add a proper feature detection to the
   tools/build/features infrastructure, from Roman.

4) Implement the BPF syscall command BPF_MAP_GET_NEXT_KEY for the
   stacktrace map. It is currently unimplemented, but there are
   use cases where user space needs to walk all stacktrace map
   entries e.g. for dumping or deleting map entries w/o having to
   close and recreate the map. Add BPF selftests along with it,
   from Yonghong.

5) Few follow-up cleanups for the bpftool cgroup code: i) rename
   the cgroup 'list' command into 'show' as we have it for other
   subcommands as well, ii) then alias the 'show' command such that
   'list' is accepted which is also common practice in iproute2,
   and iii) remove couple of newlines from error messages using
   p_err(), from Jakub.

6) Two follow-up cleanups to sockmap code: i) remove the unused
   bpf_compute_data_end_sk_skb() function and ii) only build the
   sockmap infrastructure when CONFIG_INET is enabled since it's
   only aware of TCP sockets at this time, from John.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Yonghong Song says:

====================
The patch set implements bpf syscall command BPF_MAP_GET_NEXT_KEY
for stacktrace map. Patch #1 is the core implementation
and Patch #2 implements a bpf test at tools/testing/selftests/bpf
directory. Please see individual patch comments for details.

Changelog:
  v1 -> v2:
   - For invalid key (key pointer is non-NULL), sets next_key to be the first valid key.
====================
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Added a bpf selftest in test_progs at tools directory for stacktrace.
The test will populate a hashtable map and a stacktrace map
at the same time with the same key, stackid.
The user space will compare both maps, using BPF_MAP_LOOKUP_ELEM
command and BPF_MAP_GET_NEXT_KEY command, to ensure that both have
the same set of keys.
Signed-off-by: NYonghong Song <yhs@fb.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Currently, bpf syscall command BPF_MAP_GET_NEXT_KEY is not
supported for stacktrace map. However, there are use cases where
user space wants to enumerate all stacktrace map entries where
BPF_MAP_GET_NEXT_KEY command will be really helpful.
In addition, if user space wants to delete all map entries
in order to save memory and does not want to close the
map file descriptor, BPF_MAP_GET_NEXT_KEY may help improve
performance if map entries are sparsely populated.

The implementation has similar behavior for
BPF_MAP_GET_NEXT_KEY implementation in hashtab. If user provides
a NULL key pointer or an invalid key, the first key is returned.
Otherwise, the first valid key after the input parameter "key"
is returned, or -ENOENT if no valid key can be found.
Signed-off-by: NYonghong Song <yhs@fb.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>

Jesper Dangaard Brouer says:

====================
V4:
* Added reviewers/acks to patches
* Fix patch desc in i40e that got out-of-sync with code
* Add SPDX license headers for the two new files added in patch 14

V3:
* Fixed bug in virtio_net driver
* Removed export of xdp_rxq_info_init()

V2:
* Changed API exposed to drivers
  - Removed invocation of "init" in drivers, and only call "reg"
    (Suggested by Saeed)
  - Allow "reg" to fail and handle this in drivers
    (Suggested by David Ahern)
* Removed the SINKQ qtype, instead allow to register as "unused"
* Also fixed some drivers during testing on actual HW (noted in patches)

There is a need for XDP to know more about the RX-queue a given XDP
frames have arrived on.  For both the XDP bpf-prog and kernel side.

Instead of extending struct xdp_buff each time new info is needed,
this patchset takes a different approach.  Struct xdp_buff is only
extended with a pointer to a struct xdp_rxq_info (allowing for easier
extending this later).  This xdp_rxq_info contains information related
to how the driver have setup the individual RX-queue's.  This is
read-mostly information, and all xdp_buff frames (in drivers
napi_poll) point to the same xdp_rxq_info (per RX-queue).

We stress this data/cache-line is for read-mostly info.  This is NOT
for dynamic per packet info, use the data_meta for such use-cases.

This patchset start out small, and only expose ingress_ifindex and the
RX-queue index to the XDP/BPF program. Access to tangible info like
the ingress ifindex and RX queue index, is fairly easy to comprehent.
The other future use-cases could allow XDP frames to be recycled back
to the originating device driver, by providing info on RX device and
queue number.

As XDP doesn't have driver feature flags, and eBPF code due to
bpf-tail-calls cannot determine that XDP driver invoke it, this
patchset have to update every driver that support XDP.

For driver developers (review individual driver patches!):

The xdp_rxq_info is tied to the drivers RX-ring(s). Whenever a RX-ring
modification require (temporary) stopping RX frames, then the
xdp_rxq_info should (likely) also be unregistred and re-registered,
especially if reallocating the pages in the ring. Make sure ethtool
set_channels does the right thing. When replacing XDP prog, if and
only if RX-ring need to be changed, then also re-register the
xdp_rxq_info.

I'm Cc'ing the individual driver patches to the registered maintainers.

Testing:

I've only tested the NIC drivers I have hardware for.  The general
test procedure is to (DUT = Device Under Test):
 (1) run pktgen script pktgen_sample04_many_flows.sh       (against DUT)
 (2) run samples/bpf program xdp_rxq_info --dev $DEV       (on DUT)
 (3) runtime modify number of NIC queues via ethtool -L    (on DUT)
 (4) runtime modify number of NIC ring-size via ethtool -G (on DUT)

Patch based on git tree bpf-next (at commit fb982666):
 https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next.git/
====================
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

This sample program can be used for monitoring and reporting how many
packets per sec (pps) are received per NIC RX queue index and which
CPU processed the packet. In itself it is a useful tool for quickly
identifying RSS imbalance issues, see below.

The default XDP action is XDP_PASS in-order to provide a monitor
mode. For benchmarking purposes it is possible to specify other XDP
actions on the cmdline --action.

Output below shows an imbalance RSS case where most RXQ's deliver to
CPU-0 while CPU-2 only get packets from a single RXQ.  Looking at
things from a CPU level the two CPUs are processing approx the same
amount, BUT looking at the rx_queue_index levels it is clear that
RXQ-2 receive much better service, than other RXQs which all share CPU-0.

Running XDP on dev:i40e1 (ifindex:3) action:XDP_PASS
XDP stats       CPU     pps         issue-pps
XDP-RX CPU      0       900,473     0
XDP-RX CPU      2       906,921     0
XDP-RX CPU      total   1,807,395

RXQ stats       RXQ:CPU pps         issue-pps
rx_queue_index    0:0   180,098     0
rx_queue_index    0:sum 180,098
rx_queue_index    1:0   180,098     0
rx_queue_index    1:sum 180,098
rx_queue_index    2:2   906,921     0
rx_queue_index    2:sum 906,921
rx_queue_index    3:0   180,098     0
rx_queue_index    3:sum 180,098
rx_queue_index    4:0   180,082     0
rx_queue_index    4:sum 180,082
rx_queue_index    5:0   180,093     0
rx_queue_index    5:sum 180,093
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Now all XDP driver have been updated to setup xdp_rxq_info and assign
this to xdp_buff->rxq.  Thus, it is now safe to enable access to some
of the xdp_rxq_info struct members.

This patch extend xdp_md and expose UAPI to userspace for
ingress_ifindex and rx_queue_index.  Access happens via bpf
instruction rewrite, that load data directly from struct xdp_rxq_info.

* ingress_ifindex map to xdp_rxq_info->dev->ifindex
* rx_queue_index  map to xdp_rxq_info->queue_index
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Hook points for xdp_rxq_info:
 * reg  : netif_alloc_rx_queues
 * unreg: netif_free_rx_queues

The net_device have some members (num_rx_queues + real_num_rx_queues)
and data-area (dev->_rx with struct netdev_rx_queue's) that were
primarily used for exporting information about RPS (CONFIG_RPS) queues
to sysfs (CONFIG_SYSFS).

For generic XDP extend struct netdev_rx_queue with the xdp_rxq_info,
and remove some of the CONFIG_SYSFS ifdefs.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

The virtio_net driver doesn't dynamically change the RX-ring queue
layout and backing pages, but instead reject XDP setup if all the
conditions for XDP is not meet.  Thus, the xdp_rxq_info also remains
fairly static.  This allow us to simply add the reg/unreg to
net_device open/close functions.

Driver hook points for xdp_rxq_info:
 * reg  : virtnet_open
 * unreg: virtnet_close

V3:
 - bugfix, also setup xdp.rxq in receive_mergeable()
 - Tested bpf-sample prog inside guest on a virtio_net device

Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Driver hook points for xdp_rxq_info:
 * reg  : tun_attach
 * unreg: __tun_detach

I've done some manual testing of this tun driver, but I would
appriciate good review and someone else running their use-case tests,
as I'm not 100% sure I understand the tfile->detached semantics.

V2: Removed the skb_array_cleanup() call from V1 by request from Jason Wang.

Cc: Jason Wang <jasowang@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Reviewed-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

This driver uses a bool scheme for "enable"/"disable" when setting up
different resources.  Thus, the hook points for xdp_rxq_info is done
in the same function call nicvf_rcv_queue_config().  This is activated
through enable/disable via nicvf_config_data_transfer(), which is tied
into nicvf_stop()/nicvf_open().

Extending driver packet handler call-path nicvf_rcv_pkt_handler() with
a pointer to the given struct rcv_queue, in-order to access the
xdp_rxq_info data area (in nicvf_xdp_rx()).

V2: Driver have no proper error path for failed XDP RX-queue info reg,
as nicvf_rcv_queue_config is a void function.

Cc: linux-arm-kernel@lists.infradead.org
Cc: Sunil Goutham <sgoutham@cavium.com>
Cc: Robert Richter <rric@kernel.org>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Driver hook points for xdp_rxq_info:
 * reg  : nfp_net_rx_ring_alloc
 * unreg: nfp_net_rx_ring_free

In struct nfp_net_rx_ring moved member @size into a hole on 64-bit.
Thus, the size remaines the same after adding member @xdp_rxq.

Cc: oss-drivers@netronome.com
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Simon Horman <simon.horman@netronome.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>

Driver hook points for xdp_rxq_info:
 * reg  : bnxt_alloc_rx_rings
 * unreg: bnxt_free_rx_rings

This driver should be updated to re-register when changing
allocation mode of RX rings.

Tested on actual hardware.

Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>