There are 2 different things:
- sub-menu for "Atheros Wireless cards" family
- module ath.ko with common Atheros code

Until now, they both used to depend on the same Kconfig variable ATH_COMMON.
Thus, being "Atheros card" and "depending on ath.ko" was the same.

To allow module to belong to the
"Atheros Wireless cards" family but not use ath.ko,
2 conditions above need to be separated.

So, this patch introduce new Kconfig variable ATH_CARDS for belonging
to the "Atheros Wireless Cards" family; while ATH_COMMON becomes hidden
variable to express dependency on common Atheros code in ath.ko. Modules
that depend on this common code now express it by setting ATH_COMMON.

Right now, ath6kl do not depend on common code and thus do not set ATH_COMMON.
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

'bf_next' is cleared using ATH_TXBUF_RESET() in both the
callsites of ath_tx_get_buffer().
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The ethtool statistics are available only when
CONFIG_ATH9K_DEBUGFS is enabled, move these functions
to debug.c
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NPetr Stetiar <ynezz@true.cz>
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for advertising GreenField, 40MHz intolerance
or LDPC coding support to cfg80211.
Signed-off-by: NAvinash Patil <patila@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit "ath9k: stomp audio profiles on weak signal
strength" failed to take care of new stomp type while
programming concurrent tx priority. That leads to array
index out of bounds access.

drivers/net/wireless/ath/ath9k/btcoex.c:414
        ath9k_hw_btcoex_set_concur_txprio()
               error: buffer overflow 'stomp_txprio' 4 <= 4
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If CONFIG_SSB_EMBEDDED or CONFIG_SSB_DRIVER_MIPS is set and
CONFIG_SSB_DRIVER_EXTIF is not set, it will cause compile problems
because of missing functions. This patch fixes these problems.

The mips driver now also uses ssb_chipco_available() instead of
checking bus->chipco.dev manually.
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes the following warning:

  CC      drivers/bcma/driver_pci_host.o
drivers/bcma/driver_pci_host.c: In function 'bcma_core_pci_fixup_addresses':
drivers/bcma/driver_pci_host.c:555:23: error: ignoring return value of
'pci_assign_resource', declared with attribute warn_unused_result
[-Werror=unused-result]
Reported-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The LMAC API states that the TSF clock value of
every rx'ed frame is a "usec accurate timestamp
of the hardware clock at the end of frame
(before OFDM SIFS EOF padding)".
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Tested-by: NKalle Valo <kvalo@adurom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The vendor radiotap patch added a few fields to
struct ieee80211_rx_status that need to be zero,
initialize the struct instead of using whatever
was left on the stack.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Adding __printf helps spot format and argument mismatches.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The frequencies will be printed when actually
doing the scan, and the IEs can be captured
on the hwsim0 monitor.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the number of channels is > 1, which means that
hwsim will use mac80211 channel contexts, it can
also advertise VHT support.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Convert mac80211 (and where necessary, some drivers a
little bit) to the new channel definition struct.

This will allow extending mac80211 for VHT, which is
currently restricted to channel contexts since there
are no drivers using that which makes it easier. As
I also don't care about VHT for drivers not using the
channel context API, I won't convert the previous API
to VHT support.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Change nl80211 to support specifying a VHT (or HT)
using the control channel frequency (as before) and
new attributes for the channel width and first and
second center frequency. The old channel type is of
course still supported for HT.

Also change the cfg80211 channel definition struct
to support these by adding the relevant fields to
it (and removing the _type field.)

This also adds new helper functions:
 - cfg80211_chandef_create to create a channel def
   struct given the control channel and channel type,
 - cfg80211_chandef_identical to check if two channel
   definitions are identical
 - cfg80211_chandef_compatible to check if the given
   channel definitions are compatible, and return the
   wider of the two

This isn't entirely complete, but that doesn't matter
until we have a driver using it. In particular, it's
missing
 - regulatory checks on the usable bandwidth (if that
   even makes sense)
 - regulatory TX power (database can't deal with it)
 - a proper channel compatibility calculation for the
   new channel types
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of passing a channel pointer and channel type
to all functions and driver methods, pass a new channel
definition struct. Right now, this struct contains just
the control channel and channel type, but for VHT this
will change.

Also, add a small inline cfg80211_get_chandef_type() so
that drivers don't need to use the _type field of the
new structure all the time, which will change.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As mwifiex (and mac80211 in the software case) are the
only drivers actually implementing remain-on-channel
with channel type, userspace can't be relying on it.
This is the case, as it's used only for P2P operations
right now.

Rather than adding a flag to tell userspace whether or
not it can actually rely on it, simplify all the code
by removing the ability to use different channel types.
Leave only the validation of the attribute, so that if
we extend it again later (with the needed capability
flag), it can't break userspace sending invalid data.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

  CC      drivers/net/wireless/rtlwifi/rtl8723ae/trx.o
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c: In function ‘rtl8723ae_rx_query_desc’:
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:324:21: error: ‘RX_FLAG_MACTIME_MPDU’ undeclared (first use in this function)
drivers/net/wireless/rtlwifi/rtl8723ae/trx.c:324:21: note: each undeclared identifier is reported only once for each function it appears in
make[3]: *** [drivers/net/wireless/rtlwifi/rtl8723ae/trx.o] Error 1
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

One of the debug macro invocations ended up with a stray 0 argument
where the format string should be. Remove it.
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fixes sparse warning:
drivers/net/wireless/brcm80211/brcmsmac/main.c:308:10: sparse: symbol 'wlc_prio2prec_map' was not declared. Should it be static?
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'stations' debugfs file has multiple issues. It doesn't scale
to an arbitrary number of associated stations and allocating
64K is not elegant either. Now that changes have been made in
mac80211 to support dynamic creation/deletion of driver-specific
debugfs files on station addition/removal, remove this file and
make use of the mac80211 hooks (which will be done in a sebsequent
patch).
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the rate statistics only when debugfs has been enabled
in ath9k and mac80211 and move the stat() functions under proper
conditionals.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the rate control statistics debugfs file properly
via remove_sta_debugfs(). Also, check for both MAC80211_DEBUGFS
and ATH9K_DEBUGFS config options.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 'xmit' debugfs file has become big and unwieldy, fix
multiple issues with its usage:

* Store TX counters/statistics only for the 4 Access Categories.
  Use IEEE80211_NUM_ACS instead of ATH9K_NUM_TX_QUEUES.

* Move various utility macros to debug.h, they can be reused
  elsewhere.

* Remove tx_complete_poll_work_seen.

* Remove code that accesses various internal queue-specific
  variables without any locking whatsoever. HW/SW queue details
  will be handled in a subsequent patch.

* Do not print internal values like txq_headidx and txq_headidx.
  They were mostly unused anyway, considering code like:
  PRX("txq_tailidx:     ", txq_headidx);

* Handle 'txprocdesc' for EDMA too.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the macros provided by mac80211 and remove redundant
declarations inside the drivers.
Signed-off-by: NSujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move regulatory domain initialization code to a separate function.
Signed-off-by: NStanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On lower WLAN signal strength, WLAN downlink traffic might suffer
from retransmissions. At the mean time, playing SCO/A2DP profiles
is affecting WLAN stability. In such scenario, by stomping SCO/A2DP
BT traffic completely for a BTCOEX period, gives WLAN traffic an
oppertunity to recover PHY rate. It also improves WLAN stability at
lower RSSI without sacificing BT traffic.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch reverts the commit "ath9k_hw: Wait BT calibration to complete"
and bail out from MCI interrupt routine for chip reset. The above commit
stalls the WLAN TCP traffic while bringing up and down the BT interface
iteratively. Fixing this properly by queueing up chip reset and bailing
out properly from tasklet routine.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

FATAL and WATCHDOG interrupts should be processed first followed
by others.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This avoids build failures on some architectures...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NArend van Spriel <arend@broadcom.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NArend van Spriel <arend@broadcom.com>

These messages clutter up the trace buffer without adding any useful
information.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Tested-by: NDaniel Wagner <wagi@monom.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Tested-by: NDaniel Wagner <wagi@monom.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Tested-by: NDaniel Wagner <wagi@monom.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the brcmsmac_tx trace system for tx debugging. Existing code to dump
tx status and descriptors are converted to using tracepoints, allowing
for more efficient collection and post-processing of this data. These
tracepoints are placed to collect data for all tx frames instead of only
on errors. Logging of tx errors is also improved.
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Tested-by: NDaniel Wagner <wagi@monom.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>