The wrong bit was masked when acking langwell gpio interrupts.

Reason for maskig the wrong bit was probably because__ffs() and ffs() functions
return bit indexes differently (0..31 vs 1..32)

This fixes langwell based devices from hanging when a gpio interrupt is
triggered and undoes the breakage which occurred in change set
732063b9Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (277 commits)
  [SCSI] isci: fix checkpatch errors
  isci: Device reset should request sas_phy_reset(phy, true)
  isci: pare back error messsages
  isci: cleanup silicon revision detection
  isci: merge scu_unsolicited_frame.h into unsolicited_frame_control.h
  isci: merge sata.[ch] into request.c
  isci: kill 'get/set' macros
  isci: retire scic_sds_ and scic_ prefixes
  isci: unify isci_host and scic_sds_controller
  isci: unify isci_remote_device and scic_sds_remote_device
  isci: unify isci_port and scic_sds_port
  isci: fix scic_sds_remote_device_terminate_requests
  isci: unify isci_phy and scic_sds_phy
  isci: unify isci_request and scic_sds_request
  isci: rename / clean up scic_sds_stp_request
  isci: preallocate requests
  isci: combine request flags
  isci: unify can_queue tracking on the tci_pool, uplevel tag assignment
  isci: Terminate dev requests on FIS err bit rx in NCQ
  isci: fix frame received locking
  ...

* 'at91/fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-2.6-arm-soc:
  AT91: Change nand buswidth logic to match hardware default configuration
  at91: Use "pclk" as con_id on at91cap9 and at91rm9200
  at91: fix udc, ehci and mmc clock device name for cap9/9g45/9rl
  atmel_serial: fix internal port num
  at91: fix at91_set_serial_console: use platform device id

Merge branch 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x

* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-3.x:
  vesafb: fix memory leak
  fbdev: amba: Link fb device to its parent
  fsl-diu-fb: remove check for pixel clock ranges
  udlfb: Correct sub-optimal resolution selection.
  hecubafb: add module_put on error path in hecubafb_probe()
  sm501fb: fix section mismatch warning
  gx1fb: Fix section mismatch warnings
  fbdev: sh_mobile_meram: Correct pointer check for YCbCr chroma plane

Commits 71c29bd5 ("IB/uverbs: Add devnode method to set path/mode")
and c3af0980 ("IB: Add devnode methods to cm_class and umad_class")
added devnode methods that set the mode.

However, these methods don't check for a NULL mode, and so we get a
crash when unloading modules because devtmpfs_delete_node() calls
device_get_devnode() with mode == NULL.

Add the missing checks.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.de>
[ Also fix cm.c.  - Roland ]
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The recently modified nand buswitth configuration is not aligned with
board reality: the double footprint on boards is always populated with 8bits
buswidth nand flashes.
So we have to consider that without particular configuration the 8bits
buswidth is selected by default.
Moreover, the previous logic was always using !board_have_nand_8bit(), we
change it to a simpler: board_have_nand_16bit().
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

When releasing framebuffer, free colourmap allocations.
Signed-off-by: NDaniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

* 'pm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
  PM / Runtime: Update documentation regarding driver removal
  PM: Documentation: fix typo: pm_runtime_idle_sync() doesn't exist.

Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: set socket send and receive timeouts before attempting connect

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (k10temp) Update documentation for Fam12h
  hwmon-vid: Fix typo in VIA CPU name
  hwmon: (f71882fg) Add support for the F71869A
  hwmon: Use <> rather than () around my e-mail address
  hwmon: (emc6w201) Properly handle all errors

Add some CPU series IDs and links to the Fam12h datasheets.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

It's Nehemiah, not Nemiah.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The F71869A is almost the same as the F71869F/E, except that it has
the normal number of temp and pwm zones for a F71882FG derived chip,
rather then the limited number of the F71869F/E.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Tested-by: NMax Baldwin <archerseven@gmail.com>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Handle errors on 8-bit register reads and writes too. Also use likely
and unlikely to make the functions faster on success.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Acked-by: NGuenter Roeck <guenter.roeck@ericsson.com>

The hard_reset parameter passed to the LLDD in the direct-attached
phy control case allows the LLDD to filter link failure events
while the direct-attached device reset is executing.
Signed-off-by: NJeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The messages emitted from task.c and some from request.c likely
duplicate (in a less undertandable way) what is reported by the
midlayer.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Perform checking per-pci device (even though all systems will only have
1 pci device in this generation), and delete support for silicon that
does not report a proper revision (i.e. A0).
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Does not need its own file.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Undo some needless separation.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Most of these simple dereference macros are longer than their open coded
equivalent.  Deleting enum sci_controller_mode is thrown in for good
measure.
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The distinction between scic_sds_ scic_ and sci_ are no longer relevant
so just unify the prefixes on sci_.  The distinction between isci_ and
sci_ is historically significant, and useful for comparing the old
'core' to the current Linux driver. 'sci_' represents the former core as
well as the routines that are closer to the hardware and protocol than
their 'isci_' brethren. sci == sas controller interface.

Also unwind the 'sds1' out of the parameter structs.
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Remove the distinction between these two implementations and unify on
isci_host (local instances named ihost).  Hmmm, we had two
'oem_parameters' instances, one was unused... nice.
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Remove the distinction between these two implementations and unify on
isci_remote_device (local instances named idev).
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Remove the distinction between these two implementations and unify on
isci_port (local instances named iport).  The duplicate '->owning_port' and
'->isci_port' in both isci_phy and isci_remote_device will be fixed in a later
patch... this is just the straightforward rename/unification.
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Commit 0815632 "isci: unify remote_device stop_handlers" introduced the
possibility that not all requests get terminated if we reach the
request_count.  Now that we properly reference count devices we don't
need this self-defense and can do the straightforward scan of all active
requests.
Reported-by: NJeff Skirvin <jeffrey.d.skirvin@intel.com>
Acked-by: NJeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

They are one in the same object so remove the distinction.  The near
duplicate fields (owning_port, and isci_port) will be cleaned up
after the scic_sds_port isci_port unification.
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

They are one in the same object so remove the distinction.  The near
duplicate fields (owning_controller, and isci_host) will be cleaned up
after the scic_sds_contoller isci_host unification.
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

* Rename scic_sds_stp_request to isci_stp_request
* Remove the unused fields and union indirection
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

the dma_pool interface is optimized for object_size << page_size which
is not the case with isci_request objects and the dma_pool routines show
up in the top of the profile.

The old io_request_table which tracked whether tci slots were in-flight
or not is replaced with an IREQ_ACTIVE flag per request.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Combine three bools into one unsigned long 'flags'.  Doesn't increase the
request size due to packing. (to do: optimize the structure layout).
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

The tci_pool tracks our outstanding command slots which are also the 'index'
portion of our tags.  Grabbing the tag early in ->lldd_execute_task let's us
drop the isci_host_can_queue() and ->was_tag_assigned_by_user infrastructure.
->was_tag_assigned_by_user required the task context to be duplicated in
request-local buffer.  With the tci established early we can build the
task_context directly into its final location and skip a memcpy.

With the task context buffer at a known address at request construction we
have the opportunity/obligation to also fix sgl handling.  This rework feels
like it belongs in another patch but the sgl handling and task_context are too
intertwined.
1/ fix the 'ab' pair embedded in the task context to point to the 'cd' pair in
   the task context (previously we were prematurely linking to the staging
   buffer).
2/ fix the broken iteration of pio sgls that assumes all sgls are relative to
   the request, and does a dangerous looking reverse lookup of physical
   address to virtual address.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

When the remote device transitions to a not-ready state because of
an NCQ error condition, all outstanding requests to that device
are terminated and completed to libsas on the normal path.  The
device then waits for a READ LOG EXT command to issue on the task
management path.
Signed-off-by: NJeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

Updates to the frame_rcvd before need to be atomic with respect to when
they are evaluated by libsas.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

scu_index is a parameter of isci_parse_eom_parameters and is an index
in controller table. There is a check: scu_index > SCI_MAX_CONTROLLERS
which is insufficient and should be: scu_index >= SCI_MAX_CONTROLLERS.
scu_index is used as an index in the table which size is
SCI_MAX_CONTROLLERS.
Signed-off-by: NMaciej Patelczyk <maciej.patelczyk@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

1/ fix the timeout for wait_for_completion_timeout
2/ In the tmf timeout case we need to wait for our termination callback
3/ Once the request is successfully started it will be freed according to the
   normal lifetime for requests.
Signed-off-by: NDan Williams <dan.j.williams@intel.com>