When replaying interrupts (as a result of the interrupt occurring
while soft-disabled), in the case of the decrementer, we are exclusively
testing for a pending timer target. However we also use decrementer
interrupts to trigger the new "irq_work", which in this case would
be missed.

This change the logic to force a replay in both cases of a timer
boundary reached and a decrementer interrupt having actually occurred
while disabled. The former test is still useful to catch cases where
a CPU having been hard-disabled for a long time completely misses the
interrupt due to a decrementer rollover.

CC: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: NSteven Rostedt <rostedt@goodmis.org>

Normally, the kernel emulates a few instructions that are unimplemented
on some processors (e.g. the old dcba instruction), or privileged (e.g.
mfpvr).  The emulation of unimplemented instructions is currently not
working on the PowerNV platform.  The reason is that on these machines,
unimplemented and illegal instructions cause a hypervisor emulation
assist interrupt, rather than a program interrupt as on older CPUs.
Our vector for the emulation assist interrupt just calls
program_check_exception() directly, without setting the bit in SRR1
that indicates an illegal instruction interrupt.  This fixes it by
making the emulation assist interrupt set that bit before calling
program_check_interrupt().  With this, old programs that use no-longer
implemented instructions such as dcba now work again.

CC: <stable@vger.kernel.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

It's possible for us to crash when running with ftrace enabled, eg:

  Bad kernel stack pointer bffffd12 at c00000000000a454
  cpu 0x3: Vector: 300 (Data Access) at [c00000000ffe3d40]
      pc: c00000000000a454: resume_kernel+0x34/0x60
      lr: c00000000000335c: performance_monitor_common+0x15c/0x180
      sp: bffffd12
     msr: 8000000000001032
     dar: bffffd12
   dsisr: 42000000

If we look at current's stack (paca->__current->stack) we see it is
equal to c0000002ecab0000. Our stack is 16K, and comparing to
paca->kstack (c0000002ecab3e30) we can see that we have overflowed our
kernel stack. This leads to us writing over our struct thread_info, and
in this case we have corrupted thread_info->flags and set
_TIF_EMULATE_STACK_STORE.

Dumping the stack we see:

  3:mon> t c0000002ecab0000
  [c0000002ecab0000] c00000000002131c .performance_monitor_exception+0x5c/0x70
  [c0000002ecab0080] c00000000000335c performance_monitor_common+0x15c/0x180
  --- Exception: f01 (Performance Monitor) at c0000000000fb2ec .trace_hardirqs_off+0x1c/0x30
  [c0000002ecab0370] c00000000016fdb0 .trace_graph_entry+0xb0/0x280 (unreliable)
  [c0000002ecab0410] c00000000003d038 .prepare_ftrace_return+0x98/0x130
  [c0000002ecab04b0] c00000000000a920 .ftrace_graph_caller+0x14/0x28
  [c0000002ecab0520] c0000000000d6b58 .idle_cpu+0x18/0x90
  [c0000002ecab05a0] c00000000000a934 .return_to_handler+0x0/0x34
  [c0000002ecab0620] c00000000001e660 .timer_interrupt+0x160/0x300
  [c0000002ecab06d0] c0000000000025dc decrementer_common+0x15c/0x180
  --- Exception: 901 (Decrementer) at c0000000000104d4 .arch_local_irq_restore+0x74/0xa0
  [c0000002ecab09c0] c0000000000fe044 .trace_hardirqs_on+0x14/0x30 (unreliable)
  [c0000002ecab0fb0] c00000000016fe3c .trace_graph_entry+0x13c/0x280
  [c0000002ecab1050] c00000000003d038 .prepare_ftrace_return+0x98/0x130
  [c0000002ecab10f0] c00000000000a920 .ftrace_graph_caller+0x14/0x28
  [c0000002ecab1160] c0000000000161f0 .__ppc64_runlatch_on+0x10/0x40
  [c0000002ecab11d0] c00000000000a934 .return_to_handler+0x0/0x34
  --- Exception: 901 (Decrementer) at c0000000000104d4 .arch_local_irq_restore+0x74/0xa0

  ... and so on

__ppc64_runlatch_on() is called from RUNLATCH_ON in the exception entry
path. At that point the irq state is not consistent, ie. interrupts are
hard disabled (by the exception entry), but the paca soft-enabled flag
may be out of sync.

This leads to the local_irq_restore() in trace_graph_entry() actually
enabling interrupts, which we do not want. Because we have not yet
reprogrammed the decrementer we immediately take another decrementer
exception, and recurse.

The fix is twofold. Firstly make sure we call DISABLE_INTS before
calling RUNLATCH_ON. The badly named DISABLE_INTS actually reconciles
the irq state in the paca with the hardware, making it safe again to
call local_irq_save/restore().

Although that should be sufficient to fix the bug, we also mark the
runlatch routines as notrace. They are called very early in the
exception entry and we are asking for trouble tracing them. They are
also fairly uninteresting and tracing them just adds unnecessary
overhead.

[ This regression was introduced by fe1952fc
  "powerpc: Rework runlatch code" by myself --BenH
]

CC: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The stop machine logic can lock up if all but one of the migration
threads make it through the disable-irq step and the one remaining
thread gets stuck in __do_softirq.  The reason __do_softirq can hang is
that it has a bail-out based on jiffies timeout, but in the lockup case,
jiffies itself is not incremented.

To work around this, re-add the max_restart counter in __do_irq and stop
processing irqs after 10 restarts.

Thanks to Tejun Heo and Rusty Russell and others for helping me track
this down.

This was introduced in 3.9 by commit c10d7367 ("softirq: reduce
latencies").

It may be worth looking into ath9k to see if it has issues with its irq
handler at a later date.

The hang stack traces look something like this:

    ------------[ cut here ]------------
    WARNING: at kernel/watchdog.c:245 watchdog_overflow_callback+0x9c/0xa7()
    Watchdog detected hard LOCKUP on cpu 2
    Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
    Pid: 23, comm: migration/2 Tainted: G         C   3.9.4+ #11
    Call Trace:
     <NMI>   warn_slowpath_common+0x85/0x9f
      warn_slowpath_fmt+0x46/0x48
      watchdog_overflow_callback+0x9c/0xa7
      __perf_event_overflow+0x137/0x1cb
      perf_event_overflow+0x14/0x16
      intel_pmu_handle_irq+0x2dc/0x359
      perf_event_nmi_handler+0x19/0x1b
      nmi_handle+0x7f/0xc2
      do_nmi+0xbc/0x304
      end_repeat_nmi+0x1e/0x2e
     <<EOE>>
      cpu_stopper_thread+0xae/0x162
      smpboot_thread_fn+0x258/0x260
      kthread+0xc7/0xcf
      ret_from_fork+0x7c/0xb0
    ---[ end trace 4947dfa9b0a4cec3 ]---
    BUG: soft lockup - CPU#1 stuck for 22s! [migration/1:17]
    Modules linked in: ath9k ath9k_common ath9k_hw ath mac80211 cfg80211 nfsv4 auth_rpcgss nfs fscache nf_nat_ipv4 nf_nat veth 8021q garp stp mrp llc pktgen lockd sunrpc]
    irq event stamp: 835637905
    hardirqs last  enabled at (835637904): __do_softirq+0x9f/0x257
    hardirqs last disabled at (835637905): apic_timer_interrupt+0x6d/0x80
    softirqs last  enabled at (5654720): __do_softirq+0x1ff/0x257
    softirqs last disabled at (5654725): irq_exit+0x5f/0xbb
    CPU 1
    Pid: 17, comm: migration/1 Tainted: G        WC   3.9.4+ #11 To be filled by O.E.M. To be filled by O.E.M./To be filled by O.E.M.
    RIP: tasklet_hi_action+0xf0/0xf0
    Process migration/1
    Call Trace:
     <IRQ>
      __do_softirq+0x117/0x257
      irq_exit+0x5f/0xbb
      smp_apic_timer_interrupt+0x8a/0x98
      apic_timer_interrupt+0x72/0x80
     <EOI>
      printk+0x4d/0x4f
      stop_machine_cpu_stop+0x22c/0x274
      cpu_stopper_thread+0xae/0x162
      smpboot_thread_fn+0x258/0x260
      kthread+0xc7/0xcf
      ret_from_fork+0x7c/0xb0
Signed-off-by: NBen Greear <greearb@candelatech.com>
Acked-by: NTejun Heo <tj@kernel.org>
Acked-by: NPekka Riikonen <priikone@iki.fi>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull net/9p bug fix from Eric Van Hensbergen:
 "zero copy error fix"

* tag '9p-3.10-bug-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  net/9p: Handle error in zero copy request correctly for 9p2000.u

Pull spi fixes from Mark Brown:
 "A few nasty issues, particularly a race with the interrupt controller
  in the xilinx driver, together with a couple of more minor fixes and a
  much needed move of the mailing list away from sourceforge."

* tag 'spi-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: hspi: fixup long delay time
  spi: spi-xilinx: Remove ISR race condition
  spi: topcliff-pch: fix error return code in pch_spi_probe()
  spi: topcliff-pch: Pass correct pointer to free_irq()
  spi: Move mailing list to vger

Merge tag 'stable/for-linus-3.10-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen

Pull xen fixes from Konrad Rzeszutek Wilk:
 "Two bug-fixes for regressions:
   - xen/tmem stopped working after a certain combination of
     modprobe/swapon was used
   - cpu online/offlining would trigger WARN_ON."

* tag 'stable/for-linus-3.10-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
  xen/tmem: Don't over-write tmem_frontswap_poolid after tmem_frontswap_init set it.
  xen/smp: Fixup NOHZ per cpu data when onlining an offline CPU.

Pull regmap fixes from Mark Brown:
 "The biggest fix here is Lars-Peter's fix for custom locking callbacks
  which is pretty localised but important for those devices that use the
  feature.  Otherwise we've got a couple of fairly small cleanups which
  would have been sent sooner were it not for letting Lars-Peter's patch
  soak for a while"

* tag 'regmap-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
  regmap: rbtree: Fixed node range check on sync
  regmap: regcache: Fixup locking for custom lock callbacks
  regmap: debugfs: Check return value of regmap_write()

Pull crypto fixes from Herbert Xu:
 "This fixes a build problem in sahara and temporarily disables two new
  optimisations because of performance regressions until a permanent fix
  is ready"

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: sahara - fix building as module
  crypto: blowfish - disable AVX2 implementation
  crypto: twofish - disable AVX2 implementation

Commit 10a7a077 ("xen: tmem: enable Xen
tmem shim to be built/loaded as a module") allows the tmem module
to be loaded any time. For this work the frontswap API had to
be able to asynchronously to call tmem_frontswap_init before
or after the swap image had been set. That was added in git
commit 905cd0e1
("mm: frontswap: lazy initialization to allow tmem backends to build/run as modules").

Which means we could do this (The common case):

 modprobe tmem		[so calls frontswap_register_ops, no ->init]
			 modifies tmem_frontswap_poolid = -1
 swapon /dev/xvda1	[__frontswap_init, calls -> init, tmem_frontswap_poolid is
			 < 0 so tmem hypercall done]

Or the failing one:

 swapon /dev/xvda1	[calls __frontswap_init, sets the need_init bitmap]
 modprobe tmem		[calls frontswap_register_ops, -->init calls, finds out
			tmem_frontswap_poolid is 0, does not make a hypercall.
			Later in the module_init, sets tmem_frontswap_poolid=-1]

Which meant that in the failing case we would not call the hypercall
to initialize the pool and never be able to make any frontswap
backend calls.

Moving the frontswap_register_ops after setting the tmem_frontswap_poolid
fixes it.
Signed-off-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: NBob Liu <bob.liu@oracle.com>

Pull powerpc fixes from Benjamin Herrenschmidt:
 "This is purely regressions (though not all recent ones) or stable
  material"

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Partial revert of "Context switch more PMU related SPRs"
  powerpc/perf: Fix deadlock caused by calling printk() in PMU exception
  powerpc/hw_breakpoints: Add DABRX cpu feature to fix 32-bit regression
  powerpc/power8: Update denormalization handler
  powerpc/pseries: Simplify denormalization handler
  powerpc/power8: Fix oprofile and perf
  powerpc/eeh: Don't check RTAS token to get PE addr
  powerpc/pci: Check the bus address instead of resource address in pcibios_fixup_resources

Pull ARM fixes from Russell King:
 "The biggest two fixes are fixing a compilation error with the
  decompressor, and a problem with our __my_cpu_offset implementation.

  Other changes are very trivial and small, which seems to be the way
  for most -rc stuff."

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7747/1: pcpu: ensure __my_cpu_offset cannot be re-ordered across barrier()
  ARM: 7750/1: update legacy CPU ID in decompressor cache support jump table
  ARM: 7743/1: compressed/head.S: work around new binutils warning
  ARM: 7742/1: topology: export cpu_topology
  ARM: 7737/1: fix kernel decompressor compilation error with CONFIG_DEBUG_SEMIHOSTING

In commit 59affcd3 I added context switching of more PMU SPRs, because
they are potentially exposed to userspace on Power8. However despite me
being a smart arse in the commit message it's actually not correct. In
particular it interacts badly with a global perf record.

We will have to do something more complicated, but that will have to
wait for 3.11.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In commit bc09c219 "Fix finding overflowed PMC in interrupt" we added
a printk() to the PMU exception handler. Unfortunately that is not safe.

The problem is that the PMU exception may run even when interrupts are
soft disabled, aka NMI context. We do this so that we can profile parts
of the kernel that have interrupts soft-disabled.

But by calling printk() from the exception handler, we can potentially
deadlock in the printk code on logbuf_lock, eg:

  [c00000038ba575c0] c000000000081928 .vprintk_emit+0xa8/0x540
  [c00000038ba576a0] c0000000007bcde8 .printk+0x48/0x58
  [c00000038ba57710] c000000000076504 .perf_event_interrupt+0x2d4/0x490
  [c00000038ba57810] c00000000001f6f8 .performance_monitor_exception+0x48/0x60
  [c00000038ba57880] c0000000000032cc performance_monitor_common+0x14c/0x180
  --- Exception: f01 (Performance Monitor) at c0000000007b25d4 ._raw_spin_lock_irq
  +0x64/0xc0
  [c00000038ba57bf0] c00000000007ed90 .devkmsg_read+0xd0/0x5a0
  [c00000038ba57d00] c0000000001c2934 .vfs_read+0xc4/0x1e0
  [c00000038ba57d90] c0000000001c2cd8 .SyS_read+0x58/0xd0
  [c00000038ba57e30] c000000000009d54 syscall_exit+0x0/0x98
  --- Exception: c01 (System Call) at 00001fffffbf6f7c
  SP (3ffff6d4de10) is in userspace

Fix it by making sure we only call printk() when we are not in NMI
context.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Cc: <stable@vger.kernel.org> # 3.9
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

When introducing support for DABRX in 4474ef05, we broke older 32-bit CPUs
that don't have that register.

Some CPUs have a DABR but not DABRX.  Configuration are:
- No 32bit CPUs have DABRX but some have DABR.
- POWER4+ and below have the DABR but no DABRX.
- 970 and POWER5 and above have DABR and DABRX.
- POWER8 has DAWR, hence no DABRX.

This introduces CPU_FTR_DABRX and sets it on appropriate CPUs.  We use
the top 64 bits for CPU FTR bits since only 64 bit CPUs have this.

Processors that don't have the DABRX will still work as they will fall
back to software filtering these breakpoints via perf_exclude_event().
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Reported-by: N"Gorelik, Jacob (335F)" <jacob.gorelik@jpl.nasa.gov>
cc: stable@vger.kernel.org (v3.9 only)
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

POWER8 can take a denormalisation exception on any VSX registers.

This does the extra 32 VSX registers we don't currently handle.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The following simplifies the denorm code by using macros to generate the long
stream of almost identical instructions.

This patch results in no changes to the output binary, but removes a lot of
lines of code.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

In 2ac6f427 powerpc/cputable: Fix oprofile_cpu_type on power8
we broke all power8 hw events.

This reverts this change and uses oprofile_type instead. Perf now works
on POWER8 again and oprofile will revert to using timers on POWER8.

Kudos to mpe this fix.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

RTAS token "ibm,get-config-addr-info" or ibm,get-config-addr-info2"
are used to retrieve the PE address according to PCI address, which
made up of domain/bus/slot/function. If we don't have those 2 tokens,
the domain/bus/slot/function would be used as the address for EEH
RTAS operations. Some older f/w might not have those 2 tokens and
that blocks the EEH functionality to be initialized. It was introduced
by commit e2af155c ("powerpc/eeh: pseries platform EEH initialization").

The patch skips the check on those 2 tokens so we can bring up EEH
functionality successfully. And domain/bus/slot/function will be
used as address for EEH RTAS operations.

Cc: <stable@vger.kernel.org> # v3.4+
Reported-by: NRobert Knight <knight@princeton.edu>
Signed-off-by: NGavin Shan <shangw@linux.vnet.ibm.com>
Tested-by: NRobert Knight <knight@princeton.edu>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If a BAR has the value of 0, we would assume that it is unset yet and
then mark the resource as unset and would reassign it later. But after
commit 6c5705fe (powerpc/PCI: get rid of device resource fixups)
the pcibios_fixup_resources is invoked after the bus address was
translated to linux resource. So the value of res->start is resource
address. And since the resource and bus address may be different, we
should translate it to the bus address before doing the check.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Pull hwmon fix from Guenter Roeck:
 "Improve chip detection in ADM1021 driver to avoid misdetections

  This is not a critical patch, but one we'll want to have applied to
  -stable, since the misdetection especially of LM84 has been causing
  trouble for quite some time."

* tag 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (adm1021) Strengthen chip detection for ADM1021, LM84 and MAX1617

This patch fixes warnings due to missing lock on write error path.

  WARNING: at fs/hpfs/hpfs_fn.h:353 hpfs_truncate+0x75/0x80 [hpfs]()
  Hardware name: empty
  Pid: 26563, comm: dd Tainted: P           O 3.9.4 #12
  Call Trace:
    hpfs_truncate+0x75/0x80 [hpfs]
    hpfs_write_begin+0x84/0x90 [hpfs]
    _hpfs_bmap+0x10/0x10 [hpfs]
    generic_file_buffered_write+0x121/0x2c0
    __generic_file_aio_write+0x1c7/0x3f0
    generic_file_aio_write+0x7c/0x100
    do_sync_write+0x98/0xd0
    hpfs_file_write+0xd/0x50 [hpfs]
    vfs_write+0xa2/0x160
    sys_write+0x51/0xa0
    page_fault+0x22/0x30
    system_call_fastpath+0x1a/0x1f
Signed-off-by: NMikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org  # 2.6.39+
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:

 - Trivial: unused variable removal

 - Posix-timers: Add the clock ID to the new proc interface to make it
   useful.  The interface is new and should be functional when we reach
   the final 3.10 release.

 - Cure a false positive warning in the tick code introduced by the
   overhaul in 3.10

 - Fix for a persistent clock detection regression introduced in this
   cycle

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Correct run-time detection of persistent_clock.
  ntp: Remove unused variable flags in __hardpps
  posix-timers: Show clock ID in proc file
  tick: Cure broadcast false positive pending bit warning

Pull irqdomain bug fixes from Grant Likely:
 "This branch contains a set of straight forward bug fixes to the
  irqdomain code and to a couple of drivers that make use of it."

* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
  irqchip: Return -EPERM for reserved IRQs
  irqdomain: document the simple domain first_irq
  kernel/irq/irqdomain.c: before use 'irq_data', need check it whether valid.
  irqdomain: export irq_domain_add_simple

The irqdomain core will report a log message for any attempted map call
that fails unless the error code is -EPERM. This patch changes the
Versatile irq controller drivers to use -EPERM because it is normal for
a subset of the IRQ inputs to be marked as reserved on the various
Versatile platforms.
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

Since irq_data may be NULL, if so, we WARN_ON(), and continue, 'hwirq'
which related with 'irq_data' has to initialize later, or it will cause
issue.
Signed-off-by: NChen Gang <gang.chen@asianux.com>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:

ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-rcar.ko] undefined!
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-em.ko] undefined!
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "Another week, another batch of fixes for arm-soc platforms.

  Nothing controversial here, a handful of fixes for regressions and/or
  serious problems across several of the platforms.  Things are slowing
  down nicely on fix rates for 3.10"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: exynos: add debug_ll_io_init() call in exynos_init_io()
  ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is defined
  ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
  sh-pfc: r8a7779: Don't group USB OVC and PENC pins
  ARM: mxs: icoll: Fix interrupts gpio bank 0
  ARM: imx: clk-imx6q: AXI clock select index is incorrect
  ARM: bcm2835: override the HW UART periphid
  ARM: mvebu: Fix bug in coherency fabric low level init function
  ARM: Kirkwood: TS219: Fix crash by double PCIe instantiation
  ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3
  ARM: ux500: Only configure wake-up reasons on ux500 based platforms
  ARM: dts: imx: fix clocks for cspi
  ARM i.MX6q: fix for ldb_di_sels

Pull MIPS fixes from Ralf Baechle:
 "MIPS fixes across the field.  The only area that's standing out is the
  exception handling which received it's dose of breakage as part of the
  microMIPS patchset"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: add missing SZ_1M multiplier
  MIPS: Compat: Fix cputime_to_timeval() arguments in compat binfmt_elf.
  MIPS: OCTEON: Improve _machine_halt implementation.
  MIPS: rtlx: Fix implicit declaration of function set_vi_handler()
  MIPS: Trap exception handling fixes
  MIPS: Quit exposing Kconfig symbols in uapi headers.
  MIPS: Remove duplicate definition of check_for_high_segbits.

Pull m68knommu fix from Greg Ungerer:
 "A single fix for compilation breakage to many of the ColdFire CPU
  targets"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: only use local gpio_request_one if not using GPIOLIB

Pull drm fixes from Dave Airlie:
 "Regression fixers for the big 3:

   - nouveau: hdmi audio, dac load detect, s/r regressions fixed
   - radeon: long standing system hang fixed, hdmi audio and rs780 fast
     fb fixes
   - intel: one old regression, a WARN removal, and a stop X dying fix

  Otherwise one mgag200 fix, a couple of arm build fixes, and a core use
  after free fix."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nv50/kms: use dac loadval from vbios, where it's available
  drm/nv50/disp: force dac power state during load detect
  drm/nv50-nv84/fifo: fix resume regression introduced by playlist race fix
  drm/nv84/disp: Fix HDMI audio regression
  drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC.
  drm/radeon: don't allow audio on DCE6
  drm/radeon: Use direct mapping for fast fb access on RS780/RS880 (v2)
  radeon: Fix system hang issue when using KMS with older cards
  drm/i915: no lvds quirk for hp t5740
  drm/i915: Quirk the pipe A quirk in the modeset state checker
  drm/i915: Fix spurious -EIO/SIGBUS on wedged gpus
  drm/mgag200: Add missing write to index before accessing data register
  drm/nouveau: use mdelay instead of large udelay constants
  drm/tilcd: select BACKLIGHT_LCD_SUPPORT
  drm: fix a use-after-free when GPU acceleration disabled

Pull slave-dmaengine fixes from Vinod Koul:
 "Fix from Andy is for dmatest regression reported by Will and Rabin has
  fixed runtime ref counting for st_dma40"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmatest: do not allow to interrupt ongoing tests
  dmaengine: ste_dma40: fix pm runtime ref counting

Merge tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "This contains 4 fixes.

  The first two fix the case where full RCU debugging is enabled,
  enabling function tracing causes a live lock of the system.  This is
  due to the added debug checks in rcu_dereference_raw() that is used by
  the function tracer.  These checks are also traced by the function
  tracer as well as cause enough overhead to the function tracer to slow
  down the system enough that the time to finish an interrupt can take
  longer than when the next interrupt is triggered, causing a live lock
  from the timer interrupt.

  Talking this over with Paul McKenney, we came up with a fix that adds
  a new rcu_dereference_raw_notrace() that does not perform these added
  checks, and let the function tracer use that.

  The third commit fixes a failed compile when branch tracing is
  enabled, due to the conversion of the trace_test_buffer() selftest
  that the branch trace wasn't converted for.

  The forth patch fixes a bug caught by the RCU lockdep code where a
  rcu_read_lock() is performed when rcu is disabled (either going to or
  from idle, or user space).  This happened on the irqsoff tracer as it
  calls task_uid().  The fix here was to use current_uid() when possible
  that doesn't use rcu locking.  Which luckily, is always used when
  irqsoff calls this code."

* tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Use current_uid() for critical time tracing
  tracing: Fix bad parameter passed in branch selftest
  ftrace: Use the rcu _notrace variants for rcu_dereference_raw() and friends
  rcu: Add _notrace variation of rcu_dereference_raw() and hlist_for_each_entry_rcu()

Commit 9f29ab11 ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600.  Tony says:

  "It panics with the message:

   Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel

   [...] my problem comes from arch/ia64/hp/common/sba_iommu.c
   where the code in sba_init() says:

        acpi_bus_register_driver(&acpi_sba_ioc_driver);
        if (!ioc_list) {

   but because of this change we never managed to call ioc_init()
   so ioc_list doesn't get set up, and we die."

Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: NTony Luck <tony.luck@gmail.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

From Shawn Guo, mxs fixes for 3.10:

- Since the time we move to MULTI_IRQ_HANDLER, the 0x7f polling for no
  interrupt in icoll_handle_irq() becomes insane, because 0x7f is an
  valid interrupt number, the irq of gpio bank 0.  That unnecessary
  polling results in the driver not detecting when irq 0x7f is active
  which makes the machine effectively dead lock.  The fix removes the
  interrupt poll loop and allows usage of gpio0 interrupt without an
  infinite loop.

* tag 'mxs-fixes-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs: icoll: Fix interrupts gpio bank 0
Signed-off-by: NOlof Johansson <olof@lixom.net>

From Shawn Guo, imx fixes for 3.10, take 2:

- One device tree fix for all spi node to have per clock added.
  The clock is needed by spi driver to calculate bit rate divisor.
  The spi node in the current device trees either does not have the
  clock or is defined as dummy clock, in which case the driver probe
  will fail or spi will run at a wrong bit rate.

- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.

* tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx: clk-imx6q: AXI clock select index is incorrect
  ARM: dts: imx: fix clocks for cspi
  ARM i.MX6q: fix for ldb_di_sels
Signed-off-by: NOlof Johansson <olof@lixom.net>

If the early MMU mapping of the UART happens to get booted out of the
TLB between the start of paging_init() and when we finally re-add the
UART at the very end of s3c_init_cpu(), we'll get a hang at bootup if
we've got early_printk enabled.  Avoid this hang by calling
debug_ll_io_init() early.

Without this patch, you can reliably reproduce a hang when early
printk is enabled by adding flush_tlb_all() at the start of
exynos_init_io().  After this patch the hang goes away.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes

From Simon Horman, Renesas ARM based SoC fixes for v3.10:
- Correction to USB OVC and PENC pin groupings on r8a7779 SoC.
  This avoids conflicts when the USB_OVCn pins are used by another function.
  This has been observed to be a problem in v3.10-rc1.
- Update CMT clock rating for sh73a0 SoC to resolve boot failure
  on kzm9g-reference. This resolves a regression between v3.9 and v3.10-rc1.

* tag 'renesas-fixes-for-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
  ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
  sh-pfc: r8a7779: Don't group USB OVC and PENC pins
Signed-off-by: NOlof Johansson <olof@lixom.net>