regulator smps123 supply from Palmas PMIC powers CPU0 on DRA7 EVM.

[nm@ti.com: rebase to latest]
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NJ Keerthy <j-keerthy@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

regulator smps123 supply from Palmas PMIC powers CPU0 on OMAP5uEVM.

Based on a patch by J Keerthy <j-keerthy@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Correct mcspi pin descriptions to match corresponding node name and
add chip select number to be consistent with OMAP5 TRM.
Signed-off-by: NEric Witcher <ewitcher@mindspring.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Control module is not usb specific.
Changes the label to usb_ctrl_mod.
Signed-off-by: NMarkus Pargmann <mpa@pengutronix.de>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

NanoBone Specification:
-----------------------
CPU:
  TI AM335x

Memory:
  256MB DDR3
  128MB NOR flash
  128KB FRAM

Ethernet:
  2 x 10/100 connected to SMSC LAN8710 PHY

USB:
  1 x USB2.0 Type A

I2C:
  2Kbit EEPROM (Microchip 24AA02)
  RTC (Maxim DS1338)
  GPIO Expander (Microchip MCP23017)

Expansion connector:
  6 x UART
  1 x MMC/SD
  1 x USB2.0
Signed-off-by: NMark Jackson <mpfj@newflow.co.uk>
Reviewed-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Provide alias to allow ordering the i2c devices correctly.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Currently, on OMAP5, i2c1 and i2c5 defer probe due to pinctrl
dependencies. This changes the i2c ID each bus is registered with in
i2c-dev interface. As a result of this, many userspace tools break and
there is no consistent manner to fix the same if the i2c dev interface
have no consistent numbering.

Since this could happen for other OMAP derivatives, provide i2c alias
for all OMAP3+ SoCs to allow ordering the i2c devices correctly.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add mmc1 dt node to IGEP COM AQUILA board.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add nodes for McASP0 and McASP1 for AM43xx.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.

Fixes USB OTG port on beagle after the Generic PHY framework was
merged in greg/usb-next. [1]

[1] - https://lkml.org/lkml/2013/9/27/581Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

AM335x EVM-SK have only support for audio playback (stereo jack on the
board) via tlv320aic3106 codec connected to McASP1.
Enable the support for audio playback on the board:
- McASP1 configuration
- tlv320aic3106 configuration
- Machine driver.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Adds sound, tlv320aic3106, mcasp1, and am335x_evm_audio_pin nodes.
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This patch adds a second tuple to reg property. The new property tuple
describes the memory location for data port registers mapped trough
L3 bus on am33xx. The both property tuples are named accordingly in
the reg-names property.
Signed-off-by: NHebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add missing mcasp entries in the am33xx.dtsi include file.
Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NJyri Sarha <jsarha@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

-> Adding pinmux for cpsw, i2c0.
-> Enabling the modules that are present in AM4372 EPOS EVM
These modules are tested on AM4372 EPOS EVM.
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Populate nodes for l2-cache-controller, EDMA, mailbox,
mmc, sham.

Update as well DT properties for epwmss, aes, des.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: NLokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Added dr_mode property in dwc3 and set its default mode to device.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

smps10 should be enabled only in the case of host mode. So stop
doing always_on, boot_on from smps10_out1. The driver will enable
it in host mode.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
supplies VDD_MPU.

Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
MPU voltage switches over to VSET0 voltage value (boot voltage) which
is not sufficient to operate the device at OPP100.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Do not reset GPIO0 at  boot-up because GPIO0 is used
on AM335x EVM-SK to control VTT regulators on DDR3.

Without this EVM-SK boards fail to boot-up because
of DDR3 corruption.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

On OMAP we have co-processor IPs, memory controllers,
GPIOs which control regulators and power switches to
PMIC, and SoC internal Bus IPs, some or most of which
should either not be reset or idled or both at init.
(In some cases there are erratas which prevent an IP
from being reset)
Have a way to pass this information from DT.

Update the am33xx/omap4 and omap5 dtsi files with the
new bindings for modules which either should not be
idled. reset or both. A later patch would cleanup the
same information that exists today as part of the hwmod
data files.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The generic PHY framewrok expects different properties than the
old USB PHY framework. Supply those properties.

Fixes USB OTG port on GAT04 and N900 after the Generic PHY framework was
merged in greg/usb-next. [1]

[1] - https://lkml.org/lkml/2013/9/27/581Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

The arm arch timers frequency are now programmed in the CNTFREQ
per-cpu register by the timer code using the secure API [1].
So remove the redundant entry from the dts.

[1] http://marc.info/?l=linux-omap&m=138139106312786&w=2Signed-off-by: NSricharan R <r.sricharan@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add mmc2 dt node to dra7-evm board
and model eMMC vcc as fixed regulator.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add mmc1 dt node to dra7-evm board.
Input for ldo1 regulator is controlled by gpio 5 of pcf8575 chip (0x21)
on i2c1 bus. When dt support for gpio-pcf857x is available, input supply
will be modelled as cascaded regulator.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

This allows the palmas pm_power_off to kick in on power off command
and switch off the board.
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Commit 840ef8b7 ("ARM: dt: add header to define IRQ flags") added
constants for IRQ edge/level triggered types so use it instead of
a magic number to enhance the DT readability.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add device nodes for the HS USB Host port 1, USB PHY and its
required regulator and also pin mux setup for HS USB1 pins.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Commit ad871c10 ("ARM: dts: OMAP: Add usb_otg and glue data to O
added USB OTG support for most OMAP boards but some OMAP3 boards
such as IGEP boards were not updated. This patch adds an USB OTG
device node to these board.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Enable the hdmi output and the LCD Controller on BeagleBone
Black. Also configure the correct pinmux for output of
video data from the SoC to the HDMI encoder.
Signed-off-by: NDarren Etheridge <detheridge@ti.com>
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add LCDC device node in DT for am33xx
Add LCDC and Panel info in DT for am335x-evm

Changes:
- remove redundant/unnecessary SoC specific setting in the board dts
- resolved conflicts on for_3.13/dts
Signed-off-by: NBenoit Parrot <bparrot@ti.com>
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

AM437x SoC has a DES3DES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

AM437x SoC has AES module similar to the one on OMAP4.
Add DT node for the same.
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

AES interrupts were previously not used, but after recent changes
to omap-aes driver, its being used.
Correct the interrupt number to have working PIO mode.
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add the generic AM33XX AES module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms.  Also add Documentation file describing the data
for the AES module.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NJoel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Add the generic AM33XX SHAM module's device tree data and
enable it for the am335x-evm, am335x-evmsk, and am335x-bone
platforms.  Also add Documentation file describing the data
for the SHAM module.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: NMark A. Greer <mgreer@animalcreek.com>
Signed-off-by: NJoel Fernandes <joelf@ti.com>
[joelf@ti.com: Dropped interrupt-parent property, documentation fixups]
Acked-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

OMAP4 has an DES3DES  module that uses the omap-des crypto driver.
Add DT entries for the same.
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

OMAP4 has an AES module that uses the omap-aes crypto driver.
Add DT entries for the same.
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Set bus-width to make SD card operate in 4 bit mode.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>

Set pinmux_emmc_pins mux mode for cmd line to MODE2 in order
to detect eMMC on BBB and BBW + eMMC cape.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Tested-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NBenoit Cousson <bcousson@baylibre.com>