This patch replace monitor/recover timer by watchdog based on time
stamp. New code allow to discover hangs more precisely.

Timeout values are currently doubled monitoring period values of
previous timer. This have to be tuned based of firmware timing
capabilities.

Tested on 3945, 4965, 5300, 6300.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Change the module parameter name to bt_ch_inhibition from
bt_ch_announce to better describe the functionality

In order to allow Bluetooth to activate a smart AFH mechanism
and to maximize its available bandwidth the WiFi will request
BT Core to inhibit its activity in channels that interfere
with WiFi activity (and vice versa) if bt_ch_inhibition is enabled

Set module parameter "bt_ch_inhibition=0" will disable the channel
inhibition function
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Give the corresponding name for .cfg data structure
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Our hardware has reliable TX status, but we're
not currently advertising that to mac80211.
Since the packet loss monitoring will depend
on it, advertise it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Have the STATUS_READY bit set before commit_rxon call to avoid fail
to send tx power to uCode.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

When setting rxon chain and filter, no need to commit RXON when the
chain flag is not changed. This reduces the number of RXON commands
we send down to uCode.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

EEPROM contain the SKU information for the device, use it.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Use dynamic aggregation threshold if bt traffic load is high
to reduce the impact on aggregated frame.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

There were two type of isr supported by iwlwifi devices.
  legacy isr - only used by legacy devices (3945 & 4965)
  ict isr - used by all new generation of iwlwifi devices

Move all the isr related functions into ops, the ict type of isr
supports only needed for newer devices.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When building 4965 without 5000+ there were a
lot of build errors due to functions being used
that weren't even compiled in. To fix this move
some code around and only compile the HCMD code
for 5000+ series as it's not used for 4965.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the supported PCI ID list for 100 series devices
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the supported PCI ID list for 6000g2a series devices
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update the supported PCI ID list for 6000g2b series devices
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Implement switching the interface while an
interface is up in iwlwifi. Interfaces have
to stay on the context they were created on.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to simplify the flow, and make new
enhancements easier, separate out the RXON
processing for modern AGN (5000 and newer)
from RXON processing for the older 3945 and
4965 devices. Avoid changing these old ones
to avoid regressions and move their code to
a new file (iwl-legacy.c). 4965 gets the
commit_rxon that used to be common for all
AGN devices, but with removed PAN support.

The new RXON processing is more central and
does more work in committing, so that it is
easier to follow.

To make it more evident what is split out
for legacy, split the necessary operations
for that into a new struct iwl_legacy_ops.
Those parts that still exist in the new AGN
code don't need to be parametrized.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Resending RXON timing here caused issues with
dual-mode under certain circumstances, so avoid
doing it here right now.

This effectively reverts b01efe43
and partially 2491fa42. The next
patch will make all this cleaner for just the
devices that need it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the future, 4965 and modern AGN devices will
need to have different mac80211 callbacks since
they have different capabilities. Prepare for
that by making the mac80211 operations a device
config.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the new PCI PM and let the PCI core code handle the PCI-specific
details of power transitions.

Based on similarly titled ath9k patch posted by Rafael J. Wysocki.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Acked-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Almost anywhere in the code we avoid committing rxon while performing
scan, and make rxon commit when scan complete. However in some places
in the code we do not follow that rule. This patch fix that problem in
iwlagn_configure_filter().

Since we do not commit directly in iwl3945_configure_filter, we can
also do the same for agn, so I just remove iwlcore_commit_rxon()
function and add a comment. Also change comment for iwl3945.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

According to comment in iwl_bg_scan_completed, setting tx power should
be deferred during pending scan, but we are not doing this.

This patch change code to really defer setting tx power after scan
complete. Additionally refactor iwl_set_tx_power code and call
lib->send_tx_power() directly from iwlagn_commit_rxon.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the beacon_skb is NULL, we might still
attempt to use it in this code path (if we
ever get here) -- make the code a bit more
defensive and check the return value of
iwl_fill_beacon_frame() against zero.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

There's no need to check for NULL before
calling dev_kfree_skb() since it is valid
to call it on NULL -- it becomes a no-op.

There's also no need to initialise the
beacon_skb variable to NULL just after
the memory it is in has been kzalloc'ed.

Some minor whitespace cleanups, and a
lock assertion in a function that needs
the mutex (to access the beacon_skb var)
complete the patch.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since we're also going to support AP (GO) mode,
the variable isn't used for just IBSS beacons
any more -- rename it to not mislead readers.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For WiFi/BT combo devices, priority table always need to download
before perform any calibration operation.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For advance BT/WiFi co-exist, always download bt priority table
before sending bt_config command
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

iwlagn driver uses the IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE
as the chain noise reset calibration index and
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE+1 as the chain noise gain
calibration index, if not specified by the TLV value in the new
firmware format.

However, this is broken if we need to add more calibrations like
the temperature offset calibration because we increased
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE by 1.

To fix this issue, define IWL_DEFAULT_STANDARD_PHY_CALIBRATE_TBL_SIZE
and use it as the calibration index instead. We still keep the
IWL_MAX_STANDARD_PHY_CALIBRATE_TBL_SIZE as a sanity check for
the TLV value given by ucode.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

For experimental uCode, it should work with the driver
if driver has experimental uCode support option enabled;
remove the API version checking.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

A number of declarations in iwl-core.h should
be in agn specific files, and also rename the
iwl-calib.h file to iwl-agn-calib.h to better
reflect that it belongs to agn.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since all devices share the same operation here,
there's no need to call it indirectly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The set_pwr_src operation is only ever used from
within the same sub-driver that it is declared
in, so it can just be called directly instead of
being an operation. Also, it is never called to
set the power source to V_aux, so change the two
functions accordingly (but keep the V_aux code
for documentation purposes in a comment).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

By duplicating a little bit of code between 3945
and agn, we can move a lot of code into an agn
specific station management file and thus reduce
the amount of code in core that is dead to 3945.

before:
   text	   data	    bss	    dec	    hex	filename
 212886	   3872	     96	 216854	  34f16	iwlcore.ko
 620542	  10448	    304	 631294	  9a1fe	iwlagn.ko
 314013	   3264	    196	 317473	  4d821	iwl3945.ko

after:
   text	   data	    bss	    dec	    hex	filename
 202857	   3872	     92	 206821	  327e5	iwlcore.ko
 629102	  10448	    308	 639858	  9c372	iwlagn.ko
 314240	   3264	    196	 317700	  4d904	iwl3945.ko

delta:
 -10029   iwlcore.ko
   8560   iwlagn.ko
    227   iwl3945.ko

so it's a net win even if you have both loaded,
likely because a lot of EXPORT_SYMBOLs go away.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

iwl_commit_rxon really should be named
iwlagn_commit_rxon, so rename it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

add new structures and defines need to identify 130 devices.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

move paramater definitions to a device paramater structure only
leaving the device name, which antennas are used and what firmware
file to use in the iwl_cfg structure.  this will not completely
remove the redundancies but greatly reduce them for devices that
only vary by name or antennas.  the parameters that are more
likely to change within a given device family are left in iwl_cfg.
also separate bt param structure added to help reduce more.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Hardware scan is the prefer method for all iwlwifi devices;
especially for dual-mode functions. Schedule to deprecate the
software scan support in kernel 2.6.40
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since uCode is responsible for doing DC calibration, there's no need
to let init uCode to do initial DC calibration then send results
back to driver, then driver sends the results to runtime uCode.
Driver can simply tell runtime uCode to do DC calibration.

Actually, this patch does not disable DC calib for init uCode. It just
prevent driver from saving and sending the DC calib results (from init
ucode) to runtime uCode. The driver still uses 0xffffffff in
CALIB_CFG_CMD for init ucode.
Signed-off-by: NShanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

add new structures and defines need to identify 100 devices.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Currently we force scan complete at the end of iwl_scan_cancel_timeout
function. This cause race condition when we can get a new scan request
from mac80211 and complete it by iwl_bg_complete from older scan. Change
code to force scan complete only when really needed: device goes down,
interface is removed or scan timeout occurs.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Always cancel scan when stooping device and scan is currently pending,
we should newer have scan running after down device.

To assure we start scan cancel from restart work we have to schedule
abort_scan to different workqueue than priv->workqueue.

Patch fix not cancel scanning when restarting firmware, what is
one of the causes of wdev_cleanup_work warning (together with permanent
network connection lost) reported at
https://bugzilla.redhat.com/show_bug.cgi?id=593566Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NWey-Yi W Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clear the "start calib" flag only for new association,
The flag will be set in post_associate function to trigger
the runtime calibration. Set this flag to "0" will stop the
runtime sensitivity calibration
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>