Signed-off-by: NEdward Lu <elu@qca.qualcomm.com>
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NEdward Lu <elu@qca.qualcomm.com>
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use WMI_TX_STATUS_EVENTID event to generate cfg80211_mgmt_tx_frame()
calls. Since we support only a single pending frame for now, use the
hardcoded cookie value 1 and store a copy of the pending frame in
the driver.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NEdward Lu <elu@qca.qualcomm.com>
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The target is not ready to accept addkey commands until the connect
event has been delivered, so delay these operations for the initial GTK.
In addition, properly set interface connected and mark netdev ready when
the AP mode setup has been completed.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Need to use correct length field for association request frame and
parse the IEs to find WPA/WPS/RSN IE. In addition, copying of the
IE better make sure it fits in into the buffer to avoid buffer
overflows.

In addition, add the (Re)AssocReq IEs to the cfg80211 new station
event for user space.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use cfg80211 add/del_beacon callbacks for starting/stopping AP mode and
set_beacon to update AP configuration (mainly, to update Beacon and
Probe Response IEs).
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It would be at <dbgfs_root>/ieee80211/phyX/ath6kl/credit_dist_stats.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It would be at <debugfs_root>/ieee80211/phyX/ath6kl/tgt_stats.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Just initial debugfs changes. The debugfs directory would
be created at <debugfs_root>/ieee80211/phyX/ath6kl.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Current tx scatter gather implementation rolls back the entire
scatter setup in case of a failure in setting up just one packet
into the bundle. Instead of dopping the whole scatter setup,
send the packets available just before the failure one using
scatter gather I/O.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Patch "ath6kl: Fix buffer alignment for scatter-gather write" does
memmove for a length (scat_req->scat_list[i].len) which is not the
actual length of data that is suppossed to be moved. The right
lengh is packet->act_len + HTC_HDR_LENGTH. Using wrong length
for data move during buffer alignment causes system freeze after
the following WARN_ON and sometimes target assert.

WARNING: at drivers/net/wireless/ath/ath6kl/main.c:771 ath6k_credit_distribute+0x196/0x1a0
 [<ffffffffa051cf5f>] ath6kl_htc_rxmsg_pending_handler+0x83f/0xe00 [ath6kl]
 [<ffffffff8104a743>] ? __wake_up+0x53/0x70
 [<ffffffffa0518b18>] ath6kldev_intr_bh_handler+0x188/0x650 [ath6kl]
 [<ffffffffa052d316>] ath6kl_sdio_irq_handler+0x36/0x80 [ath6kl]
 [<ffffffff81492b3c>] sdio_irq_thread+0xfc/0x360
 [<ffffffff81051c52>] ? default_wake_function+0x12/0x20
 [<ffffffff81492a40>] ? sdio_claim_irq+0x220/0x220
 [<ffffffff81080c36>] kthread+0x96/0xa0
 [<ffffffff815b9fb4>] kernel_thread_helper+0x4/0x10
 [<ffffffff81080ba0>] ? kthread_worker_fn+0x190/0x190
 [<ffffffff815b9fb0>] ? gs_change+0x13/0x13
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For now this is implemented so that if host supports power is kept in
the chip. If that's not supported, an error is returned and sdio stack
will remove the device during suspend.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For non-scatter buffers, there is already a bounce buffer which
takes care of alignment. This patch is influenced by a rough patch of
Kalle.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This fixes AMSDU rx, otherwise it fails with the following warnings.

"802.3 AMSDU frame bound check failed"
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This lock is intended to protect stats there, not neccessary to
hold it beyond that.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

One line used space to indent. Oddly enough checkpatch didn't complain
about this.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

 In some random cases, the firmware is sending two disconnect event to
 the host. In the current model, both diconnect events are passed to
 cfg80211 without checking local sme state machine, which is screwing
 cfg80211 layer state.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Connect event handler function is always reporting BSS info
to CFG80211 layer first and then followed by connect event is passed.

Before these steps, BSS presence is retrieved from CFG80211 layer,
but it is not used. Hence, removing that part.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Support isn't complete yet.
Signed-off-by: NKevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There is no point in generating a bogus Beacon frame for
cfg80211_inform_bss_frame when cfg80211_inform_bss can be used
instead.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

this comment refers to some code that was removed.
Signed-off-by: NGreg Dietsche <Gregory.Dietsche@cuw.edu>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With sequence number and buffer allocation deferred to when they're needed
for the first time, it becomes much easier to start dropping packets from
the tid queue if necessary, e.g. when latency suddenly increases. This can
lead to some future improvements in buffer management for better latency.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is only necessary for BAW tracking and moving it to the ath_buf
makes it easier to add further improvements, such as deferring
seqno allocation in the aggregation path.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>