The ENABLE_APE flag tells the driver whether or not the device has an
Application Processing Engine (APE).  The APE does not need the PHY to
be powered unless it is running management firmware.  For backwards
compatibility, management firmware will still set the ENABLE_ASF bit.
Consequently, there is no reason to consider the ENABLE_APE flag when
deciding whether or not to power down the phy.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Per Dave Miller's suggestion, replace the remaining ioremap_nocache()
call with pci_ioremap_bar().  Remove the two IORESOURCE_MEM checks as
they are redundant.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch extracts the bootcode firmware version from the alternate
selfboot patch NVRAM format.  This format is used on the 5784, 5761 and
some newer devices.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GPHY Autopowerdown (APD) is a way to save power when energy is not
detected on the wire.  At the moment, only the 5784 and 5761 are
capable of enabling this mode.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch disables CLKREQ at 10Mbps and 100Mbps to workaround a TX BD
corruption issue.  This problem only affects the 5784 and 5761 (and
57780 AX) ASIC revisions.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes sure the device is a PCIX device before attempting to
use the pcix_cap device structure member.  This is prep work for the
following patch.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch replaces hardcoded 2's with the NET_IP_ALIGN constant or
TG3_RAW_IP_ALIGN where appropriate.  Some platforms can redefine the
NET_IP_ALIGN definition to zero if unaligned DMA transfers cost more
than the IP header alignment gains.  This patch represents a
performance improvement when using the 5701 on these platforms.
The copy path can be avoided.

TG3_RAW_IP_ALIGN is used in cases where we always want to align the
IP header on dword boundaries.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove redundant argument comments in files of net/*
Signed-off-by: NQinghuang Feng <qhfeng.kernel@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check return code for all NVM accesses[1] and error out accordingly; log
a debug message for failed accesses.

For ICH8/9, the valid NVM bank detect function was not checking whether the
SEC1VAL (sector 1 valid) bit in the EECD register was itself valid (bits 8
and 9 also have to be set).  If invalid, it would have defaulted to the
possibly invalid bank 0.  Instead, try to use the valid bank detection
method used by ICH10 which has been cleaned up a bit.

[1] - reads and updates only; not writes because those are only writing to
the Shadow RAM, the update following the write is the only thing actually
writing the modified Shadow RAM contents to the NVM.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On 82571 with SerDes, the true link state is not always correct when read
from the STATUS register; use existing e1000_has_link() function instead.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than reading the NVM to get the EEPROM version number everytime the
ethool get_drvinfo function is called, read it once during probe and save
it for future reference.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add missing newline from debug message.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sync flow control variables and usage model with that found in the ixgbe
driver.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The system log messages created on a link status change need to follow a
specific format to work with tools some customers use.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On ESB2, the MAC-to-PHY (Kumeran) interface must be configured after link
is up before any traffic is sent; a new PHY operations function pointer is
provided for this.  To facilitate read/write of the Kumeran registers
without blocking PHY register writes, the driver/firmware synchronization
method which previously used a hardware semaphore for both PHY and Kumeran
register accesses is now split.  New Kumeran register read/write functions
utilize this new synchronization method.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check return of pci_save_state and error out accordingly.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some branding strings (displayed via lspci) are missing from the comments in
various family-specific files in the driver.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for link test does not work properly for 82571 parts in a blade
environment with an unterminated serdes link partner.  Make the test more
robust by checking the invalid bit.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Follow the convention used elsewhere in e1000e to 'commit' PHY changes
instead of directly writing to the PHY CTRL register to reset it.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There has been an issue seen with the pci-e quad port adapters that will
cause them to generate a pci-e correctable error on some system while
transitioning to D3.

Since no action is needed on this correctable error the simplest solution
is to mask off the reporting of correctable errors.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

They are no longer a rwlocks.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When compile test my previous patch, I found PC300 driver was broken.
And there is no explanation about the broken.
Add the reason about why change this driver to broken in Kconfig.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

netdev's private data should be hdlc.
pc300dev_t is the private data of hdlc.
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For killing directly reference of netdev->priv, use netdev->ml_priv to replace it.
Because the private pvc data comes from add_pvc() and can't be allocated in
alloc_netdev().
Signed-off-by: NWang Chen <wangchen@cn.fujitsu.com>
Acked-by: NKrzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can avoid some useless instructions if !CONFIG_NET_NS

Because of RCU, we use INET_MATCH or INET_TW_MATCH twice for the found
socket, so thats six instructions less per incoming TCP packet.

Yet another tbench speedup :)
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds #include <linux/timer.h> in lib80211.h to avoid
these compilation erros.

> In file included from /work/src/wireless-testing/net/wireless/lib80211.c:24:
> /work/src/wireless-testing/include/net/lib80211.h:113: error: field
> 'crypt_deinit_timer' has incomplete type
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_info_init':
> /work/src/wireless-testing/net/wireless/lib80211.c:83: error: implicit
> declaration of function 'setup_timer'
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_info_free':
> /work/src/wireless-testing/net/wireless/lib80211.c:95: error: implicit
> declaration of function 'del_timer_sync'
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_deinit_handler':
> /work/src/wireless-testing/net/wireless/lib80211.c:157: error:
> implicit declaration of function 'add_timer'
> /work/src/wireless-testing/net/wireless/lib80211.c: In function
> 'lib80211_crypt_delayed_deinit':
> /work/src/wireless-testing/net/wireless/lib80211.c:182: error:
> implicit declaration of function 'timer_pending'
> make[3]: *** [net/wireless/lib80211.o] Error 1
> make[2]: *** [net/wireless] Error 2
> make[1]: *** [net] Error 2
> make: *** [sub-make] Error 2
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Modify the file comments to reflect the current maintainers.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As noted by John Linville, the RTL818X maintainers have "moved on", and the
responsibilities for RTL8180 and RTL8187 have been split. This is the
corresponding update of MAINTAINERS.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove converting the MAC address to a string by a direct byte
conversion and use %pM instead, since the code is now boilerplate
use a macro to define the show functions, and also use the shorter
__ATTR_RO macro to define the attributes.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Michael and Andrea have moved-on, so we shouldn't be bothering them
about these drivers anymore.

Actually, Herton Ronaldo Krzesinski, Hin-Tak Leung, and Larry Finger
have been handling the rtl8187 stuff for a while.  So, I would welcome a
patch from one of them changing this to just RTL8180 and adding an
RTL8187 entry with their names...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This updates rtl8180 handling for short slot after "mac80211: fix short
slot handling". Only rtl8180_rtl8225 actually had code for handling
short slot times, so the other RF devices are untouched by this change.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Otherwise, the BUILD_BUG_ON calls in ieee80211_tx_info_clear_status can
fail on some architectures.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The old ieee80211 code only remains as a support library for the ipw2100
and ipw2200 drivers.  So, move the code and rename it appropriately to
reflects it's true purpose and status.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These bits are shared already between ipw2x00 and hostap, and could
probably be shared both more cleanly and with other drivers.  This
commit simply relocates the code to lib80211 and adjusts the drivers
appropriately.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

orinoco_translate_scan() and orinoco_translate_ext_scan() wrongly
truncate last_scanned argument from unsigned long to unsigned int.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes unnecessary #include <linux/netdevice.h> from
/net/mac80211/mlme.c.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Indirect registers require multiple calls to the CSR
register in order to access the indirect registers.
This must be protected under a lock to prevent race
conditions which could cause invalid data to
be returned when reading from the indirect register or silent
failures when writing data to the indirect register.

USB drivers where already protected under a mutex,
so rename the mutex and make PCI drivers use the mutex
as well.
This now means that BBP and RF registers are no longer
accessible in interrupt context. That is not a bad
situation since the slow behavior of accessing
those registers means we don't _want_ to access them
in interrupt context either.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>