After we've told the irq code we don't want to handle display irqs
anymore, we must make sure any display irq handling already
kicked off has finished before we actually turn off the power well.

I wouldn't expect PIPESTAT based interrupts to occur anymore since
vblanks/page flips/gmbus/etc should all be quiescent at this point.
But at least hotplug interrupts could still occur. Hotplug
interrupts may also kick off the workqueue based hotplug processing,
but that code should take the required power domain references
itself, so there shouldn't be any need to synchronize with the
hotplug processing from the power well code.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455900112-15387-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

PIPESTAT registers live in the display power well on VLV/CHV, so we
shouldn't access them when things are powered down. Let's check
whether the display interrupts are on or off before accessing the
PIPESTAT registers.

Another option would be to read the PIPESTAT registers only when
the IIR register indicates that there's a pending pipe event. But
that would mean we might miss even more underrun reports than we
do now, because the underrun status bit lives in PIPESTAT but doesn't
actually generate an interrupt.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93738
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455825266-24686-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

DMC debugmask bits should stick so no need to write them
everytime dc state is changed.

v2: Write after firmware has been successfully loaded (Ville)
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455808874-22089-5-git-send-email-mika.kuoppala@intel.com

Cores need to be included into the debug mask. We don't exactly
know what it does but the spec says it must be enabled. So obey.

v2: Cores should be only set for BXT (Imre, Art)

Cc: Imre Deak <imre.deak@intel.com>
Cc: Runyan, Arthur J <arthur.j.runyan@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455877564-5128-1-git-send-email-mika.kuoppala@intel.com

It has been observed that sometimes disabling the dc6 fails
and dc6 state pops back up, brief moment after disabling. This
has to be dmc save/restore timing issue or other bug in the
way dc states are handled.

Try to work around this issue as we don't have firmware fix
yet available. Verify that the value we wrote for the dmc sticks,
and also enforce it by rewriting it, if it didn't.

v2: Zero rereads on rewrite for extra paranoia (Imre)

Testcase: kms_flip/basic-flip-vs-dpms
References: https://bugs.freedesktop.org/show_bug.cgi?id=93768
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455811089-27884-1-git-send-email-mika.kuoppala@intel.com

The DMC can incorrectly run off and allow DC states on it's own. We
don't know the root-cause for this yet but this patch makes it more
visible.
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455808874-22089-2-git-send-email-mika.kuoppala@intel.com

These platforms should be fine now.

FBC can allow very significant power savings for screen-on idle
systems, but it is worth mentioning that a lot of people won't get
significant power savings by enabling this feature because they may
have something else preventing the system from getting into the
deepest sleep states. Examples may include a hungry wifi device or a
max_performance SATA link power management policy. You can check your
PC state residencies on the powertop "Idle stats" tab. I recommend
trying to run "sudo powertop --auto-tune" and then seeing if the
residencies improve.

Oh, and in case you - the person reading this commit message - found
this commit through git bisect, please do the following:
 - Check your dmesg and see if there are error messages mentioning
   underruns around the time your problem started happening.
 - Download intel-gpu-tools, compile it, and run:
   $ sudo ./tests/kms_frontbuffer_tracking --run-subtest '*fbc-*' 2>&1 | tee fbc.txt
   Then send us the fbc.txt file, especially if you get a failure.
   This will really maximize your chances of getting the bug fixed
   quickly.
 - Try to find a reliable way to reproduce the problem, and tell us.
 - Boot with drm.debug=0xe, reproduce the problem, then send us the
   dmesg file.

v2: Don't enable by default on SKL.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455655643-2535-1-git-send-email-paulo.r.zanoni@intel.com

This is a manual revert of

commit 7a10dfa6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Apr 1 09:33:47 2014 +0200

    drm/i915: Add debug module option for VTd validation

as no users have appeared.
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455621493-6865-2-git-send-email-jani.nikula@intel.com

We've given write permissions to dynamically change some module
parameters through /sys/module/i915/parameters although they only
support setting on module load. Fix the permissions.
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455621493-6865-1-git-send-email-jani.nikula@intel.com

The bpp value which is used while calulating the txbyteclkhs values
should be wrt the pixel format value. Currently bpp is coming
from pipe config to calculate txbyteclkhs. Fix it in this patch.

V2: dsi_pixel_format_bpp is used to retrieve the bpp from pixel_format
	[Review: Jani]
Signed-off-by: NDeepak M <m.deepak@intel.com>
Signed-off-by: NYogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Tested-by: Mika Kahola <mika.kahola@intel.com> # BYT
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455203007-10850-1-git-send-email-ramalingam.c@intel.com

DSP CLK_GATE registers are specific to BYT and CHT.
Avoid programming the same for BXT platform.

v2: Rebased on latest drm nightly branch.

v3: Fixed Jani's review comments
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455796166-13052-1-git-send-email-jani.nikula@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Spotted-by: NMika Kuoppala <mika.kuoppala@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93441
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455719489-3008-1-git-send-email-imre.deak@intel.com

We have an open coded loop which tries to see if the encoder has any
connectors linked to it. Let's extract that to a helper similar to
intel_crtc_has_encoders().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455737325-14777-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is another step in removing legacy state.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455697119-31416-6-git-send-email-maarten.lankhorst@linux.intel.com

With the conversion to atomic only on/off are still supported.
The rest is mapped to one of those, and when enable is called
DPMS_ON should be true.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455697119-31416-5-git-send-email-maarten.lankhorst@linux.intel.com

Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455697119-31416-4-git-send-email-maarten.lankhorst@linux.intel.com

Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455697119-31416-3-git-send-email-maarten.lankhorst@linux.intel.com

Instead of restoring dpms and a flag for whether a temp fb is allocated duplicate
an atomic state before the new state is committed, and commit it the old state
in intel_release_load_detect_pipe.

Changes since v1:
- Use a real atomic state. (Ville)
Changes since v2:
- Do not preserve shared_dpll any more, no need to do so. (Ville)
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455697119-31416-2-git-send-email-maarten.lankhorst@linux.intel.com

With a reliable frontbuffer tracking and all instability corner cases
on Haswell and Broadwell solved let's re-enabled PSR by default on
these platforms.

In case a new issue is found and PSR is the main suspect, please check
if i915.enable_psr=0 really makes your problem go away. If this is the case
PSR is the culprit so after that please check if i915.enable_psr=2
or i915.enable_psr=3 solves your issue and please let us know.
There are many panels out there and not all implementations apparently
work as we would expect.

In case you needed to force it on standby or disabled or in case of any
PSR related bug please report it at bugs.freedesktop.org.
In a bugzilla entry for PSR is desirable:
- dmesg (drm.debug=0xe)
- output of /sys/kernel/debug/dri/0/i915_edp_psr_status
- Platform information. Vendor, model, id, pci id.
- Graphical environment: Gnome, KDE, openbox, etc...
- Details how to reproduce.
- Also good if you could run PSR test cases of Intel-gpu-tools
- Please mention if forcing main link standby or main link off helps you.

There are Intel-gpu-tools test cases that can be helpful to
determine if PSR is working as expected:
kms_psr_sink_crc and kms_psr_frontbuffer_tracking.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455278893-1307-2-git-send-email-rodrigo.vivi@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With a reliable frontbuffer tracking and all instability corner cases
solved for this platform let's re-enabled PSR by default.

In case a new issue is found and PSR is the main suspect, please check
if i915.enable_psr=0 really makes your problem go away,
please report it at bugs.freedesktop.org.

In a bugzilla entry for PSR is desirable:
- dmesg (drm.debug=0xe)
- output of /sys/kernel/debug/dri/0/i915_edp_psr_status
- Platform information. Vendor, model, id, pci id.
- Graphical environment: Gnome, KDE, openbox, etc...
- Details how to reproduce.
- Also good if you could run PSR test cases of Intel-gpu-tools
- Please mention if forcing main link standby or main link off helps you.

There are Intel-gpu-tools test cases that can be helpful to
determine if PSR is working as expected:
 kms_psr_sink_crc and kms_psr_frontbuffer_tracking.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This will give us flexibility to enable PSR by default independently so
issues and corner cases in one platform won't affect others were we have
it working properly.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise a pde_shift big enough to overflow a u32 will be truncated before
assignment

Note: We never asked for ranges spanning a 4G boundary, so this issue
doesn't cause a real problem.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
[danvet: Add note why this isn't a real problem.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20160217142043.4947.60447.stgit@localhost.localdomain

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-13-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-12-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-11-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-10-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.

While at it also add the missing reference around the HW access in
i915_interrupt_info().

v2:
- update the commit message mentioning that this also fixes the
  HW access in the interrupt info debugfs entry (Daniel)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-9-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-8-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93439
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-7-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-6-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-5-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-4-git-send-email-imre.deak@intel.com

The assumption when adding the intel_display_power_is_enabled() checks
was that if it returns success the power can't be turned off afterwards
during the HW access, which is guaranteed by modeset locks. This isn't
always true, so make sure we hold a dedicated reference for the time of
the access.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Revieved-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455296121-4742-3-git-send-email-imre.deak@intel.com

We have many places in the code where we check if a given display power
domain is enabled and if so access registers backed by this power
domain. We assumed that some modeset lock will prevent the power
reference from vanishing in the middle of the HW access, but this
assumption doesn't always hold. In such cases we get either the wakeref
not held, or an unclaimed register access error message. To fix this in
a future-proof way that's independent of other locks wrap any such
access with a get_ref_if_enabled()/put_ref() pair.

Kudos to Ville and Joonas for the ideas of this new interface.

v2:
- init the power_domains ptr when declaring it everywhere (Joonas)
v3:
- don't report the device to be powered if runtime PM is disabled

CC: Mika Kuoppala <mika.kuoppala@intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455711462-7442-1-git-send-email-imre.deak@intel.com

userptr requires mmu-notifier for full unprivileged support. Most
systems have mmu-notifier support already enabled as a requirement for
virtualisation support, but we should make the option for i915 to take
advantage of mmu-notifiers explicit (and enable by default so that
regular userspace can take advantage of passing client memory to the
GPU.)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1452503961-14837-3-git-send-email-chris@chris-wilson.co.uk

Unfortunately i915 is still not fully atomic, and expects mode_config.mutex
to be held during modeset until we finally fix it.

This fixes the following WARN when resuming:

[  425.208983] ------------[ cut here ]------------
[  425.208990] WARNING: CPU: 0 PID: 6828 at drivers/gpu/drm/drm_edid.c:3555 drm_select_eld+0xa5/0xd0()
[  425.209015] Modules linked in: pl2303 usbserial snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic intel_powerclamp coretemp i915 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_intel snd_hda_codec snd_hwdep lpc_ich snd_hda_core snd_pcm i2c_hid i2c_designware_platform i2c_designware_core r8169 mii sdhci_acpi sdhci mmc_core
[  425.209018] CPU: 0 PID: 6828 Comm: kworker/u4:5 Tainted: G     U  W       4.5.0-rc4-gfxbench+ #1
[  425.209020] Hardware name: \xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff \xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff\xffffffff/DN2820FYK, BIOS FYBYT10H.86A.0038.2014.0717.1455 07/17/2014
[  425.209027] Workqueue: events_unbound async_run_entry_fn
[  425.209032]  0000000000000000 ffff880072433958 ffffffff813f6b05 0000000000000000
[  425.209036]  ffffffff81aaef2d ffff880072433990 ffffffff81078291 ffff880036b933d8
[  425.209039]  ffff88006d528000 ffff88006d52b3d8 ffff88006d52b3d8 ffff88007315b6f8
[  425.209040] Call Trace:
[  425.209045]  [<ffffffff813f6b05>] dump_stack+0x67/0x92
[  425.209049]  [<ffffffff81078291>] warn_slowpath_common+0x81/0xc0
[  425.209052]  [<ffffffff81078385>] warn_slowpath_null+0x15/0x20
[  425.209054]  [<ffffffff8151e195>] drm_select_eld+0xa5/0xd0
[  425.209101]  [<ffffffffa01f34f4>] intel_audio_codec_enable+0x44/0x160 [i915]
[  425.209135]  [<ffffffffa023eac7>] intel_enable_hdmi_audio+0x87/0x90 [i915]
[  425.209169]  [<ffffffffa023eb5a>] g4x_enable_hdmi+0x8a/0xa0 [i915]
[  425.209202]  [<ffffffffa023f41b>] vlv_hdmi_pre_enable+0x1cb/0x240 [i915]
[  425.209236]  [<ffffffffa020edcf>] valleyview_crtc_enable+0x10f/0x290 [i915]
[  425.209270]  [<ffffffffa020ba49>] intel_atomic_commit+0x769/0x17a0 [i915]
[  425.209274]  [<ffffffff81526ad5>] ? drm_atomic_check_only+0x145/0x660
[  425.209276]  [<ffffffff81527022>] drm_atomic_commit+0x32/0x50
[  425.209310]  [<ffffffffa0215fa0>] intel_display_resume+0xa0/0x130 [i915]
[  425.209338]  [<ffffffffa018c1bb>] i915_drm_resume+0xcb/0x160 [i915]
[  425.209366]  [<ffffffffa018c272>] i915_pm_resume+0x22/0x30 [i915]
[  425.209370]  [<ffffffff8143d91e>] pci_pm_resume+0x6e/0xe0
[  425.209373]  [<ffffffff8143d8b0>] ? pci_pm_resume_noirq+0xa0/0xa0
[  425.209375]  [<ffffffff815409ae>] dpm_run_callback+0x6e/0x280
[  425.209378]  [<ffffffff815410b2>] device_resume+0x92/0x250
[  425.209380]  [<ffffffff81541288>] async_resume+0x18/0x40
[  425.209382]  [<ffffffff8109c7a5>] async_run_entry_fn+0x45/0x140
[  425.209386]  [<ffffffff81093293>] process_one_work+0x1e3/0x620
[  425.209388]  [<ffffffff810931f7>] ? process_one_work+0x147/0x620
[  425.209391]  [<ffffffff81093719>] worker_thread+0x49/0x490
[  425.209393]  [<ffffffff810936d0>] ? process_one_work+0x620/0x620
[  425.209396]  [<ffffffff81099e0a>] kthread+0xea/0x100
[  425.209400]  [<ffffffff81099d20>] ? kthread_create_on_node+0x1f0/0x1f0
[  425.209404]  [<ffffffff817ba03f>] ret_from_fork+0x3f/0x70
[  425.209407]  [<ffffffff81099d20>] ? kthread_create_on_node+0x1f0/0x1f0
[  425.209409] ---[ end trace d1b247107f34a8b2 ]---

Fixes: e2c8b870 ("drm/i915: Use atomic helpers for suspend, v2.")
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455632862-18557-1-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The check for active_crtcs == 0 was performed by the callers, when changing
the patches I forgot to remove those hunks.

This resulted in skylake scalers still not having the correct cdclk to
calculate scaling when all crtc's were dpms off.

Fixes: 1a617b77 ("drm/i915: Keep track of the cdclk as if all crtc's were active.")
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455614711-9045-1-git-send-email-maarten.lankhorst@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Instead of duplicating the functionality now that we no longer need
to preserve dpll state we can move to using the upstream suspend helper.

Changes since v1:
- Call hw readout with all mutexes held.
- Rework intel_display_suspend to only assign modeset_restore_state
  on success.
Signed-off-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/56C2E686.5060803@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

This behavior of checking for a shmem backed GEM object was introduced here:
commit 4c914c0c
Author: Brad Volkin <bradley.d.volkin@intel.com>
Date:   Tue Feb 18 10:15:45 2014 -0800

    drm/i915: Refactor shmem pread setup

It is possible for an object to not be a shmem backed GEM object (for example
userptr objects). An example of how we hit this failure can be found through
copy_batch() in the command parser because we allocate a userptr object for the
batch which contains privileged instructions. Userptr calls
drm_gem_private_object_init() which explicitly sets the filp to none.

NOTE: I manually retyped this from a test machine. So I haven't even compiled
this exact patch.

v2: Use same logic as from a2a4f916c2f (Kristian, Dave Gordon)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Cc: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: NBen Widawsky <benjamin.widawsky@intel.com>
Tested-by: Jordan Justen <jordan.l.justen@intel.com> (v1)
Reviewed-by: Jordan Justen <jordan.l.justen@intel.com> (v1)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1455047053-2644-1-git-send-email-benjamin.widawsky@intel.com

Unknown parameters, especially structure padding, are expected to invoke
rejection with -EINVAL.

v2: similar issue exists for context-create

Testcase: igt/gem_ctx_create/invalid-pad
Testcase: igt/gem_ctx_bad_destroy/invalid-pad
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89602
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93999Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1454690759-31201-1-git-send-email-chris@chris-wilson.co.uk