Properly clear the memory, and set "pr->flags.power" only if a C2 or
deeper state is valid (to make the code match both the comment and
previous behaviour).

This fixes a boot-time lockup reported by Maneesh Soni when using
"maxcpus=1".
Acked-by: NManeesh Soni <maneesh@in.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The code Ben H added needs <linux/pci.h> for things like pci_dev, etc.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

It was causing too many problems, and this is not the proper type of
driver for this device.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This lets us remove a lot of code in the drivers that were all checking
the same thing.  It also found some bugs in a few of the drivers, which
has been fixed up.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix an error in the OHCI lh7a404 driver after the platform device
conversion.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This small patch adds a device ID used by older Maxtor OneTouch drives
(the ones with blue face-plate instead of the fancy silver one used in
newer models). The button on those drives works well with the current
driver.

From: Antti Andreimann <Antti.Andreimann@mail.ee>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

drivers/usb/core/devio.c: In function `proc_ioctl_compat':
drivers/usb/core/devio.c:1401: warning: passing arg 1 of `compat_ptr' makes integer from pointer without a cast
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

this patch from Herbert Xu fixes a race by moving termination of
the URBs into close() exclusively.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Peter Favrholdt reported that his Kodak flash device was getting
detected as a CDROM, and he helped me track this down to the fact that
the device takes a long time (approx 440ms!) to reset.

This patch increases the delay to 500ms, which solves the problem.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

the scsi layer now uses very short sg lists. This breaks the microtek
driver. Here is a patch fixes this and some other issues.
Signed-off-by: NOliver Neukum <oliver@neukum.name>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Updates pl2303_update_line_status() to handle X75 and SX1 Siemens mobiles
Signed-off-by: NLuiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds two new Siemens mobiles IDs for the pl2303 driver.
Signed-off-by: NLuiz Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

The onetouch support doesn't suspend correctly (leaves an interrupt
URB posted, instead of unlinking it) so for now just disable it
when PM is in the air.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Jablotron usb serial interface identification
Signed-off-by: NJosef Balatka <balatka@email.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

I actually have this device, and kernel reports blacklist entry is no
longer neccessary.
Signed-off-by: NPavel Machek <pavel@suse.cz>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

drivers/usb/core/devio.c: In function `proc_ioctl_compat':
drivers/usb/core/devio.c:1401: warning: passing arg 1 of `compat_ptr' makes integer from pointer without a cast

NFI if this is correct...

Cc: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

USB: fix 'unused variable' warning
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds support for Graphire4, Cintiq 710, Intuos3 6x11, etc. and
report Device IDs.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This patch adds support for Graphire4, Cintiq 710, Intuos3 6x11, etc.
Signed-off-by: NPing Cheng <pingc@wacom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

People are complaining about a .old file in the tree.  So rename
drivers/usb/serial/ChangeLog.old to ChangeLog.history.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Platform device conversion missed a couple of spots.
Signed-off-by: NDeepak Saxena <dsaxena@plexity.net>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This fixes a slab corruption issue in the ipw2200 driver: it essentially
multiplied the error log number _twice_ by the size of the error element
entry (once explicitly in the code, and once implicitly as part of the
regular pointer arithmetic).

Cc: Henrik Brix Andersen <brix@gentoo.org>
Cc: Bernard Blackham <bernard@blackham.com.au>
Cc: Zilvinas Valinskas <zilvinas@gemtek.lt>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
--

The function ipw_request_direct_scan() should bail out when the device
is down.  This fixes a lockup caused by wpa_supplicant triggering
ipw_request_direct_scan() while the driver was in a middle of a reset
due to firmware errors.

Thanks to Zilvinas Valinskas for reporting the bug and helping me
debug it.
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This driver supports the IDE port on the Sibyte Swarm evaluation boards
and it's relatives for the BCM1250 family of systems on a chip.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Not that it's meant to be sustained for long, but from time to time it's
useful to have some console...
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Handle errata (it was unintentional on this h/w, whereas its intentional
on others) whereby the nIEN bit in Device Control is ignored, leading to
a situation where a hardware interrupt completes the qc before the
polling code has a chance to.

This will get fixed The Right Way(tm) once Albert Lee's irq-pio
branch is merged, as the more natural PIO method on this hardware is
interrupt-driven.

- DMA boundary was being handled incorrectly.  Copied the code from
  ata_fill_sg(), since Marvell has the same DMA boundary needs.
  (we can't use ata_fill_sg directly since we have different hardware
   descriptors)
- cleaned up the SATA phy reset code, to deal with various errata

This fixes a problem with offb not parsing addresses properly on 64 bits
machines, and thus crashing at boot.  The problem is worked around by
locating the matching PCI device and using the properly relocated PCI
base addresses instead of misparsing the Open Firmware properties.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

ATA devices don't generate many errors, so the preferred method is to
printk() when they occur.

ATAPI devices generate tons of exceptions during the normal course
of operation, so this change skips logging the most common class of
errors.

  The following code segment is not functional because the transfer cycle time speficied by
  the EIDE device is later overwritten by ata_timing_quantize():

	/*
	 * If the drive is an EIDE drive, it can tell us it needs extended
	 * PIO/MW_DMA cycle timing.
	 */
	if (adev->id[ATA_ID_FIELD_VALID] & 2) {	/* EIDE drive */
		memset(&p, 0, sizeof(p));
		(snip)
		ata_timing_merge(&p, t, t, ATA_TIMING_CYCLE | ATA_TIMING_CYC8B);
               <== uninitialized "t" is used here
	}

	/*
	 * Convert the timing to bus clock counts.
	 */
	ata_timing_quantize(s, t, T, UT);  <== t is overwritten by quantized s

  The patch has been submitted for ide-timing.h before:
  http://marc.theaimsgroup.com/?l=linux-ide&m=110820013425454&w=2
  Resubmitted for libata.

Changes:
  - Minor fix to honor the following transfer cycle time speficied by the device
    - id[65]: Minimum Multiword DMA transfer cycle time per word
    - id[67]: Minimum PIO transfer cycle time without flow control
    - id[68]: Minimum PIO transfer cycle time with IORDY
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>

=======
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Adds constants for ATAPI support to sata_sil24.  This patch is
originally from Jeff Garzik <jgarzik@pobox.com>.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jgarzik@pobox.com>

Currently, the version when ENABLE_RC is defined, falls through
to the end of the function without returning anything.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

From: Guido Guenther <agx@sigxcpu.org>

- Use correct API for allocating and freeing DMA buffers.
Acked-by: NJohannes Stezenbach <js@linuxtv.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

- Fix a regression in command completion, which prevented
  the restart of the DMA engine after the device throws
  an error.
- Pack more hardware info into the port-reset error message.
- Promote "welcome to our timeout" message from debug msg
  to normal printk.

drivers/block/cciss_scsi.c:264: warning: `print_bytes' defined but not used
drivers/block/cciss_scsi.c:298: warning: `print_cmd' defined but not used
Signed-off-by: NGrant Coady <gcoady@gmail.com>
Acked-by: NMike Miller <mike.miller@hp.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>