[ Upstream commit e5017716adb8aa5c01c52386c1b7470101ffe9c5 ]

The "index + count" addition can overflow.  Both come directly from the
user.  This bug leads to an information leak.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Peter Malone <peter.malone@gmail.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Mathieu Malaterre <malat@debian.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d8bad911e5e55e228d59c0606ff7e6b8131ca7bf ]

I'm not sure why the code assumes that only the first put_user() needs
an access_ok() check.  I have made all the put_user() and get_user()
calls checked.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Cc: Mathieu Malaterre <malat@debian.org>
Cc: Peter Malone <peter.malone@gmail.com>,
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 60e5e48dba72c6b59a7a9c7686ba320766913368 ]

When a device tree set a display-timing using native-mode
then according to the bindings doc this should:

    native-mode:
    The native mode for the display, in case multiple
    modes are provided.
    When omitted, assume the first node is the native.

The atmel_lcdfb used the last timing subnode and did not
respect the timing mode specified with native-mode.

Introduce use of of_get_videomode() which allowed
a nice simplification of the code while also
added support for native-mode.

As a nice side-effect this fixes a memory leak where the
data used for timings and the display_np was not freed.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 54541815b43f4e49c82628bf28bbb31d86d2f58a ]

Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size. The
size used is the result of a discussion with Renesas hardware engineers
and unfortunately not found in the datasheet.

  renesas_sdhi_internal_dmac ee140000.sd: DMA-API: mapping sg segment
  longer than device claims to support [len=126976] [max=65536]
Reported-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
[wsa: simplified some logic after validating intended dma_parms life cycle
      and added comment]
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b85fb0a1c8aeaaa40d08945d51a6656b512173f0 ]

SDR104, HS200 and HS400 need to check for SCC error. If SCC error is
detected, retuning is necessary.
Signed-off-by: NMasaharu Hayakawa <masaharu.hayakawa.ry@renesas.com>
[Niklas: update commit message]
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2e1501a8bdd49eaa0e967c0ad00e9dcd68d0b30f ]

We need r8a774a1 to be whitelisted for SDHI to work on the RZ/G2M,
but we don't care about the revision of the SoC, so just whitelist
the generic part number.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NBiju Das <biju.das@bp.renesas.com>
Reviewed-by: NSimon Horman <horms+renesas@verge.net.au>
Reviewed-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 07e1d88adaaeab247b300926f78cc3f950dbeda3 ]

On 64-bit kernels ptrace can read the FS/GS base using the register access
APIs (PTRACE_PEEKUSER, etc.) or PTRACE_ARCH_PRCTL.

Make both of these mechanisms return the actual FS/GS base.

This will improve debuggability by providing the correct information
to ptracer such as GDB.

[ chang: Rebased and revised patch description. ]
[ mingo: Revised the changelog some more. ]
Signed-off-by: NAndy Lutomirski <luto@kernel.org>
Signed-off-by: NChang S. Bae <chang.seok.bae@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Markus T Metzger <markus.t.metzger@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Shankar <ravi.v.shankar@intel.com>
Cc: Rik van Riel <riel@surriel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1537312139-5580-2-git-send-email-chang.seok.bae@intel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 541d7fdd7694560404c502f64298a90ffe017e6b ]

The AF_XDP socket struct can exist in three different, implicit
states: setup, bound and released. Setup is prior the socket has been
bound to a device. Bound is when the socket is active for receive and
send. Released is when the process/userspace side of the socket is
released, but the sock object is still lingering, e.g. when there is a
reference to the socket in an XSKMAP after process termination.

The Rx fast-path code uses the "dev" member of struct xdp_sock to
check whether a socket is bound or relased, and the Tx code uses the
struct xdp_umem "xsk_list" member in conjunction with "dev" to
determine the state of a socket.

However, the transition from bound to released did not tear the socket
down in correct order.

On the Rx side "dev" was cleared after synchronize_net() making the
synchronization useless. On the Tx side, the internal queues were
destroyed prior removing them from the "xsk_list".

This commit corrects the cleanup order, and by doing so
xdp_del_sk_umem() can be simplified and one synchronize_net() can be
removed.

Fixes: 965a9909 ("xsk: add support for bind for Rx")
Fixes: ac98d8aa ("xsk: wire upp Tx zero-copy functions")
Reported-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NBjörn Töpel <bjorn.topel@intel.com>
Acked-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8c7fd6a365eb5b2647b2c01918730d0a485b9f85 ]

In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed.  Note that RSC is sent separately in
a new command.  This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 757c968c442397f1249bb775a7c8c03842e3e0c7 ]

There was a small race when removing the sbshc module where
smbus_alarm() had queued acpi_smbus_callback() for deferred execution
but it hadn't been run yet, so that when it did run hc had been freed
and the module unloaded, resulting in an invalid paging request.

A similar race existed when removing the sbs module with regards to
acpi_sbs_callback() (which is called from acpi_smbus_callback()).

We therefore need to ensure no callbacks are pending or executing before
the cleanups are done and the modules are removed.
Signed-off-by: NRonald Tschalär <ronald@innovation.ch>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f1193e915748291fb205a908db33bd3debece6e2 ]

This place should want to initialize array, not a element,
so it should be sizeof(array) instead of sizeof(element)

but now this array only has one element, so no error in
this condition that XFRM_MAX_OFFLOAD_DEPTH is 1
Signed-off-by: NLi RongQing <lirongqing@baidu.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit fadd7a6e616b89c7f4f7bfa7b824f290bab32c3c ]

The DCP driver does not obey cryptlen, when doing android CTS this
results in passing to hardware input stream lengths which are not
multiple of block size.

Add a check to prevent future erroneous stream lengths from reaching the
hardware and adjust the scatterlist walking code to obey cryptlen.

Also properly copy-out the IV for chaining.
Signed-off-by: NRadu Solea <radu.solea@nxp.com>
Signed-off-by: NFranck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: NLeonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c709eebaf5c5faa8a0f140355f9cfe67e8f7afb1 ]

DCP writes at least 32 bytes in the output buffer instead of hash length
as documented. Add intermediate buffer to prevent write out of bounds.

When requested to produce null hashes DCP fails to produce valid output.
Add software workaround to bypass hardware and return valid output.
Signed-off-by: NRadu Solea <radu.solea@nxp.com>
Signed-off-by: NLeonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 97d49c59e219acac576e16293a6b8cb99302f62f ]

Fix warning when running with CONFIG_DMA_API_DEBUG_SG=y by allocating a
device_dma_parameters structure and filling in the max segment size.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit fa112cf1e8bc693d5a666b1c479a2859c8b6e0f1 ]

When building a 32-bit config which has the above MFD item as module
but OLPC_XO1_PM is enabled =y - which is bool, btw - the kernel fails
building with:

  ld: arch/x86/platform/olpc/olpc-xo1-pm.o: in function `xo1_pm_remove':
  /home/boris/kernel/linux/arch/x86/platform/olpc/olpc-xo1-pm.c:159: undefined reference to `mfd_cell_disable'
  ld: arch/x86/platform/olpc/olpc-xo1-pm.o: in function `xo1_pm_probe':
  /home/boris/kernel/linux/arch/x86/platform/olpc/olpc-xo1-pm.c:133: undefined reference to `mfd_cell_enable'
  make: *** [Makefile:1030: vmlinux] Error 1

Force MFD_CS5535 to y if OLPC_XO1_PM is enabled.
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: x86@kernel.org
Link: http://lkml.kernel.org/r/20181005131750.GA5366@zn.tnicSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9cf38d5559e813cccdba8b44c82cc46ba48d0896 ]

When SME is enabled in the first kernel, it needs to allocate decrypted
pages for kdump because when the kdump kernel boots, these pages need to
be accessed decrypted in the initial boot stage, before SME is enabled.

 [ bp: clean up text. ]
Signed-off-by: NLianbo Jiang <lijiang@redhat.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Reviewed-by: NTom Lendacky <thomas.lendacky@amd.com>
Cc: kexec@lists.infradead.org
Cc: tglx@linutronix.de
Cc: mingo@redhat.com
Cc: hpa@zytor.com
Cc: akpm@linux-foundation.org
Cc: dan.j.williams@intel.com
Cc: bhelgaas@google.com
Cc: baiyaowei@cmss.chinamobile.com
Cc: tiwai@suse.de
Cc: brijesh.singh@amd.com
Cc: dyoung@redhat.com
Cc: bhe@redhat.com
Cc: jroedel@suse.de
Link: https://lkml.kernel.org/r/20180930031033.22110-3-lijiang@redhat.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d3ae96c0e6b042a883927493351b2af6ee05e92c ]

Currently with GLINK_SSR enabled each fatal crash results in servicing
a crash from wdog as well. This is due to a race that occurs in setting
the running flag in the shutdown path. Fix this by moving the running
flag to the end of fatal interrupt handler.

Crash Logs:
qcom-q6v5-pil 4080000.remoteproc: fatal error without message
remoteproc remoteproc0: crash detected in 4080000.remoteproc: type fatal
	error
remoteproc remoteproc0: handling crash #1 in 4080000.remoteproc
remoteproc remoteproc0: recovering 4080000.remoteproc
qcom-q6v5-pil 4080000.remoteproc: watchdog without message
remoteproc remoteproc0: crash detected in 4080000.remoteproc: type watchdog
remoteproc:glink-edge: intent request timed out
qcom_glink_ssr remoteproc:glink-edge.glink_ssr.-1.-1: failed to send
	cleanup message
qcom_glink_ssr remoteproc:glink-edge.glink_ssr.-1.-1: timeout waiting
	for cleanup done message
qcom-q6v5-pil 4080000.remoteproc: timed out on wait
qcom-q6v5-pil 4080000.remoteproc: port failed halt
remoteproc remoteproc0: stopped remote processor 4080000.remoteproc
qcom-q6v5-pil 4080000.remoteproc: MBA booted, loading mpss
remoteproc remoteproc0: remote processor 4080000.remoteproc is now up
remoteproc remoteproc0: handling crash #2 in 4080000.remoteproc
remoteproc remoteproc0: recovering 4080000.remoteproc
qcom-q6v5-pil 4080000.remoteproc: port failed halt
remoteproc remoteproc0: stopped remote processor 4080000.remoteproc
qcom-q6v5-pil 4080000.remoteproc: MBA booted, loading mpss
remoteproc remoteproc0: remote processor 4080000.remoteproc is now up
Suggested-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NSibi Sankar <sibis@codeaurora.org>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit faeadbb64094757150a8c2a3175ca418dbdd472c ]

The remoteproc framework provides a sysfs file 'firmware'
for modifying the firmware image name from userspace. Add
an additional check to ensure NULL firmwares are errored
out right away, rather than getting a delayed error while
requesting a firmware during the start of a remoteproc
later on.
Tested-by: NArnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: NSuman Anna <s-anna@ti.com>
Signed-off-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit cf5eafbfa586d030f9321cee516b91d089e38280 ]

rely on uAPI headers in the current kernel tree, rather than requiring the
correct version installed on the test system. While at it, group all
sections in a single binary and test the 'section' parameter.
Reported-by: NLucas Bates <lucasb@mojatatu.com>
Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 701a6d6ac78c76083ddb7c6581fdbedd95093e11 ]

In revision 0x20, we use vlan id != 0 to check whether a vlan tag
has been offloaded, so vlan id 0 is not supported.

In revision 0x21, rx buffer descriptor adds two bits to indicate
whether one or more vlan tags have been offloaded, so vlan id 0
is valid now.

This patch seperates the handle for vlan id 0, add vlan id 0 support
for revision 0x21.

Fixes: 5b5455a9 ("net: hns3: Add STRP_TAGP field support for hardware revision 0x21")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e0940b34c40e95d1879691d2474d182c57aae0de ]

A crash in bman portal probing could not be triggered (as is the case
with qman portals) but it does make calls [1] into the bman driver so
lets make sure the bman portal probing happens after bman's.

[1]  bman_p_irqsource_add() (in bman) called by:
       init_pcfg() called by:
         bman_portal_probe()
Signed-off-by: NLaurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: NLi Yang <leoyang.li@nxp.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit dde27443211062e841806feaf690674b7c3a599f ]

A certain silead controller (Chip ID: 0x56810000) loses its firmware
after suspend, causing the resume to fail. This patch tries to load
the firmware, should a resume error occur and retries the resuming.
Signed-off-by: NJulian Sax <jsbc@gmx.de>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 20bbb312079494a406c10c90932e3c80837c9d94 ]

This is how userspace checks for touchscreen devices most reliably.
Signed-off-by: NMartin Kepplinger <martink@posteo.de>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e2115ace4196bcd2126446fb874bcfc90cba79be ]

And don't reimplement in the driver.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NShawn Guo <shawnguo@kernel.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c96c0f2683804b710531e7b754dcd02b5ded6d4a ]

And don't reimplement in the driver.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: NJon Hunter <jonathanh@nvidia.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit de82bb431855580ad659bfed3e858bd9dd12efd0 ]

And don't reimplement in the driver.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NAndy Gross <andy.gross@linaro.org>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f37b2bb6ac3e6ebf855d9d4f05cc6932a8e5b463 ]

And don't reimplement in the driver.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b524abcc01483b2ac093cc6a8a2a7375558d2b64 ]

When an io error is hit, it calls gfs2_io_error_bh_i for every
journal buffer it can't write. Since we changed gfs2_io_error_bh_i
recently to withdraw later in the cycle, it sends a flood of
errors to the console. This patch checks for the file system already
being withdrawn, and if so, doesn't send more messages. It doesn't
stop the flood of messages, but it slows it down and keeps it more
reasonable.
Signed-off-by: NBob Peterson <rpeterso@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c439d5c1e13dbf66cff53455432f21d4d0536c51 ]

If a receive is in progress or starts before the transmit has
a chance, then lower the Signal Free Time of the upcoming transmit
to no more than CEC_SIGNAL_FREE_TIME_NEW_INITIATOR.

This is per the specification requirements.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0929983e49c81c1d413702cd9b83bb06c4a2555c ]

Changing framerate right before streamon had no effect,
the new framerate value was taken into account only at
next streamon, fix this.
Signed-off-by: NHugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f4d34aa8c887a8a2d23ef546da0efa10e3f77241 ]
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Signed-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 44f411c353bf6d98d5a34f8f1b8605d43b2e50b8 ]

Running "./nfstest_delegation --runtest recall26" uncovers that
client doesn't recover the lock when we have an appending open,
where the initial open got a write delegation.

Instead of checking for the passed in open context against
the file lock's open context. Check that the state is the same.
Signed-off-by: NOlga Kornievskaia <kolga@netapp.com>
Signed-off-by: NTrond Myklebust <trond.myklebust@hammerspace.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 51a72ab7372d85c96104e58036f1b49ba11e5d2b ]

log_first_seq and console_seq are 64-bit unsigned integers.
Correct a wrong casting that might cut off the output.

Link: http://lkml.kernel.org/r/1538239553-81805-2-git-send-email-zhe.he@windriver.com
Cc: rostedt@goodmis.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NHe Zhe <zhe.he@windriver.com>
[sergey.senozhatsky@gmail.com: More descriptive commit message]
Reviewed-by: NSergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: NPetr Mladek <pmladek@suse.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e1eba2ea54a2de0e4c58d87270d25706bb77b844 ]

ARCH_BCM_63XX which is used by ARM-based DSL SoCs from Broadcom uses the
same controller, make it possible to select the STB driver and update
the Kconfig and help text a bit.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1da220e3a5d22fccda0bc8542997abc1d1741268 ]

clk_notifier_register() documentation states, that the provided notifier
callbacks associated with the notifier must not re-enter into the clk
framework by calling any top-level clk APIs. Fix this by replacing
clk_get_rate() calls with clk_hw_get_rate(), which is safe in this
context.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d32dd2a1a0f80edad158c9a1ba5f47650d9504a0 ]

The bit of GATE_BUS_PERIS1 for CLK_SECKEY is just reserved on
exynos5422/5800, not exynos5420. Define gate clk for exynos5420 to
handle the bit only on exynos5420.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
[m.szyprow: rewrote commit subject]
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 70da9ee80228e6d98fd68e3c1db124c4461d283c ]

SoC clock drivers should suspend after every other drivers in the system,
which are using clocks and resume before them. The last stage for calling
suspend device callbacks is NOIRQ stage and there exists driver, which use
that state (dwmmc-exynos), so Exynos5433 clocks driver should also use it.
During the same stage, clocks driver will be always suspended after its
clients as a direct result of proper device probe order (deferred probe
reorders the suspend call sequence).
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NChanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NSylwester Nawrocki <snawrocki@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 35da3fe63b8647ce3cc52fccdf186a60710815fb ]

On disconnect wireless core attempts to remove all the supported keys.
Following cfg80211_ops conventions, firmware returns -ENOENT code
for the out-of-bound key indexes. This is a normal behavior,
so no need to report errors for this case.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit ab1c64a1d349cc7f1090a60ce85a53298e3d371d ]

Driver retrieves information about supported extended capabilities
from wireless card. However this information is not propagated
further to Linux wireless core. Fix this by setting extended
capabilities fields of wiphy structure.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d5657b709e2a92a0e581109010765d1d485580df ]

SGI should be passed to wireless core as a part of rate structure.
Otherwise wireless core performs incorrect rate calculation when
SGI is enabled in hardware but not reported to host.
Signed-off-by: NSergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>