Request the GPIO by index through the consumer API. For now, use a quick
hack to store the already requested ones, simply because I have no idea
whether this actually works or not, and I have no way to test it.

v2 by Mika: switch *NULL* to *"panel"* when requesting gpio for MIPI/DSI
panel.
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480923034-21916-1-git-send-email-mika.kahola@intel.com

In preparation to using a generic API in the DRM core for continuous CRC
generation, move the related code out of i915_debugfs.c into a new file.

Eventually, only the Intel-specific code will remain in this new file.

v2: Rebased.

v6: Rebased.

v7: Fix whitespace issue.

v9: Have intel_display_crc_init accept a drm_i915_private instead.

v12: Rebased.
Signed-off-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Reviewed-by: NEmil Velikov <emil.velikov@collabora.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1481545788-18194-1-git-send-email-tomeu.vizoso@collabora.com

Currently the backlight controller is taken as 0. It needs to derive
value from the VBT. Adding the necessary changes.

v2 by Jani:
 - drop obsolete comments, drop redundant initialization (Bob)
 - merge debug logging into one
Signed-off-by: NUma Shankar <uma.shankar@intel.com>
Signed-off-by: NVidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Tested-by: NBob Paauwe <bob.j.paauwe@intel.com>
Tested-by: NMika Kahola <mika.kahola@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481189178-426-1-git-send-email-jani.nikula@intel.com

Some object retain an extra pin whilst they are active (e.g. contexts).
This excludes them from being considered for eviction unless we idle the
GPU. If before we look at the active list, we retire beforehand we can
hopefully remove a few excess pins and reduce the amount of searching
required.

v2: Similar principle applies to evict_for_vma
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161209150555.602-1-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

In commit a4f5ea64 ("drm/i915: Refactor object page API"), I
reordered the object->pages teardown to be more friendly wrt to a
separate obj->mm.lock. However, I overlooked the phys object and left it
with a dangling use-after-free of its phys_handle. Move the allocation
of the phys handle to get_pages and it release to put_pages to prevent
the invalid access and to improve symmetry.

v2: Add commentary about always aligning to page size.

Testcase: igt/drv_selftest/objects
Reported-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Fixes: a4f5ea64 ("drm/i915: Refactor object page API")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161207133411.8028-1-chris@chris-wilson.co.uk

For PSR2 , as per spec, PSR2_CTL bit 31 to be set.
for psr1, bit 31 in SRD_CTL to be set. Reporting
"HW Enabled & Active bit" status for psr2 from SRD_CTL
gives  wrong status.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Signed-off-by: Nvathsala nagaraju <vathsala.nagaraju@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481307129-29354-1-git-send-email-vathsala.nagaraju@intel.com

This adds a 'Perf' section to i915.rst with the following sub sections:
- Overview
- Comparison with Core Perf
- i915 Driver Entry Points
- i915 Perf Stream
- i915 Perf Observation Architecture Stream
- All i915 Perf Internals

v2:
    section headers in i915.rst (Daniel Vetter)
    missing symbol docs + other fixups (Matthew Auld)
Signed-off-by: NRobert Bragg <robert@sixbynine.org>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161207214033.3581-1-robert@sixbynine.org

According to the previous patch, it's possible atm that we call
intel_do_sagv_disable() only once during the 1ms period and time out if
that call fails. As opposed to this the spec says that we need to keep
retrying this request for a 1ms duration, so let's do this similarly to
the CDCLK change notification request.

v4-5:
- Rebased on the reply_mask, reply change.
v6:
- Remove w/s change. (Lyude)
- Rebased on the timeout_base argument change.

Cc: Lyude <cpaul@redhat.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 656d1b89 ("drm/i915/skl: Add support for the SAGV, fix underrun hangs")
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Lyude <lyude@redhat.com> (v4)
Link: http://patchwork.freedesktop.org/patch/msgid/1480955258-26311-2-git-send-email-imre.deak@intel.com

commit 848496e5
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date:   Wed Jul 13 16:32:03 2016 +0300

    drm/i915: Wait up to 3ms for the pcu to ack the cdclk change request on SKL

increased the timeout to match the spec, but we still see a timeout on
at least one SKL. A CDCLK change request following the failed one will
succeed nevertheless.

I could reproduce this problem easily by running kms_pipe_crc_basic in a
loop. In all failure cases _wait_for() was pre-empted for >3ms and so in
the worst case - when the pre-emption happened right after calculating
timeout__ in _wait_for() - we called skl_cdclk_wait_for_pcu_ready() only
once which failed and so _wait_for() timed out. As opposed to this the
spec says to keep retrying the request for at most a 3ms period.

To fix this send the first request explicitly to guarantee that there is
3ms between the first and last request. Though this matches the spec, I
noticed that in rare cases this can still time out if we sent only a few
requests (in the worst case 2) _and_ PCODE is busy for some reason even
after a previous request and a 3ms delay. To work around this retry the
polling with pre-emption disabled to maximize the number of requests.
Also increase the timeout to 10ms to account for interrupts that could
reduce the number of requests. With this change I couldn't trigger
the problem.

v2:
- Use 1ms poll period instead of 10us. (Chris)
v3:
- Poll with pre-emption disabled to increase the number of request
  attempts. (Ville, Chris)
- Factor out a helper to poll, it's also needed by the next patch.
v4:
- Pass reply_mask, reply to skl_pcode_request(), instead of assuming the
  reply is generic. (Ville)
v5:
- List the request specific timeout values as code comment. (Ville)
v6:
- Try the poll first with preemption enabled.
- Add code comment about first request being queued by PCODE. (Art)
- Add timeout_base_ms argument. (Ville)
v7:
- Clarify code comment about first queued request. (Chris)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Art Runyan <arthur.j.runyan@intel.com>
Cc: <stable@vger.kernel.org> # v4.2- : 3b2c1710 : drm/i915: Wait up to 3ms
Cc: <stable@vger.kernel.org> # v4.2-
Fixes: 5d96d8af ("drm/i915/skl: Deinit/init the display at suspend/resume")
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=97929
Testcase: igt/kms_pipe_crc_basic/suspend-read-crc-pipe-B
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1480955258-26311-1-git-send-email-imre.deak@intel.com

Now that it is available we don't have to open code a similar
error message ourselves.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1481051053-29783-1-git-send-email-tvrtko.ursulin@linux.intel.com

Replace INTEL_ERR_OR_DBG_KMS macro with an intel_err_or_dbg_kms
function to shrink the code and rodata strings.

   text    data     bss     dec     hex filename
1271480   41831    2016 1315327  1411ff i915.ko.0
1265160   41831    2016 1309007  13f94f i915.ko.2

Total of ~6 KiB saving across text and strings.

v2:
 * Annotate the function for printf-style checking.
 * Rename to pipe_config_err. (Chris Wilson)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1481021420-5783-1-git-send-email-tvrtko.ursulin@linux.intel.com

Add WARN_ON to find_fw_domain to registers related to uninitialized
hardware.

v2:
- Print the uninitialized domains and register (Chris)

Cc: Imre Deak <imre.deak@intel.com>
Cc: Wang Elaine <elaine.wang@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1481120559-17413-1-git-send-email-joonas.lahtinen@linux.intel.com

Pineview deserves to use its own platform enum (which was already added,
unused, previously). IS_G33() no longer matches Pineview, and gets
replaced by IS_G33() || IS_PINEVIEW() or equivalent. Pineview is no
longer an outlier among platform definitions.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481143689-19672-1-git-send-email-jani.nikula@intel.com

This patch Adds a function to extract intel_crtc_state from the
atomic_state, if not available it returns NULL.

v2 (from Paulo):
 - Fix white space problem detected by checkpatch.
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-7-mahesh1.kumar@intel.com

This patch changes Watermak calculation to fixed point calculation.
Problem with current calculation is during plane_blocks_per_line
calculation we divide intermediate blocks with min_scanlines and
takes floor of the result because of integer operation.
hence we end-up assigning less blocks than required. Which leads to
flickers.

Changes since V1:
 - Add fixed point data type as per Paulo's review
Changes since V2:
 - use fixed_point instead of fp_16_16
Changes since V3:
 - rebase
Changes since V4 (from Paulo):
 - My original renaming suggestion was misunderstood, so implement it
 - Simplify fixed_16_16_to_u32 implementation
 - Fix indentation
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-6-mahesh1.kumar@intel.com

Display Workarounds #1141
IPC (Isoch Priority Control) may cause underflows.

KBL WA: When IPC is enabled, watermark latency values must be increased
by 4us across all levels. This brings level 0 up to 6us.

Changes since V1:
 - Add Workaround number in commit & code
Changes since V2 (from Paulo):
 - Bikeshed the WA tag so it looks like the others
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-4-mahesh1.kumar@intel.com

Display Workarounds #1135
If IPC is enabled in BXT, display underruns are observed.
WA: The Line Time programmed in the WM_LINETIME register should be
half of the actual calculated Line Time.

Programmed Line Time = 1/2*Calculated Line Time

Changes since V1:
 - Add Workaround number in commit & code
Changes since V2 (from Paulo):
 - Bikeshed white space and make the WA tag look like the others
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-3-mahesh1.kumar@intel.com

This patch adds variable to check for X_tiled & y_tiled planes, instead
of always checking against framebuffer-modifiers.

Changes:
 - Created separate patch as per Paulo's comment
 - Added x_tiled variable as well
Changes since V2:
 - Incorporate Paulo's comments
 - Rebase
Changes since V3 (from Paulo):
 - Bikeshed indentation
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NMahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201154940.24446-2-mahesh1.kumar@intel.com

Set the CHV_GPIO_GPIOEN bit when updating GPIOs from chv_exec_gpio.

Fixes: a0a6d4ff ("drm/i915/dsi: add support for gpio elements on CHV")
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201202925.12220-3-hdegoede@redhat.comSigned-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Looking at the ADF code from the Android kernel sources for a
cherrytrail tablet I noticed that it is calling the
MIPI_SEQ_ASSERT_RESET sequence from the panel prepare hook.

Until commit b1cb1bd2 ("drm/i915/dsi: update reset and power sequences
in panel prepare/unprepare hooks") the mainline i915 code was doing the
same. That commits effectively swaps the calling of MIPI_SEQ_ASSERT_RESET /
MIPI_SEQ_DEASSERT_RESET.

Looking at the naming of the sequences that is the right thing to do,
but the problem is, that the old mainline code and the ADF code was
actually calling the right sequence (tested on a cube iwork8 air tablet),
and the swapping of the calling breaks things.

This breakage was likely not noticed in testing because on cherrytrail,
currently chv_exec_gpio ends up disabling the gpio pins rather then
setting them (this is fixed in the next patch in this patch-set).

This commit fixes the swapping by fixing MIPI_SEQ_ASSERT/DEASSERT_RESET's
places in the enum defining them, so that their (new) names match their
actual use.

Changes in v2:
-Add a comment to the enum explaining that the assert/reassert names
 are swapped in the spec

Fixes: b1cb1bd2 ("drm/i915/dsi: update reset and power sequences...")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161202150128.29871-1-hdegoede@redhat.comSigned-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Avoid using DRM_ERROR for conditions userspace can trigger with a bad
config when opening a stream or from not reading data in a timely
fashion (whereby the OA buffer fills up). These conditions are tested
by i-g-t which treats error messages as failures if using the test
runner. This wasn't an issue while the i915-perf igt tests were being
run in isolation.

One message relating to seeing a spurious zeroed report was changed to
use DRM_NOTE instead of DRM_ERROR. Ideally this warning shouldn't be
seen, but it's not a serious problem if it is. Considering that the
tail margin mechanism is only a heuristic it's possible we might see
this from time to time.

Signed-off-by: Robert Bragg <robert@sixbynine.org:
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201172152.10893-1-robert@sixbynine.org

Each DSPARB register can house bits for two separate pipes, hence
we must protect the registers during reprogramming so that parallel
FIFO reconfigurations happening simultaneosly on multiple pipes won't
corrupt each others values.

We'll use a new spinlock for this instead of the wm_mutex since we'll
have to move the DSPARB programming to happen from the vblank evade
critical section, and we can't use mutexes in there.

v2: Document why we use a spinlock instead of a mutex (Maarten)

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480947208-18468-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Duplicating the PCI ID for IS_FOO checks is redundant for a bunch of
platforms. Simplify.
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/4f79321aca2e003a627ba8b6809af3716b7c25c9.1480520526.git.jani.nikula@intel.com

Distinguish them better.
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/987709804bc8fe55475e7481fcee03e7b86b1ba3.1480520526.git.jani.nikula@intel.com

Consistency FTW.
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/9ab811dc06570bd3fc05a917ade1bdc9bb805a75.1480520526.git.jani.nikula@intel.com

Add more consistency to our naming. Pineview remains the outlier. Keep
using code names for gen5+.

v2: rebased
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1481105584-23033-1-git-send-email-jani.nikula@intel.com

Move G33 and Pineview higher up in the list. Add a couple of blank lines
for OCD while at it.
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/ef4cc8e6ddf592c8c2769b84d4b88a5422d46ea5.1480520526.git.jani.nikula@intel.com

The platform flags in device info are (mostly) mutually
exclusive. Replace the flags with an enum. Add the platform enum also
for platforms that previously didn't have a flag, and give them codename
logging in dmesg.

Pineview remains an exception, the platform being G33 for that.

v2: Sort enum by gen and date

v3: rebase on geminilake enabling
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480596595-3278-1-git-send-email-jani.nikula@intel.com

The firmware interface file was initially partially autogenerated, but
this is no longer the case.

It was never updated automatically, and a lot manual changes were
introduced since.

>From now on any changes to the firmware interface will be managed by
hand, which gives us flexibility when it comes to structure reuse
(HuC/GuC) and naming conventions.

Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Jeff Mcgee <jeff.mcgee@intel.com>
Cc: Sagar A. Kamble <sagar.a.kamble@intel.com>
Signed-off-by: NArkadiusz Hiler <arkadiusz.hiler@intel.com>
Reviewed-by: NJeff McGee <jeff.mcgee@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480953869-25267-1-git-send-email-arkadiusz.hiler@intel.com

As it already says in the comment block...
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161206015704.12654-1-michel.thierry@intel.com

Instead of being hidden in sanitize_enable_ppgtt.
It also seems to be the place to do so nowadays.
Signed-off-by: NMichel Thierry <michel.thierry@intel.com>
Reviewed-by: NMichał Winiarski <michal.winiarski@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

On all platforms we now always read the contents of buffers via the GTT,
i.e. using WC cpu access. Reads are slow, but they can be accelerated
with an internal read buffer using sse4.1 (movntqda). This is our
i915_memcpy_from_wc() routine which also checks for sse4.1 support and
so we can fallback to using a regular slow memcpy if we need to.

When compressing the pages, the reads are currently done inside zlib's
fill_window() routine and so we must copy the page into a temporary
which is then already inside the CPU cache and fast for zlib's
compression. When not compressing the pages, we don't need a temporary
and can just use the accelerated read from WC into the destination.

v2: Use zstream locals to reduce diff and allocate the additional
temporary storage only if sse4.1 is supported.
v3: Use length=0 for the sse4.1 support check
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161206124051.17040-1-chris@chris-wilson.co.ukReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Use BUILD_BUG_ON_INVALID(expr) in GEM_BUG_ON when building without
DEBUG_GEM. This means the compiler can now check the validity of expr
without generating any code, in turn preventing us from inadvertently
breaking the build when DEBUG_GEM is not enabled.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161202184750.3843-1-matthew.auld@intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

list.h provides a macro for updating the next element in a safe
list-iter, so let's use it so that it is hopefully clearer to the reader
about the unusual behaviour, and also easier to grep.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-6-chris@chris-wilson.co.uk

Only once the debugobject symbols are exported can we enable support for
debugging swfences when i915 is built as a module. Requires commit
2617fdca3f68 ("lib/debugobjects: export for use in modules")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-5-chris@chris-wilson.co.uk

As we use debugobjects to track the lifetime of fences within our atomic
state, we ideally want to mark those objects as freed along with their
containers. This merits us hookin into config->funcs->atomic_state_free
for this purpose.

This allows us to enable debugobjects for sw-fences without triggering
known issues.

Fixes: fc158405 ("drm/i915: Integrate i915_sw_fence with debugobjects")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-4-chris@chris-wilson.co.uk

We can replace a couple of tests with an assertion that the passed in
node is already allocated (as matches the existing call convention) and
by a small bit of refactoring we can bring the line lengths to under
80cols.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-3-chris@chris-wilson.co.uk

Soft-pinning depends upon being able to check for availabilty of an
interval and evict overlapping object from a drm_mm range manager very
quickly. Currently it uses a linear list, and so performance is dire and
not suitable as a general replacement. Worse, the current code will oops
if it tries to evict an active buffer.

It also helps if the routine reports the correct error codes as expected
by its callers and emits a tracepoint upon use.

For posterity since the wrong patch was pushed (i.e. that missed these
key points and had known bugs), this is the changelog that should have
been on commit 506a8e87 ("drm/i915: Add soft-pinning API for
execbuffer"):

Userspace can pass in an offset that it presumes the object is located
at. The kernel will then do its utmost to fit the object into that
location. The assumption is that userspace is handling its own object
locations (for example along with full-ppgtt) and that the kernel will
rarely have to make space for the user's requests.

This extends the DRM_IOCTL_I915_GEM_EXECBUFFER2 to do the following:
* if the user supplies a virtual address via the execobject->offset
  *and* sets the EXEC_OBJECT_PINNED flag in execobject->flags, then
  that object is placed at that offset in the address space selected
  by the context specifier in execbuffer.
* the location must be aligned to the GTT page size, 4096 bytes
* as the object is placed exactly as specified, it may be used by this
  execbuffer call without relocations pointing to it

It may fail to do so if:
* EINVAL is returned if the object does not have a 4096 byte aligned
  address
* the object conflicts with another pinned object (either pinned by
  hardware in that address space, e.g. scanouts in the aliasing ppgtt)
  or within the same batch.
  EBUSY is returned if the location is pinned by hardware
  EINVAL is returned if the location is already in use by the batch
* EINVAL is returned if the object conflicts with its own alignment (as meets
  the hardware requirements) or if the placement of the object does not fit
  within the address space

All other execbuffer errors apply.

Presence of this execbuf extension may be queried by passing
I915_PARAM_HAS_EXEC_SOFTPIN to DRM_IOCTL_I915_GETPARAM and checking for
a reported value of 1 (or greater).

v2: Combine the hole/adjusted-hole ENOSPC checks
v3: More color, more splitting, more blurb.

Fixes: 506a8e87 ("drm/i915: Add soft-pinning API for execbuffer")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-2-chris@chris-wilson.co.uk

We need to distinguish between full i915_vma structs and simple
drm_mm_nodes when considering eviction (i.e. we must be careful not to
treat a mere drm_mm_node as a much larger i915_vma causing memory
corruption, if we are lucky). To do this, color these not-a-vma with -1
(I915_COLOR_UNEVICTABLE).

v2...v200: New name for -1.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161205142941.21965-1-chris@chris-wilson.co.uk

On my Cherrytrail CUBE iwork8 Air tablet PIPE-A would get stuck on loading
i915 at boot 1 out of every 3 boots, resulting in a non functional LCD.
Once the i915 driver has successfully loaded, the panel can be disabled /
enabled without hitting this issue.

The getting stuck is caused by vlv_init_display_clock_gating() clearing
the DPOUNIT_CLOCK_GATE_DISABLE bit in DSPCLK_GATE_D when called from
chv_pipe_power_well_ops.enable() on driver load, while a pipe is enabled
driving the DSI LCD by the BIOS.

Clearing this bit while DSI is in use is a known issue and
intel_dsi_pre_enable() / intel_dsi_post_disable() already set / clear it
as appropriate.

This commit modifies vlv_init_display_clock_gating() to leave the
DPOUNIT_CLOCK_GATE_DISABLE bit alone fixing the pipe getting stuck.

Changes in v2:
-Replace PIPE-A with "a pipe" or "the pipe" in the commit msg and
comment

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=97330
Cc: stable@vger.kernel.org
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161202142904.25613-1-hdegoede@redhat.comSigned-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>