[ Upstream commit c5dbe60664b3660f5ac5854e21273ea2e7ff698f ]

Skip resetting paRAM slots marked as reserved as they might be used by
other cores.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190823125618.8133-2-peter.ujfalusi@ti.comSigned-off-by: NVinod Koul <vkoul@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 07f1a6850c5d5a65c917c3165692b5179ac4cb6b ]

When run test case:
  mdadm -CR /dev/md1 -l 1 -n 4 /dev/sd[a-d] --assume-clean --bitmap=internal
  mdadm -S /dev/md1
  mdadm -A /dev/md1 /dev/sd[b-c] --run --force

  mdadm --zero /dev/sda
  mdadm /dev/md1 -a /dev/sda

  echo offline > /sys/block/sdc/device/state
  echo offline > /sys/block/sdb/device/state
  sleep 5
  mdadm -S /dev/md1

  echo running > /sys/block/sdb/device/state
  echo running > /sys/block/sdc/device/state
  mdadm -A /dev/md1 /dev/sd[a-c] --run --force

mdadm run fail with kernel message as follow:
[  172.986064] md: kicking non-fresh sdb from array!
[  173.004210] md: kicking non-fresh sdc from array!
[  173.022383] md/raid1:md1: active with 0 out of 4 mirrors
[  173.022406] md1: failed to create bitmap (-5)

In fact, when active disk in raid1 array less than one, we
need to return fail in raid1_run().
Reviewed-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NYufen Yu <yuyufen@huawei.com>
Signed-off-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6e4d91aa071810deac2cd052161aefb376ecf04e ]

At boot time, the acpi_power_meter driver logs the following error level
message: "Ignoring unsafe software power cap". Having read about it from
a few sources, it seems that the error message can be quite misleading.

While the message can imply that Linux is ignoring the fact that the
system is operating in potentially dangerous conditions, the truth is
the driver found an ACPI_PMC object that supports software power
capping. The driver simply decides not to use it, perhaps because it
doesn't support the object.

The best solution is probably changing the log level from error to warning.
All sources I have found, regarding the error, have downplayed its
significance. There is not much of a reason for it to be on error level,
while causing potential confusions or misinterpretations.
Signed-off-by: NWang Shenran <shenran268@gmail.com>
Link: https://lore.kernel.org/r/20190724080110.6952-1-shenran268@gmail.comSigned-off-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit a22a9602b88fabf10847f238ff81fde5f906fef7 ]

The race was when a thread using closure_sync() notices cl->s->done == 1
before the thread calling closure_put() calls wake_up_process(). Then,
it's possible for that thread to return and exit just before
wake_up_process() is called - so we're trying to wake up a process that
no longer exists.

rcu_read_lock() is sufficient to protect against this, as there's an rcu
barrier somewhere in the process teardown path.
Signed-off-by: NKent Overstreet <kent.overstreet@gmail.com>
Acked-by: NColy Li <colyli@suse.de>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 29b49958cf73b439b17fa29e9a25210809a6c01c ]

In acpi_pci_irq_enable(), 'entry' is allocated by kzalloc() in
acpi_pci_irq_check_entry() (invoked from acpi_pci_irq_lookup()). However,
it is not deallocated if acpi_pci_irq_valid() returns false, leading to a
memory leak. To fix this issue, free 'entry' before returning 0.

Fixes: e237a551 ("x86/ACPI/PCI: Recognize that Interrupt Line 255 means "not connected"")
Signed-off-by: NWenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 03d1571d9513369c17e6848476763ebbd10ec2cb ]

In cm_write(), 'buf' is allocated through kzalloc(). In the following
execution, if an error occurs, 'buf' is not deallocated, leading to memory
leaks. To fix this issue, free 'buf' before returning the error.

Fixes: 526b4af4 ("ACPI: Split out custom_method functionality into an own driver")
Signed-off-by: NWenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 5b0eeeaa37615df37a9a30929b73e9defe61ca84 ]

Commit aff138bf ("ARM: dts: exynos: Add TMU nodes regulator supply
for Peach boards") assigned LDO10 to Exynos Thermal Measurement Unit,
but it turned out that it supplies also some other critical parts and
board freezes/crashes when it is turned off.

The mentioned commit made Exynos TMU a consumer of that regulator and in
typical case Exynos TMU driver keeps it enabled from early boot. However
there are such configurations (example is multi_v7_defconfig), in which
some of the regulators are compiled as modules and are not available
from early boot. In such case it may happen that LDO10 is turned off by
regulator core, because it has no consumers yet (in this case consumer
drivers cannot get it, because the supply regulators for it are not yet
available). This in turn causes the board to crash. This patch restores
'always-on' property for the LDO10 regulator.

Fixes: aff138bf ("ARM: dts: exynos: Add TMU nodes regulator supply for Peach boards")
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e97fd1383cd77c467d2aed7fa4e596789df83977 ]

To be compliant with XDG user directory layout, the user's plugin
directory is changed from ~/.traceevent/plugins to
~/.local/lib/traceevent/plugins/
Suggested-by: NPatrick McLean <chutzpah@gentoo.org>
Signed-off-by: NTzvetomir Stoyanov <tstoyanov@vmware.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Patrick McLean <chutzpah@gentoo.org>
Cc: linux-trace-devel@vger.kernel.org
Link: https://lore.kernel.org/linux-trace-devel/20190313144206.41e75cf8@patrickm/
Link: http://lore.kernel.org/linux-trace-devel/20190801074959.22023-4-tz.stoyanov@gmail.com
Link: http://lore.kernel.org/lkml/20190805204355.344622683@goodmis.orgSigned-off-by: NSteven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0d87308cca2c124f9bce02383f1d9632c9be89c4 ]

In commit 14bd9a607f90 ("iommu/iova: Separate atomic variables
to improve performance") Jinyu Qi identified that the atomic_cmpxchg()
in queue_iova() was causing a performance loss and moved critical fields
so that the false sharing would not impact them.

However, avoiding the false sharing in the first place seems easy.
We should attempt the atomic_cmpxchg() no more than 100 times
per second. Adding an atomic_read() will keep the cache
line mostly shared.

This false sharing came with commit 9a005a80
("iommu/iova: Add flush timer").
Signed-off-by: NEric Dumazet <edumazet@google.com>
Fixes: 9a005a80 ('iommu/iova: Add flush timer')
Cc: Jinyu Qi <jinyuqi@huawei.com>
Cc: Joerg Roedel <jroedel@suse.de>
Acked-by: NRobin Murphy <robin.murphy@arm.com>
Signed-off-by: NJoerg Roedel <jroedel@suse.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c312ef176399e04fc5f7f2809d9a589751fbf6d9 ]

The Linux ahci driver has historically implemented a configuration fixup
for platforms / platform-firmware that fails to enable the ports prior
to OS hand-off at boot. The fixup was originally implemented way back
before ahci moved from drivers/scsi/ to drivers/ata/, and was updated in
2007 via commit 49f29090 "ahci: update PCS programming". The quirk
sets a port-enable bitmap in the PCS register at offset 0x92.

This quirk could be applied generically up until the arrival of the
Denverton (DNV) platform. The DNV AHCI controller architecture supports
more than 6 ports and along with that the PCS register location and
format were updated to allow for more possible ports in the bitmap. DNV
AHCI expands the register to 32-bits and moves it to offset 0x94.

As it stands there are no known problem reports with existing Linux
trying to set bits at offset 0x92 which indicates that the quirk is not
applicable. Likely it is not applicable on a wider range of platforms,
but it is difficult to discern which platforms if any still depend on
the quirk.

Rather than try to fix the PCS quirk to consider the DNV register layout
instead require explicit opt-in. The assumption is that the OS driver
need not touch this register, and platforms can be added with a new
boad_ahci_pcs7 board-id when / if problematic platforms are found in the
future. The logic in ahci_intel_pcs_quirk() looks for all Intel AHCI
instances with "legacy" board-ids and otherwise skips the quirk if the
board was matched by class-code.
Reported-by: NStephen Douthit <stephend@silicom-usa.com>
Cc: Christoph Hellwig <hch@infradead.org>
Reviewed-by: NStephen Douthit <stephend@silicom-usa.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3d708895325b78506e8daf00ef31549476e8586a ]

When running heavy memory pressure workloads, the system is throwing
endless warnings,

smartpqi 0000:23:00.0: AMD-Vi: IOMMU mapping error in map_sg (io-pages:
5 reason: -12)
Hardware name: HPE ProLiant DL385 Gen10/ProLiant DL385 Gen10, BIOS A40
07/10/2019
swapper/10: page allocation failure: order:0, mode:0xa20(GFP_ATOMIC),
nodemask=(null),cpuset=/,mems_allowed=0,4
Call Trace:
 <IRQ>
 dump_stack+0x62/0x9a
 warn_alloc.cold.43+0x8a/0x148
 __alloc_pages_nodemask+0x1a5c/0x1bb0
 get_zeroed_page+0x16/0x20
 iommu_map_page+0x477/0x540
 map_sg+0x1ce/0x2f0
 scsi_dma_map+0xc6/0x160
 pqi_raid_submit_scsi_cmd_with_io_request+0x1c3/0x470 [smartpqi]
 do_IRQ+0x81/0x170
 common_interrupt+0xf/0xf
 </IRQ>

because the allocation could fail from iommu_map_page(), and the volume
of this call could be huge which may generate a lot of serial console
output and cosumes all CPUs.

Fix it by silencing the warning in this call site, and there is still a
dev_err() later to notify the failure.
Signed-off-by: NQian Cai <cai@lca.pw>
Signed-off-by: NJoerg Roedel <jroedel@suse.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 6af86bdb8ad41f4cf1292d3b10857dc322758328 ]

MOTU 4pre was launched in 2012 by MOTU, Inc. This commit allows userspace
applications can transmit and receive PCM frames and MIDI messages for
this model via ALSA PCM interface and RawMidi/Sequencer interfaces.

The device supports MOTU protocol version 3. Unlike the other devices, the
device is simply designed. The size of data block is fixed to 10 quadlets
during available sampling rates (44.1 - 96.0 kHz). Each data block
includes 1 source packet header, 2 data chunks for messages, 8 data chunks
for PCM samples and 2 data chunks for padding to quadlet alignment. The
device has no MIDI, optical, BNC and AES/EBU interfaces.

Like support for the other MOTU devices, the quality of playback sound
is not enough good with periodical noise yet.

$ python2 crpp < ~/git/am-config-rom/motu/motu-4pre.img
               ROM header and bus information block
               -----------------------------------------------------------------
400  041078cc  bus_info_length 4, crc_length 16, crc 30924
404  31333934  bus_name "1394"
408  20ff7000  irmc 0, cmc 0, isc 1, bmc 0, cyc_clk_acc 255, max_rec 7 (256)
40c  0001f200  company_id 0001f2     |
410  000a41c5  device_id 00000a41c5  | EUI-64 0001f200000a41c5

               root directory
               -----------------------------------------------------------------
414  0004ef04  directory_length 4, crc 61188
418  030001f2  vendor
41c  0c0083c0  node capabilities per IEEE 1394
420  d1000002  --> unit directory at 428
424  8d000005  --> eui-64 leaf at 438

               unit directory at 428
               -----------------------------------------------------------------
428  0003ceda  directory_length 3, crc 52954
42c  120001f2  specifier id
430  13000045  version
434  17103800  model

               eui-64 leaf at 438
               -----------------------------------------------------------------
438  0002d248  leaf_length 2, crc 53832
43c  0001f200  company_id 0001f2     |
440  000a41c5  device_id 00000a41c5  | EUI-64 0001f200000a41c5
Signed-off-by: NTakashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit e01f91dff91c7b16a6e3faf2565017d497a73f83 ]

ANA log parsing invokes nvme_update_ana_state() per ANA group desc.
This updates the state of namespaces with nsids in desc->nsids[].

Both ctrl->namespaces list and desc->nsids[] array are sorted by nsid.
Hence nvme_update_ana_state() performs a single walk over ctrl->namespaces:
- if current namespace matches the current desc->nsids[n],
  this namespace is updated, and n is incremented.
- the process stops when it encounters the end of either
  ctrl->namespaces end or desc->nsids[]

In case desc->nsids[n] does not match any of ctrl->namespaces,
the remaining nsids following desc->nsids[n] will not be updated.
Such situation was considered abnormal and generated WARN_ON_ONCE.

However ANA log MAY contain nsids not (yet) found in ctrl->namespaces.
For example, lets consider the following scenario:
- nvme0 exposes namespaces with nsids = [2, 3] to the host
- a new namespace nsid = 1 is added dynamically
- also, a ANA topology change is triggered
- NS_CHANGED aen is generated and triggers scan_work
- before scan_work discovers nsid=1 and creates a namespace, a NOTICE_ANA
  aen was issues and ana_work receives ANA log with nsids=[1, 2, 3]

Result: ana_work fails to update ANA state on existing namespaces [2, 3]

Solution:
Change the way nvme_update_ana_state() namespace list walk
checks the current namespace against desc->nsids[n] as follows:
a) ns->head->ns_id < desc->nsids[n]: keep walking ctrl->namespaces.
b) ns->head->ns_id == desc->nsids[n]: match, update the namespace
c) ns->head->ns_id >= desc->nsids[n]: skip to desc->nsids[n+1]

This enables correct operation in the scenario described above.
This also allows ANA log to contain nsids currently invisible
to the host, i.e. inactive nsids.
Signed-off-by: NAnton Eidelman <anton@lightbitslabs.com>
Reviewed-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 3bec2e3754becebd4c452999adb49bc62c575ea4 ]

In nvme spec 1.3 there is a definition for data write/read counters
from SMART log, (See section 5.14.1.2):
	This value is reported in thousands (i.e., a value of 1
	corresponds to 1000 units of 512 bytes read) and is rounded up.

However, in nvme target where value is reported with actual units,
but not thousands of units as the spec requires.
Signed-off-by: NTom Wu <tomwu@mellanox.com>
Reviewed-by: NIsrael Rukshin <israelr@mellanox.com>
Reviewed-by: NMax Gurtovoy <maxg@mellanox.com>
Reviewed-by: NChaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NSagi Grimberg <sagi@grimberg.me>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 825d0b73cd7526b0bb186798583fae810091cbac ]

pti_clone_pmds() assumes that the supplied address is either:

 - properly PUD/PMD aligned
or
 - the address is actually mapped which means that independently
   of the mapping level (PUD/PMD/PTE) the next higher mapping
   exists.

If that's not the case the unaligned address can be incremented by PUD or
PMD size incorrectly. All callers supply mapped and/or aligned addresses,
but for the sake of robustness it's better to handle that case properly and
to emit a warning.

[ tglx: Rewrote changelog and added WARN_ON_ONCE() ]
Signed-off-by: NSong Liu <songliubraving@fb.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NIngo Molnar <mingo@kernel.org>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/alpine.DEB.2.21.1908282352470.1938@nanos.tec.linutronix.deSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 696d05225cebffd172008d212657be90e823eac0 ]

The test case is
arecord -Dhw:0 -d 10 -f S16_LE -r 48000 -c 2 temp.wav &
aplay -Dhw:0 -d 30 -f S16_LE -r 48000 -c 2 test.wav

There will be error after end of arecord:
aplay: pcm_write:2051: write error: Input/output error

Capture and Playback work in parallel in master mode, one
substream stops, the other substream is impacted, the
reason is that clock is disabled wrongly.

The clock's reference count is not increased when second
substream starts, the hw_param() function returns in the
beginning because first substream is enabled, then in end
of first substream, the hw_free() disables the clock.

This patch is to move the clock enablement to the place
before checking of the device enablement in hw_param().
Signed-off-by: NShengjiu Wang <shengjiu.wang@nxp.com>
Link: https://lore.kernel.org/r/1567012817-12625-1-git-send-email-shengjiu.wang@nxp.comSigned-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 990784b57731192b7d90c8d4049e6318d81e887d ]

When PTI is disabled at boot time either because the CPU is not affected or
PTI has been disabled on the command line, the boot code still calls into
pti_finalize() which then unconditionally invokes:

     pti_clone_entry_text()
     pti_clone_kernel_text()

pti_clone_kernel_text() was called unconditionally before the 32bit support
was added and 32bit added the call to pti_clone_entry_text().

The call has no side effects as cloning the page tables into the available
second one, which was allocated for PTI does not create damage. But it does
not make sense either and in case that this functionality would be extended
later this might actually lead to hard to diagnose issues.

Neither function should be called when PTI is runtime disabled. Make the
invocation conditional.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NDave Hansen <dave.hansen@linux.intel.com>
Acked-by: NIngo Molnar <mingo@kernel.org>
Acked-by: NSong Liu <songliubraving@fb.com>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Link: https://lkml.kernel.org/r/20190828143124.063353972@linutronix.deSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f32c7a8e45105bd0af76872bf6eef0438ff12fb2 ]

While the MMUs is disabled, I-cache speculation can result in
instructions being fetched from the PoC. During boot we may patch
instructions (e.g. for alternatives and jump labels), and these may be
dirty at the PoU (and stale at the PoC).

Thus, while the MMU is disabled in the KPTI pagetable fixup code we may
load stale instructions into the I-cache, potentially leading to
subsequent crashes when executing regions of code which have been
modified at runtime.

Similarly to commit:

  8ec41987 ("arm64: mm: ensure patched kernel text is fetched from PoU")

... we can invalidate the I-cache after enabling the MMU to prevent such
issues.

The KPTI pagetable fixup code itself should be clean to the PoC per the
boot protocol, so no maintenance is required for this code.
Signed-off-by: NMark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: NJames Morse <james.morse@arm.com>
Signed-off-by: NWill Deacon <will@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 743dac494d61d991967ebcfab92e4f80dc7583b3 ]

On x86, CPUs are limited in the number of interrupts they can have affined
to them as they only support 256 interrupt vectors per CPU. 32 vectors are
reserved for the CPU and the kernel reserves another 22 for internal
purposes. That leaves 202 vectors for assignement to devices.

When an interrupt is set up or the affinity is changed by the kernel or the
administrator, the vector assignment code attempts to honor the requested
affinity mask. If the vector space on the CPUs in that affinity mask is
exhausted the code falls back to a wider set of CPUs and assigns a vector
on a CPU outside of the requested affinity mask silently.

While the effective affinity is reflected in the corresponding
/proc/irq/$N/effective_affinity* files the silent breakage of the requested
affinity can lead to unexpected behaviour for administrators.

Add a pr_warn() when this happens so that adminstrators get at least
informed about it in the syslog.

[ tglx: Massaged changelog and made the pr_warn() more informative ]

Reported-by: djuran@redhat.com
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: djuran@redhat.com
Link: https://lkml.kernel.org/r/20190822143421.9535-1-nhorman@tuxdriver.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 77c84dd1881d0f0176cb678d770bfbda26c54390 ]

Fast switching path only emits an event for the CPU of interest, whereas the
regular path emits an event for all the CPUs that had their frequency changed,
i.e. all the CPUs sharing the same policy.

With the current behavior, looking at cpu_frequency event for a given CPU that
is using the fast switching path will not give the correct frequency signal.
Signed-off-by: NDouglas RAILLARD <douglas.raillard@arm.com>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 4c4cdc4c63853fee48c02e25c8605fb65a6c9924 ]

According to the ACPI 6.3 specification, the _PSD method is optional
when using CPPC.  The underlying assumption is that each CPU can change
frequency independently from all other CPUs; _PSD is provided to tell
the OS that some processors can NOT do that.

However, the acpi_get_psd() function returns ENODEV if there is no _PSD
method present, or an ACPI error status if an error occurs when evaluating
_PSD, if present.  This makes _PSD mandatory when using CPPC, in violation
of the specification, and only on Linux.

This has forced some firmware writers to provide a dummy _PSD, even though
it is irrelevant, but only because Linux requires it; other OSPMs follow
the spec.  We really do not want to have OS specific ACPI tables, though.

So, correct acpi_get_psd() so that it does not return an error if there
is no _PSD method present, but does return a failure when the method can
not be executed properly.  This allows _PSD to be optional as it should
be.
Signed-off-by: NAl Stone <ahs3@redhat.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f972d02fee2496024cfd6f59021c9d89d54922a6 ]

This patch fix setting table of Headphone mixer volume.
Current code uses 4 ... 7 values but these values are prohibited.

Correct settings are the following:
  0000 -12dB
  0001 -10.5dB
  0010 -9dB
  0011 -7.5dB
  0100 -6dB
  1000 -4.5dB
  1001 -3dB
  1010 -1.5dB
  1011 0dB
Signed-off-by: NKatsuhiro Suzuki <katsuhiro@katsuster.net>
Reviewed-by: NDaniel Drake <drake@endlessm.com>
Link: https://lore.kernel.org/r/20190826153900.25969-1-katsuhiro@katsuster.netSigned-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 093347abc7a4e0490e3c962ecbde2dc272a8f708 ]

As pointed by cppcheck:

	[drivers/media/i2c/ov9650.c:706]: (error) Shifting by a negative value is undefined behaviour
	[drivers/media/i2c/ov9650.c:707]: (error) Shifting by a negative value is undefined behaviour
	[drivers/media/i2c/ov9650.c:721]: (error) Shifting by a negative value is undefined behaviour

Prevent mangling with gains with invalid values.

As pointed by Sylvester, this should never happen in practice,
as min value of V4L2_CID_GAIN control is 16 (gain is always >= 16
and m is always >= 0), but it is too hard for a static analyzer
to get this, as the logic with validates control min/max is
elsewhere inside V4L2 core.
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit b92675f4a9c02dd78052645597dac9e270679ddf ]

While tracing a program that calls isatty(3), I noticed that strace
reported TCGETS for the request argument of the underlying ioctl(2)
syscall while perf trace reported TCSETS. strace is corrrect. The bug in
perf was due to the tty ioctl beauty table starting at 0x5400 rather
than 0x5401.

Committer testing:

  Using augmented_raw_syscalls.o and settings to make 'perf trace'
  use strace formatting, i.e. with this in ~/.perfconfig

  # cat ~/.perfconfig
  [trace]
	add_events = /home/acme/git/linux/tools/perf/examples/bpf/augmented_raw_syscalls.c
	show_zeros = yes
	show_duration = no
	no_inherit = yes
	show_timestamp = no
	show_arg_names = no
	args_alignment = 40
	show_prefix = yes

  # strace -e ioctl stty > /dev/null
  ioctl(0, TCGETS, {B38400 opost isig icanon echo ...}) = 0
  ioctl(1, TIOCGWINSZ, 0x7fff8a9b0860)    = -1 ENOTTY (Inappropriate ioctl for device)
  ioctl(1, TCGETS, 0x7fff8a9b0540)        = -1 ENOTTY (Inappropriate ioctl for device)
  +++ exited with 0 +++
  #

Before:

  # perf trace -e ioctl stty > /dev/null
  ioctl(0, TCSETS, 0x7fff2cf79f20)        = 0
  ioctl(1, TIOCSWINSZ, 0x7fff2cf79f40)    = -1 ENOTTY (Inappropriate ioctl for device)
  ioctl(1, TCSETS, 0x7fff2cf79c20)        = -1 ENOTTY (Inappropriate ioctl for device)
  #

After:

  # perf trace -e ioctl stty > /dev/null
  ioctl(0, TCGETS, 0x7ffed0763920)        = 0
  ioctl(1, TIOCGWINSZ, 0x7ffed0763940)    = -1 ENOTTY (Inappropriate ioctl for device)
  ioctl(1, TCGETS, 0x7ffed0763620)        = -1 ENOTTY (Inappropriate ioctl for device)
  #
Signed-off-by: NBenjamin Peterson <benjamin@python.org>
Tested-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Fixes: 1cc47f2d ("perf trace beauty ioctl: Improve 'cmd' beautifier")
Link: http://lkml.kernel.org/r/20190823033625.18814-1-benjamin@python.orgSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9d802222a3405599d6e1984d9324cddf592ea1f4 ]

saa7134_i2c_eeprom_md7134_gate() function and the associated comment uses
an inverted i2c gate open / closed terminology.
Let's fix this.
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix alignment checkpatch warning]
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 1c770f0f52dca1a2323c594f01f5ec6f1dddc97f ]

In submit_urbs(), 'cam->sbuf[i].data' is allocated through kmalloc_array().
However, it is not deallocated if the following allocation for urbs fails.
To fix this issue, free 'cam->sbuf[i].data' if usb_alloc_urb() fails.
Signed-off-by: NWenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 42e64117d3b4a759013f77bbcf25ab6700e55de7 ]

If saa7146_register_device() fails, no cleanup is executed, leading to
memory/resource leaks. To fix this issue, perform necessary cleanup work
before returning the error.
Signed-off-by: NWenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 14d5511691e5290103bc480998bc322e68f139d4 ]

If cec_notifier_cec_adap_unregister() is called before
cec_unregister_adapter() then everything is OK (and this is the
case today). But if it is the other way around, then
cec_notifier_unregister() is called first, and that doesn't
set n->cec_adap to NULL.

So if e.g. cec_notifier_set_phys_addr() is called after
cec_notifier_unregister() but before cec_unregister_adapter()
then n->cec_adap points to an unregistered and likely deleted
cec adapter. So just set n->cec_adap->notifier and n->cec_adap
to NULL for rubustness.

Eventually cec_notifier_unregister will disappear and this will
be simplified substantially.
Signed-off-by: NHans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 2c2b20e0da89c76759ee28c6824413ab2fa3bfc6 ]

Regulators should be enabled before clocks to avoid h/w hang. This
require change in exynos_bus_probe() to move exynos_bus_parse_of()
after exynos_bus_parent_parse_of() and change in error handling.
Similar change is needed in exynos_bus_exit() where clock should be
disabled before regulators.
Signed-off-by: NKamil Konieczny <k.konieczny@partner.samsung.com>
Acked-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 0ef7c7cce43f6ecc2b96d447e69b2900a9655f7c ]

The devfreq passive governor registers and unregisters devfreq
transition notifiers on DEVFREQ_GOV_START/GOV_STOP using devm wrappers.

If devfreq itself is registered with devm then a warning is triggered on
rmmod from devm_devfreq_unregister_notifier. Call stack looks like this:

	devm_devfreq_unregister_notifier+0x30/0x40
	devfreq_passive_event_handler+0x4c/0x88
	devfreq_remove_device.part.8+0x6c/0x9c
	devm_devfreq_dev_release+0x18/0x20
	release_nodes+0x1b0/0x220
	devres_release_all+0x78/0x84
	device_release_driver_internal+0x100/0x1c0
	driver_detach+0x4c/0x90
	bus_remove_driver+0x7c/0xd0
	driver_unregister+0x2c/0x58
	platform_driver_unregister+0x10/0x18
	imx_devfreq_platdrv_exit+0x14/0xd40 [imx_devfreq]

This happens because devres_release_all will first remove all the nodes
into a separate todo list so the nested devres_release from
devm_devfreq_unregister_notifier won't find anything.

Fix the warning by calling the non-devm APIS for frequency notification.
Using devm wrappers is not actually useful for a governor anyway: it
relies on the devfreq core to correctly match the GOV_START/GOV_STOP
notifications.

Fixes: 99613311 ("PM / devfreq: Add new passive governor")
Signed-off-by: NLeonard Crestez <leonard.crestez@nxp.com>
Acked-by: NChanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 8a2eaab7daf03b23ac902481218034ae2fae5e16 ]

AMD Family 17h systems currently require address translation in order to
report the system address of a DRAM ECC error. This is currently done
before decoding the syndrome information. The syndrome information does
not depend on the address translation, so the proper EDAC csrow/channel
reporting can function without the address. However, the syndrome
information will not be decoded if the address translation fails.

Decode the syndrome information before doing the address translation.
The syndrome information is architecturally defined in MCA_SYND and can
be considered robust. The address translation is system-specific and may
fail on newer systems without proper updates to the translation
algorithm.

Fixes: 713ad546 ("EDAC, amd64: Define and register UMC error decode function")
Signed-off-by: NYazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190821235938.118710-6-Yazen.Ghannam@amd.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit f8be8e5680225ac9caf07d4545f8529b7395327f ]

AMD Family 17h systems support x4 and x16 DRAM devices. However, the
device type is not checked when setting mci.edac_ctl_cap.

Set the appropriate capability flag based on the device type.

Default to x8 DRAM device when neither the x4 or x16 bits are set.

 [ bp: reverse cpk_en check to save an indentation level. ]

Fixes: 2d09d8f3 ("EDAC, amd64: Determine EDAC MC capabilities on Fam17h")
Signed-off-by: NYazen Ghannam <yazen.ghannam@amd.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: "linux-edac@vger.kernel.org" <linux-edac@vger.kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Tony Luck <tony.luck@intel.com>
Link: https://lkml.kernel.org/r/20190821235938.118710-3-Yazen.Ghannam@amd.comSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit d9c5c083416500e95da098c01be092b937def7fa ]

Following the patch 'perf stat: Fix --no-scale', an alignment trap
happens in process_counter_values() on ARMv7 platforms due to the
attempt to copy non 64 bits aligned double words (pointed by 'count')
via a NEON vectored instruction ('vld1' with 64 bits alignment
constraint).

This patch sets a 64 bits alignment constraint on 'contents[]' field in
'struct xyarray' since the 'count' pointer used above points to such a
structure.
Signed-off-by: NGerald Baeza <gerald.baeza@st.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1566464769-16374-1-git-send-email-gerald.baeza@st.comSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit fcd5ce4b3936242e6679875a4d3c3acfc8743e15 ]

In dvb_create_media_entity(), 'dvbdev->entity' is allocated through
kzalloc(). Then, 'dvbdev->pads' is allocated through kcalloc(). However, if
kcalloc() fails, the allocated 'dvbdev->entity' is not deallocated, leading
to a memory leak bug. To fix this issue, free 'dvbdev->entity' before
returning -ENOMEM.
Signed-off-by: NWenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 692117c1f7a6770ed41dd8f277cd9fed1dfb16f1 ]

Warning when p == NULL and then proceeding and dereferencing p does not
make any sense as the kernel will crash with a NULL pointer dereference
right away.

Bailing out when p == NULL and returning an error code does not cure the
underlying problem which caused p to be NULL. Though it might allow to
do proper debugging.

Same applies to the clock id check in set_process_cpu_timer().

Clean them up and make them return without trying to do further damage.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NFrederic Weisbecker <frederic@kernel.org>
Link: https://lkml.kernel.org/r/20190819143801.846497772@linutronix.deSigned-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit c268e7adea52be0093de1164c425f3c8d8927770 ]

KASAN: global-out-of-bounds Read in dvb_pll_attach

Syzbot reported global-out-of-bounds Read in dvb_pll_attach, while
accessing id[dvb_pll_devcount], because dvb_pll_devcount was 65,
that is more than size of 'id' which is DVB_PLL_MAX(64).

Rather than increasing dvb_pll_devcount every time, use ida so that
numbers are allocated correctly. This does mean that no more than
64 devices can be attached at the same time, but this is more than
sufficient.

usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the
software demuxer
dvbdev: DVB: registering new adapter (774 Friio White ISDB-T USB2.0)
usb 1-1: media controller created
dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
tc90522 0-0018: Toshiba TC90522 attached.
usb 1-1: DVB: registering adapter 0 frontend 0 (Toshiba TC90522 ISDB-T
module)...
dvbdev: dvb_create_media_entity: media entity 'Toshiba TC90522 ISDB-T
module' registered.
==================================================================
BUG: KASAN: global-out-of-bounds in dvb_pll_attach+0x6c5/0x830
drivers/media/dvb-frontends/dvb-pll.c:798
Read of size 4 at addr ffffffff89c9e5e0 by task kworker/0:1/12

CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.2.0-rc6+ #13
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
  __dump_stack lib/dump_stack.c:77 [inline]
  dump_stack+0xca/0x13e lib/dump_stack.c:113
  print_address_description+0x67/0x231 mm/kasan/report.c:188
  __kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
  kasan_report+0xe/0x20 mm/kasan/common.c:614
  dvb_pll_attach+0x6c5/0x830 drivers/media/dvb-frontends/dvb-pll.c:798
  dvb_pll_probe+0xfe/0x174 drivers/media/dvb-frontends/dvb-pll.c:877
  i2c_device_probe+0x790/0xaa0 drivers/i2c/i2c-core-base.c:389
  really_probe+0x281/0x660 drivers/base/dd.c:509
  driver_probe_device+0x104/0x210 drivers/base/dd.c:670
  __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
  bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
  __device_attach+0x217/0x360 drivers/base/dd.c:843
  bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
  device_add+0xae6/0x16f0 drivers/base/core.c:2111
  i2c_new_client_device+0x5b3/0xc40 drivers/i2c/i2c-core-base.c:778
  i2c_new_device+0x19/0x50 drivers/i2c/i2c-core-base.c:821
  dvb_module_probe+0xf9/0x220 drivers/media/dvb-core/dvbdev.c:985
  friio_tuner_attach+0x125/0x1d0 drivers/media/usb/dvb-usb-v2/gl861.c:536
  dvb_usbv2_adapter_frontend_init
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:675 [inline]
  dvb_usbv2_adapter_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:804
[inline]
  dvb_usbv2_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:865 [inline]
  dvb_usbv2_probe.cold+0x24dc/0x255d
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:980
  usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
  really_probe+0x281/0x660 drivers/base/dd.c:509
  driver_probe_device+0x104/0x210 drivers/base/dd.c:670
  __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
  bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
  __device_attach+0x217/0x360 drivers/base/dd.c:843
  bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
  device_add+0xae6/0x16f0 drivers/base/core.c:2111
  usb_set_configuration+0xdf6/0x1670 drivers/usb/core/message.c:2023
  generic_probe+0x9d/0xd5 drivers/usb/core/generic.c:210
  usb_probe_device+0x99/0x100 drivers/usb/core/driver.c:266
  really_probe+0x281/0x660 drivers/base/dd.c:509
  driver_probe_device+0x104/0x210 drivers/base/dd.c:670
  __device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
  bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
  __device_attach+0x217/0x360 drivers/base/dd.c:843
  bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
  device_add+0xae6/0x16f0 drivers/base/core.c:2111
  usb_new_device.cold+0x8c1/0x1016 drivers/usb/core/hub.c:2534
  hub_port_connect drivers/usb/core/hub.c:5089 [inline]
  hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
  port_event drivers/usb/core/hub.c:5350 [inline]
  hub_event+0x1ada/0x3590 drivers/usb/core/hub.c:5432
  process_one_work+0x905/0x1570 kernel/workqueue.c:2269
  process_scheduled_works kernel/workqueue.c:2331 [inline]
  worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
  kthread+0x30b/0x410 kernel/kthread.c:255
  ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352

The buggy address belongs to the variable:
  id+0x100/0x120

Memory state around the buggy address:
  ffffffff89c9e480: fa fa fa fa 00 00 fa fa fa fa fa fa 00 00 00 00
  ffffffff89c9e500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> ffffffff89c9e580: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
                                                        ^
  ffffffff89c9e600: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
  ffffffff89c9e680: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
==================================================================

Reported-by: syzbot+8a8f48672560c8ca59dd@syzkaller.appspotmail.com
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 9fc3ce31f5bde660197f35135e90a1cced58aa2c ]

Fix and eliminate mceusb's IR length limit for IR signals transmitted to
the MCE IR blaster ports.

An IR signal TX exceeding 306 pulse/space samples presently causes -EINVAL
return error. There's no such limitation nor error with the MCE device
hardware. And valid IR signals exist with more than 400 pulse/space for the
control of certain appliances (eg Panasonic ACXA75C00600 air conditioner).

The scope of this patch is limited to the mceusb driver. There are still
IR signal TX length and time constraints that related modules of rc core
(eg LIRC) impose, further up the driver stack.

Changes for mceusb_tx_ir():

Converts and sends LIRC IR pulse/space sequence to MCE device IR
pulse/space format.

Break long length LIRC sequence into multiple (unlimited number of) parts
for sending to the MCE device.
Reduce kernel stack IR buffer size: 128 (was 384)
Increase MCE IR data packet size: 31 (was 5)
Zero time LIRC pulse/space no longer copied to MCE IR data.
Eliminate overwriting the source/input LIRC IR data in txbuf[].
Eliminate -EINVAL return; return number of IR samples sent (>0) or
MCE write error code (<0).

New mce_write() and mce_write_callback():

Implements synchronous blocking I/O, with timeout, for writing/sending
data to the MCE device.

An unlimited multipart IR signal sent to the MCE device faster than real
time requires flow control absent with the original mce_request_packet()
and mce_async_callback() asynchronous I/O implementation. Also absent is
TX error feedback.

mce_write() combines and replaces mce_request_packet() and
mce_async_callback() with conversion to synchronous I/O.
mce_write() returns bytes sent (>0) or MCE device write error (<0).
Debug hex dump TX data before processing.

Rename mce_async_out() -> mce_command_out():

The original name is misleading with underlying synchronous I/O
implementation. Function renamed to mce_command_out().

Changes in mceusb_handle_command():

Add support for MCE device error case MCE_RSP_TX_TIMEOUT
"IR TX timeout (TX buffer underrun)"

Changes in mceusb_dev_printdata():

Changes support test and debug of multipart TX IR.

Add buffer boundary information (offset and buffer size) to TX hex dump.
Correct TX trace bug "Raw IR data, 0 pulse/space samples"
Add trace for MCE_RSP_TX_TIMEOUT "IR TX timeout (TX buffer underrun)"

Other changes:

The driver's write to USB device architecture change (async to sync I/O)
is significant so we bump DRIVER_VERSION to "1.95" (from "1.94").

Tests:

$ cat -n irdata1 | head -3
     1  carrier 36000
     2  pulse 6350
     3  space 6350
$ cat -n irdata1 | tail -3
    76  pulse 6350
    77  space 6350
    78  pulse 6350
$ ir-ctl -s irdata1

[1549021.073612] mceusb 1-1.3:1.0: requesting 36000 HZ carrier
[1549021.073635] mceusb 1-1.3:1.0: tx data[0]: 9f 06 01 45 (len=4 sz=4)
[1549021.073649] mceusb 1-1.3:1.0: Request carrier of 35714 Hz (period 28us)
[1549021.073848] mceusb 1-1.3:1.0: tx done status = 4 (wait = 100, expire = 100 (1000ms), urb->actual_length = 4, urb->status = 0)
[1549021.074689] mceusb 1-1.3:1.0: rx data[0]: 9f 06 01 45 (len=4 sz=4)
[1549021.074701] mceusb 1-1.3:1.0: Got carrier of 35714 Hz (period 28us)
[1549021.102023] mceusb 1-1.3:1.0: tx data[0]: 9f 08 03 (len=3 sz=3)
[1549021.102036] mceusb 1-1.3:1.0: Request transmit blaster mask of 0x03
[1549021.102219] mceusb 1-1.3:1.0: tx done status = 3 (wait = 100, expire = 100 (1000ms), urb->actual_length = 3, urb->status = 0)
[1549021.131979] mceusb 1-1.3:1.0: tx data[0]: 9e ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f 9e ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f 91 ff (len=81 sz=81)
[1549021.131992] mceusb 1-1.3:1.0: Raw IR data, 30 pulse/space samples
[1549021.133592] mceusb 1-1.3:1.0: tx done status = 81 (wait = 100, expire = 100 (1000ms), urb->actual_length = 81, urb->status = 0)

Hex dumps limited to 64 bytes.
0xff is MCE maximum time pulse, 0x7f is MCE maximum time space.

$ cat -n irdata2 | head -3
     1  carrier 36000
     2  pulse 50
     3  space 50
$ cat -n irdata2 | tail -3
   254  pulse 50
   255  space 50
   256  pulse 50
$ ir-ctl -s irdata2

[1549306.586998] mceusb 1-1.3:1.0: tx data[0]: 9f 08 03 (len=3 sz=3)
[1549306.587015] mceusb 1-1.3:1.0: Request transmit blaster mask of 0x03
[1549306.587252] mceusb 1-1.3:1.0: tx done status = 3 (wait = 100, expire = 100 (1000ms), urb->actual_length = 3, urb->status = 0)
[1549306.613275] mceusb 1-1.3:1.0: tx data[0]: 9e 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 9e 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 9e 81 (len=128 sz=128)
[1549306.613291] mceusb 1-1.3:1.0: Raw IR data, 30 pulse/space samples
[1549306.614837] mceusb 1-1.3:1.0: tx done status = 128 (wait = 100, expire = 100 (1000ms), urb->actual_length = 128, urb->status = 0)
[1549306.614861] mceusb 1-1.3:1.0: tx data[0]: 9e 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 9e 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 9e 01 (len=128 sz=128)
[1549306.614869] mceusb 1-1.3:1.0: Raw IR data, 30 pulse/space samples
[1549306.620199] mceusb 1-1.3:1.0: tx done status = 128 (wait = 100, expire = 100 (1000ms), urb->actual_length = 128, urb->status = 0)
[1549306.620212] mceusb 1-1.3:1.0: tx data[0]: 89 81 01 81 01 81 01 81 01 81 80 (len=11 sz=11)
[1549306.620221] mceusb 1-1.3:1.0: Raw IR data, 9 pulse/space samples
[1549306.633294] mceusb 1-1.3:1.0: tx done status = 11 (wait = 98, expire = 100 (1000ms), urb->actual_length = 11, urb->status = 0)

Hex dumps limited to 64 bytes.
0x81 is MCE minimum time pulse, 0x01 is MCE minimum time space.
TX IR part 3 sz=11 shows 20msec I/O blocking delay
(100expire - 98wait = 2jiffies)
Signed-off-by: NA Sun <as1033x@comcast.net>
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab+samsung@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 887e975c4172d0d5670c39ead2f18ba1e4ec8133 ]

Fix bug added with the patch:

commit 8f3ea359
Author: Josef Bacik <josef@toxicpanda.com>
Date:   Mon Jul 16 12:11:35 2018 -0400

    nbd: handle unexpected replies better

where if the timeout handler runs when the completion path is and we fail
to grab the mutex in the timeout handler we will leave a config reference
and cannot free the config later.
Reviewed-by: NJosef Bacik <josef@toxicpanda.com>
Signed-off-by: NMike Christie <mchristi@redhat.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 60e2dde1e91ae0addb21ac380cc36ebee7534e49 ]

In led_trigger_set(), 'event' is allocated in kasprintf(). However, it is
not deallocated in the following execution if the label 'err_activate' or
'err_add_groups' is entered, leading to memory leaks. To fix this issue,
free 'event' before returning the error.

Fixes: 52c47742 ("leds: triggers: send uevent when changing triggers")
Signed-off-by: NWenwen Wang <wenwen@cs.uga.edu>
Acked-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJacek Anaszewski <jacek.anaszewski@gmail.com>
Signed-off-by: NSasha Levin <sashal@kernel.org>

[ Upstream commit 7df8f9a20196072162d9dc8fe99943f2d35f23d5 ]

The BCLK divider should be calculated using the parameters that actually
make the BCLK rate: the number of channels, the sampling rate and the
sample width.

We've been using the oversample_rate previously because in the former SoCs,
the BCLK's parent is MCLK, which in turn is being used to generate the
oversample rate, so we end up with something like this:

oversample = mclk_rate / sampling_rate
bclk_div = oversample / word_size / channels

So, bclk_div = mclk_rate / sampling_rate / word_size / channels.

And this is actually better, since the oversampling ratio only plays a role
because the MCLK is its parent, not because of what BCLK is supposed to be.

Furthermore, that assumption of MCLK being the parent has been broken on
newer SoCs, so let's use the proper formula, and have the parent rate as an
argument.

Fixes: 7d299381 ("ASoC: sun4i-i2s: Add support for H3")
Fixes: 21faaea1 ("ASoC: sun4i-i2s: Add support for A83T")
Fixes: 66ecce332538 ("ASoC: sun4i-i2s: Add compatibility with A64 codec I2S")
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://lore.kernel.org/r/c3595e3a9788c2ef2dcc30aa3c8c4953bb5cc249.1566242458.git-series.maxime.ripard@bootlin.comSigned-off-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NSasha Levin <sashal@kernel.org>