The various components accessing the bitrates table must use consider
the used channel bandwidth to select only available rates or calculate
the bitrate correctly.

There are some rates in reduced bandwidth modes which can't be
represented as multiples of 500kbps, like 2.25 MBit/s in 5 MHz mode. The
standard suggests to round up to the next multiple of 500kbps, just do
that in mac80211 as well.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
[make rate unsigned in ieee80211_add_tx_radiotap_header(), squash fix]
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

Wireshark already defines radiotap channel flags for 5 and 10 MHz, so
just use them in Linux radiotap too. Furthermore, add rx status flags to
allow drivers to report when they received data on 5 or 10 MHz channels.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

according to IEEE 802.11-2012 section 18, various timings change
when using 5 MHz and 10 MHz. Reflect this by using a "shift" when
calculating durations.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

5 and 10 MHz support needs to know the current operating channel width,
add the chandef to the rate control API.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

To allow scanning and working with 5 MHz and 10 MHz BSS, extend the
inform bss commands and add wrappers to take 5 and 10 MHz bss into
account.
Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

In most cases, host that receives IPv4 and IPv6 multicast/broadcast
packets does not do anything with these packets. Therefore the
reception of these unwanted packets causes unnecessary processing
and power consumption.

Packet coalesce feature helps to reduce number of received
interrupts to host by buffering these packets in firmware/hardware
for some predefined time. Received interrupt will be generated when
one of the following events occur.
a) Expiration of hardware timer whose expiration time is set to
maximum coalescing delay of matching coalesce rule.
b) Coalescing buffer in hardware reaches it's limit.
c) Packet doesn't match any of the configured coalesce rules.

This patch adds set/get configuration support for packet coalesce.
User needs to configure following parameters for creating a coalesce
rule.
a) Maximum coalescing delay
b) List of packet patterns which needs to be matched
c) Condition for coalescence. pattern 'match' or 'no match'
Multiple such rules can be created.

This feature needs to be advertised during driver initialization.
Drivers are supposed to do required firmware/hardware settings based
on user configuration.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
[fix kernel-doc, change free function, fix copy/paste error]
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

When per-chain signal information is available, don't add
the antenna field once but instead add a radiotap namespace
for each chain containing the chain/antenna number and the
signal strength on that chain.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

Signed-off-by: NSimon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: NMathias Kretschmer <mathias.kretschmer@fokus.fraunhofer.de>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

Currently packet patterns and it's enum/structures are used only
for WoWLAN feature. As we intend to reuse them for new feature
packet coalesce, they are renamed in this patch.

Older names are kept for backward compatibility purpose.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

... and use d_hash_and_lookup() instead of open-coding it, for fsck sake...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

just pass the name
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Static routes in this case are non-expiring routes which did not get
configured by autoconf or by icmpv6 redirects.

To make sure we actually get an ecmp route while searching for the first
one in this fib6_node's leafs, also make sure it matches the ecmp route
assumptions.

v2:
a) Removed RTF_EXPIRE check in dst.from chain. The check of RTF_ADDRCONF
   already ensures that this route, even if added again without
   RTF_EXPIRES (in case of a RA announcement with infinite timeout),
   does not cause the rt6i_nsiblings logic to go wrong if a later RA
   updates the expiration time later.

v3:
a) Allow RTF_EXPIRES routes to enter the ecmp route set. We have to do so,
   because an pmtu event could update the RTF_EXPIRES flag and we would
   not count this route, if another route joins this set. We now filter
   only for RTF_GATEWAY|RTF_ADDRCONF|RTF_DYNAMIC, which are flags that
   don't get changed after rt6_info construction.

Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change snmp RETRANSFAILS stat to include timeout retransmit failures
in addition to other loss recoveries.
Signed-off-by: NYuchung Cheng <ycheng@google.com>
Acked-by: NNeal Cardwell <ncardwell@google.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSunghan Suh <sunghan.suh@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

patch found using checkpatch.pl
Signed-off-by: NCosmin Stanescu <cosmin90stanescu@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of passing each byte by stack let's use nice specifier for that.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change fixes an MTU sizing issue seen with gretap tunnels when non-gso
packets are sent from the interface.

In my case I was able to reproduce the issue by simply sending a ping of
1421 bytes with the gretap interface created on a device with a standard
1500 mtu.

This fix is based on the fact that the tunnel mtu is already adjusted by
dev->hard_header_len so it would make sense that any packets being compared
against that mtu should also be adjusted by hard_header_len and the tunnel
header instead of just the tunnel header.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Reported-by: NCong Wang <amwang@redhat.com>
Acked-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the forward declaration of qfq_update_agg_ts, by moving
the definition of the function above its first call. This patch also
removes a useless forward declaration of qfq_schedule_agg.
Reported-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NPaolo Valente <paolo.valente@unimore.it>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In make_eligible, a mask is used to decide which groups must become eligible:
the i-th group becomes eligible only if the i-th bit of the mask (from the
right) is set. The mask is computed by left-shifting a 1 by a given number of
places, and decrementing the result.  The shift is performed on a ULL to avoid
problems in case the number of places to shift is higher than 31.  On a 32-bit
machine, this is more costly than working on an UL. This patch replaces such a
costly operation with two cheaper branches.

The trick is based on the following fact: in case of a shift of at least 32
places, the resulting mask has at least the 32 less significant bits set,
whereas the total number of groups is lower than 32.  As a consequence, in this
case it is enough to just set the 32 less significant bits of the mask with a
cheaper ~0UL. In the other case, the shift can be safely performed on a UL.
Reported-by: NDavid S. Miller <davem@davemloft.net>
Reported-by: NDavid Laight <David.Laight@ACULAB.COM>
Signed-off-by: NPaolo Valente <paolo.valente@unimore.it>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that the GRE and VXLAN tunnels can make use of Tx
checksum offload support provided by some drivers via the hw_enc_features.
Without this fix enabling GSO means sacrificing Tx checksum offload and
this actually leads to a performance regression as shown below:

            Utilization
            Send
Throughput  local         GSO
10^6bits/s  % S           state
  6276.51   8.39          enabled
  7123.52   8.42          disabled

To resolve this it was necessary to address two items.  First
netif_skb_features needed to be updated so that it would correctly handle
the Trans Ether Bridging protocol without impacting the need to check for
Q-in-Q tagging.  To do this it was necessary to update harmonize_features
so that it used skb_network_protocol instead of just using the outer
protocol.

Second it was necessary to update the GRE and UDP tunnel segmentation
offloads so that they would reset the encapsulation bit and inner header
offsets after the offload was complete.

As a result of this change I have seen the following results on a interface
with Tx checksum enabled for encapsulated frames:

            Utilization
            Send
Throughput  local         GSO
10^6bits/s  % S           state
  7123.52   8.42          disabled
  8321.75   5.43          enabled

v2: Instead of replacing refrence to skb->protocol with
    skb_network_protocol just replace the protocol reference in
    harmonize_features to allow for double VLAN tag checks.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Found using checkpatch.pl
Signed-off-by: NCamelia Groza <camelia.groza@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a follow-up patch to 3630d400
("ipv6: rt6_check_neigh should successfully verify neigh if no NUD
information are available").

Since the removal of rt->n in rt6_info we can end up with a dst ==
NULL in rt6_check_neigh. In case the kernel is not compiled with
CONFIG_IPV6_ROUTER_PREF we should also select a route with unkown
NUD state but we must not avoid doing round robin selection on routes
with the same target. So introduce and pass down a boolean ``do_rr'' to
indicate when we should update rt->rr_ptr. As soon as no route is valid
we do backtracking and do a lookup on a higher level in the fib trie.

v2:
a) Improved rt6_check_neigh logic (no need to create neighbour there)
   and documented return values.

v3:
a) Introduce enum rt6_nud_state to get rid of the magic numbers
   (thanks to David Miller).
b) Update and shorten commit message a bit to actualy reflect
   the source.
Reported-by: NPierre Emeriaud <petrus.lt@gmail.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

p9_release_pages() would attempt to dereference one value past the end of
pages[]. This would cause the following crashes:

[ 6293.171817] BUG: unable to handle kernel paging request at ffff8807c96f3000
[ 6293.174146] IP: [<ffffffff8412793b>] p9_release_pages+0x3b/0x60
[ 6293.176447] PGD 79c5067 PUD 82c1e3067 PMD 82c197067 PTE 80000007c96f3060
[ 6293.180060] Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
[ 6293.180060] Modules linked in:
[ 6293.180060] CPU: 62 PID: 174043 Comm: modprobe Tainted: G        W    3.10.0-next-20130710-sasha #3954
[ 6293.180060] task: ffff8807b803b000 ti: ffff880787dde000 task.ti: ffff880787dde000
[ 6293.180060] RIP: 0010:[<ffffffff8412793b>]  [<ffffffff8412793b>] p9_release_pages+0x3b/0x60
[ 6293.214316] RSP: 0000:ffff880787ddfc28  EFLAGS: 00010202
[ 6293.214316] RAX: 0000000000000001 RBX: ffff8807c96f2ff8 RCX: 0000000000000000
[ 6293.222017] RDX: ffff8807b803b000 RSI: 0000000000000001 RDI: ffffea001c7e3d40
[ 6293.222017] RBP: ffff880787ddfc48 R08: 0000000000000000 R09: 0000000000000000
[ 6293.222017] R10: 0000000000000001 R11: 0000000000000000 R12: 0000000000000001
[ 6293.222017] R13: 0000000000000001 R14: ffff8807cc50c070 R15: ffff8807cc50c070
[ 6293.222017] FS:  00007f572641d700(0000) GS:ffff8807f3600000(0000) knlGS:0000000000000000
[ 6293.256784] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[ 6293.256784] CR2: ffff8807c96f3000 CR3: 00000007c8e81000 CR4: 00000000000006e0
[ 6293.256784] Stack:
[ 6293.256784]  ffff880787ddfcc8 ffff880787ddfcc8 0000000000000000 ffff880787ddfcc8
[ 6293.256784]  ffff880787ddfd48 ffffffff84128be8 ffff880700000002 0000000000000001
[ 6293.256784]  ffff8807b803b000 ffff880787ddfce0 0000100000000000 0000000000000000
[ 6293.256784] Call Trace:
[ 6293.256784]  [<ffffffff84128be8>] p9_virtio_zc_request+0x598/0x630
[ 6293.256784]  [<ffffffff8115c610>] ? wake_up_bit+0x40/0x40
[ 6293.256784]  [<ffffffff841209b1>] p9_client_zc_rpc+0x111/0x3a0
[ 6293.256784]  [<ffffffff81174b78>] ? sched_clock_cpu+0x108/0x120
[ 6293.256784]  [<ffffffff84122a21>] p9_client_read+0xe1/0x2c0
[ 6293.256784]  [<ffffffff81708a90>] v9fs_file_read+0x90/0xc0
[ 6293.256784]  [<ffffffff812bd073>] vfs_read+0xc3/0x130
[ 6293.256784]  [<ffffffff811a78bd>] ? trace_hardirqs_on+0xd/0x10
[ 6293.256784]  [<ffffffff812bd5a2>] SyS_read+0x62/0xa0
[ 6293.256784]  [<ffffffff841a1a00>] tracesys+0xdd/0xe2
[ 6293.256784] Code: 66 90 48 89 fb 41 89 f5 48 8b 3f 48 85 ff 74 29 85 f6 74 25 45 31 e4 66 0f 1f 84 00 00 00 00 00 e8 eb 14 12 fd 41 ff c4 49 63 c4 <48> 8b 3c c3 48 85 ff 74 05 45 39 e5 75 e7 48 83 c4 08 5b 41 5c
[ 6293.256784] RIP  [<ffffffff8412793b>] p9_release_pages+0x3b/0x60
[ 6293.256784]  RSP <ffff880787ddfc28>
[ 6293.256784] CR2: ffff8807c96f3000
[ 6293.256784] ---[ end trace 50822ee72cd360fc ]---
Signed-off-by: NSasha Levin <sasha.levin@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We could end up expiring a route which is part of an ecmp route set. Doing
so would invalidate the rt->rt6i_nsiblings calculations and could provoke
the following panic:

[   80.144667] ------------[ cut here ]------------
[   80.145172] kernel BUG at net/ipv6/ip6_fib.c:733!
[   80.145172] invalid opcode: 0000 [#1] SMP
[   80.145172] Modules linked in: 8021q nf_conntrack_netbios_ns nf_conntrack_broadcast ipt_MASQUERADE ip6table_mangle ip6t_REJECT nf_conntrack_ipv6 nf_defrag_ipv6 iptable_nat nf_nat_ipv4 nf_nat iptable_mangle nf_conntrack_ipv4 nf_defrag_ipv4 xt_conntrack nf_conntrack ebtable_filter ebtables ip6table_filter ip6_tables
+snd_hda_intel snd_hda_codec snd_hwdep snd_seq snd_seq_device snd_pcm snd_page_alloc snd_timer virtio_balloon snd soundcore i2c_piix4 i2c_core virtio_net virtio_blk
[   80.145172] CPU: 1 PID: 786 Comm: ping6 Not tainted 3.10.0+ #118
[   80.145172] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
[   80.145172] task: ffff880117fa0000 ti: ffff880118770000 task.ti: ffff880118770000
[   80.145172] RIP: 0010:[<ffffffff815f3b5d>]  [<ffffffff815f3b5d>] fib6_add+0x75d/0x830
[   80.145172] RSP: 0018:ffff880118771798  EFLAGS: 00010202
[   80.145172] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffff88011350e480
[   80.145172] RDX: ffff88011350e238 RSI: 0000000000000004 RDI: ffff88011350f738
[   80.145172] RBP: ffff880118771848 R08: ffff880117903280 R09: 0000000000000001
[   80.145172] R10: 0000000000000000 R11: 0000000000000000 R12: ffff88011350f680
[   80.145172] R13: ffff880117903280 R14: ffff880118771890 R15: ffff88011350ef90
[   80.145172] FS:  00007f02b5127740(0000) GS:ffff88011fd00000(0000) knlGS:0000000000000000
[   80.145172] CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
[   80.145172] CR2: 00007f981322a000 CR3: 00000001181b1000 CR4: 00000000000006e0
[   80.145172] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[   80.145172] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
[   80.145172] Stack:
[   80.145172]  0000000000000001 ffff880100000000 ffff880100000000 ffff880117903280
[   80.145172]  0000000000000000 ffff880119a4cf00 0000000000000400 00000000000007fa
[   80.145172]  0000000000000000 0000000000000000 0000000000000000 ffff88011350f680
[   80.145172] Call Trace:
[   80.145172]  [<ffffffff815eeceb>] ? rt6_bind_peer+0x4b/0x90
[   80.145172]  [<ffffffff815ed985>] __ip6_ins_rt+0x45/0x70
[   80.145172]  [<ffffffff815eee35>] ip6_ins_rt+0x35/0x40
[   80.145172]  [<ffffffff815ef1e4>] ip6_pol_route.isra.44+0x3a4/0x4b0
[   80.145172]  [<ffffffff815ef34a>] ip6_pol_route_output+0x2a/0x30
[   80.145172]  [<ffffffff81616077>] fib6_rule_action+0xd7/0x210
[   80.145172]  [<ffffffff815ef320>] ? ip6_pol_route_input+0x30/0x30
[   80.145172]  [<ffffffff81553026>] fib_rules_lookup+0xc6/0x140
[   80.145172]  [<ffffffff81616374>] fib6_rule_lookup+0x44/0x80
[   80.145172]  [<ffffffff815ef320>] ? ip6_pol_route_input+0x30/0x30
[   80.145172]  [<ffffffff815edea3>] ip6_route_output+0x73/0xb0
[   80.145172]  [<ffffffff815dfdf3>] ip6_dst_lookup_tail+0x2c3/0x2e0
[   80.145172]  [<ffffffff813007b1>] ? list_del+0x11/0x40
[   80.145172]  [<ffffffff81082a4c>] ? remove_wait_queue+0x3c/0x50
[   80.145172]  [<ffffffff815dfe4d>] ip6_dst_lookup_flow+0x3d/0xa0
[   80.145172]  [<ffffffff815fda77>] rawv6_sendmsg+0x267/0xc20
[   80.145172]  [<ffffffff815a8a83>] inet_sendmsg+0x63/0xb0
[   80.145172]  [<ffffffff8128eb93>] ? selinux_socket_sendmsg+0x23/0x30
[   80.145172]  [<ffffffff815218d6>] sock_sendmsg+0xa6/0xd0
[   80.145172]  [<ffffffff81524a68>] SYSC_sendto+0x128/0x180
[   80.145172]  [<ffffffff8109825c>] ? update_curr+0xec/0x170
[   80.145172]  [<ffffffff81041d09>] ? kvm_clock_get_cycles+0x9/0x10
[   80.145172]  [<ffffffff810afd1e>] ? __getnstimeofday+0x3e/0xd0
[   80.145172]  [<ffffffff8152509e>] SyS_sendto+0xe/0x10
[   80.145172]  [<ffffffff8164efd9>] system_call_fastpath+0x16/0x1b
[   80.145172] Code: fe ff ff 41 f6 45 2a 06 0f 85 ca fe ff ff 49 8b 7e 08 4c 89 ee e8 94 ef ff ff e9 b9 fe ff ff 48 8b 82 28 05 00 00 e9 01 ff ff ff <0f> 0b 49 8b 54 24 30 0d 00 00 40 00 89 83 14 01 00 00 48 89 53
[   80.145172] RIP  [<ffffffff815f3b5d>] fib6_add+0x75d/0x830
[   80.145172]  RSP <ffff880118771798>
[   80.387413] ---[ end trace 02f20b7a8b81ed95 ]---
[   80.390154] Kernel panic - not syncing: Fatal exception in interrupt

Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename LL_SO to BUSY_POLL_SO
Rename sysctl_net_ll_{read,poll} to sysctl_busy_{read,poll}
Fix up users of these variables.
Fix documentation for sysctl.

a patch for the socket.7  man page will follow separately,
because of limitations of my mail setup.
Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename ndo_ll_poll to ndo_busy_poll.
Rename sk_mark_ll to sk_mark_napi_id.
Rename skb_mark_ll to skb_mark_napi_id.
Correct all useres of these functions.
Update comments and defines  in include/net/busy_poll.h
Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the file and correct all the places where it is included.
Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 38481605 (SUNRPC: fix races on
PipeFS MOUNT notifications) introduces a regression when we call
rpc_setup_pipedir() with RPCSEC_GSS as the auth flavour.

By calling rpcauth_create() while holding the sn->pipefs_sb_lock, we
end up deadlocking in gss_pipes_dentries_create_net().
Fix is to register the client and release the mutex before calling
rpcauth_create().
Reported-by: NWeston Andros Adamson <dros@netapp.com>
Tested-by: NWeston Andros Adamson <dros@netapp.com>
Cc: Stanislav Kinsbursky <skinsbursky@parallels.com>
Cc: <stable@vger.kernel.org> # : 38481605: SUNRPC: fix races on PipeFS MOUNT
Cc: <stable@vger.kernel.org> # : e73f4cc0: SUNRPC: split client creation
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Hi Jeff,

FYI, there are new sparse warnings show up in

tree:   git://git.linux-nfs.org/projects/trondmy/linux-nfs.git nfs-for-next
head:   296afe1f58d55fd56ed85daaafafcfee39f59ece
commit: 76fa6665 [2/5] rpc_pipe: set dentry operations at d_alloc time

>> net/sunrpc/rpc_pipe.c:496:31: sparse: symbol 'rpc_dir_inode_operations' was not declared. Should it be static?

Please consider folding the attached diff :-)
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Currently the way these get set is a little convoluted. If the dentry is
allocated via lookup from userland, then it gets set by simple_lookup.
If it gets allocated when the kernel is populating the directory, then
it gets set via __rpc_lookup_create_exclusive, which has to check
whether they might already be set. Between both of these, this ensures
that all dentries have their d_op pointer set.

Instead of doing that, just have them set at d_alloc time by pointing
sb->s_d_op at them. With that change, we no longer want the lookup op
to set them, so we must move to using our own lookup routine.
Signed-off-by: NJeff Layton <jlayton@redhat.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

This fix has been proposed originally by Vlad Yasevich. He says:

  When SCTP makes forward progress (receives a SACK that acks new chunks,
  renegs, or answeres 0-window probes) or when HB-ACK arrives, mark
  the route as confirmed so we don't unnecessarily send NUD probes.

Having a simple SCTP client/server that exchange data chunks every 1sec,
without this patch ARP requests are sent periodically every 40-60sec.
With this fix applied, an ARP request is only done once right at the
"session" beginning. Also, when clearing the related ARP cache entry
manually during the session, a new request is correctly done. I have
only "backported" this to net-next and tested that it works, so full
credit goes to Vlad.
Signed-off-by: NVlad Yasevich <vyasevich@gmail.com>
Signed-off-by: NDaniel Borkmann <dborkman@redhat.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename functions in include/net/ll_poll.h to busy wait.
Clarify documentation about expected power use increase.
Rename POLL_LL to POLL_BUSY_LOOP.
Add need_resched() testing to poll/select busy loops.

Note, that in select and poll can_busy_poll is dynamic and is
updated continuously to reflect the existence of supported
sockets with valid queue information.
Signed-off-by: NEliezer Tamir <eliezer.tamir@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As of f025adf1 "sunrpc: Properly decode
kuids and kgids in RPC_AUTH_UNIX credentials" any rpc containing a -1
(0xffff) uid or gid would fail with a badcred error.

Commit afe3c3fd "svcrpc: fix failures to
handle -1 uid's and gid's" fixed part of the problem, but overlooked the
gid upcall--the kernel can request supplementary gid's for the -1 uid,
but mountd's attempt write a response will get -EINVAL.

Symptoms were nfsd failing to reply to the first attempt to use a newly
negotiated krb5 context.
Reported-by: NSven Geggus <lists@fuchsschwanzdomain.de>
Tested-by: NSven Geggus <lists@fuchsschwanzdomain.de>
Cc: stable@vger.kernel.org
Signed-off-by: NJ. Bruce Fields <bfields@redhat.com>

RDMA needs to post a buffer for each incoming reply.
Hence it needs to keep count of these and needs to be
aware of whether a flushed request has received a reply
or not.

This patch adds the cancelled() callback to the transport modules.
It is called when RFLUSH has been received and that the corresponding
request will never receive a reply.
Signed-off-by: NSimon Derr <simon.derr@bull.net>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

In rdma_request():

If an error occurs between posting the recv and the send,
there will be a reply context posted without a pending
request.
Since there is no way to "un-post" it, we remember it and
skip post_recv() for the next request.
Signed-off-by: NSimon Derr <simon.derr@bull.net>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

Most importantly:
- do not free the recv context (rpl_context) after a successful post_recv()
- but do free the send context (c) after a failed send.
Signed-off-by: NSimon Derr <simon.derr@bull.net>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

rdma_request() should never be in charge of freeing rc.

When an error occurs:
* Either the rc buffer has been recv_post()'ed.
  then kfree()'ing it certainly is a bad idea.
* Or is has not, and in that case req->rc still points to it,
  hence it needs not be freed.
Signed-off-by: NSimon Derr <simon.derr@bull.net>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>

The current code keeps track of the number of buffers posted in the RQ,
and will prevent it from overflowing. But it does so by simply dropping
post requests (And leaking memory in the process).
When this happens there will actually be too few buffers posted, and
soon the 9P server will complain about 'RNR retry counter exceeded'
errors.

Instead, use a semaphore, and block until the RQ is ready for another
buffer to be posted.
Signed-off-by: NSimon Derr <simon.derr@bull.net>
Signed-off-by: NEric Van Hensbergen <ericvh@gmail.com>