There is no point in having a S390 private implementation and there is
no point in using the raw monotonic time. The NTP freqeuency
adjustment of CLOCK_MONOTONIC is really not doing any harm for the
hang check timer.

Use ktime_get_ns() for everything and get rid of the timespec
conversions.

V2: Drop the raw monotonic and the S390 special case
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Using the wall clock time for delta time calculations is wrong to
begin with because wall clock time can be set from userspace and NTP.
Such data wants to be based on clock monotonic.

The calculations also are done on a nanosecond basis. Use the
nanoseconds based interface right away.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <jdelvare@suse.de>
Acked-by: NJean Delvare <jdelvare@suse.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

This code is beyond silly:

     struct timespec ts = ktime_get_ts();
     ktime_t ktime = timespec_to_ktime(ts);

Further down the code builds the delta of two ktime_t values and
converts the result to nanoseconds.

Use ktime_get_ns() and replace all the nonsense.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Eli Cohen <eli@mellanox.com>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Replace the ever recurring:
        ts = ktime_get_ts();
        ns = timespec_to_ns(&ts);
with
        ns = ktime_get_ns();
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Replace the ever recurring:
	ts = ktime_get_ts();
	ns = timespec_to_ns(&ts);
with
	ns = ktime_get_ns();
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Replace the ever recurring:
        ts = ktime_get_ts();
        ns = timespec_to_ns(&ts);
with
        ns = ktime_get_ns();
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Convert the monotonic timestamp with ktime_mono_to_real() in
drm_calc_vbltimestamp_from_scanoutpos().

In get_drm_timestamp we can call either ktime_get() or
ktime_get_real() depending on drm_timestamp_monotonic. No point in
having two calls into the core for CLOCK_REALTIME.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

Convert the monotonic timestamp with ktime_mono_to_real() in
evdev_events().

In evdev_queue_syn_dropped() we can call either ktime_get() or
ktime_get_real() depending on the clkid. No point in having two calls
for CLOCK_REALTIME.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>

The MCT has a nice 64-bit counter.  That means that we _can_ register
as a 64-bit clocksource and sched_clock.  ...but that doesn't mean we
should.

The 64-bit counter is read by reading two 32-bit registers.  That
means reading needs to be something like:
- Read upper half
- Read lower half
- Read upper half and confirm that it hasn't changed.

That wouldn't be terrible, but:
- THe MCT isn't very fast to access (hundreds of nanoseconds).
- The clocksource is queried _all the time_.

In total system profiles of real workloads on ChromeOS, we've seen
exynos_frc_read() taking 2% or more of CPU time even after optimizing
the 3 reads above to 2 (see below).

The MCT is clocked at ~24MHz on all known systems.  That means that
the 32-bit half of the counter rolls over every ~178 seconds.  This
inspired an optimization in ChromeOS to cache the upper half between
calls, moving 3 reads to 2.  ...but we can do better!  Having a 32-bit
timer that flips every 178 seconds is more than sufficient for Linux.
Let's just use the lower half of the MCT.

Times on 5420 to do 1000000 gettimeofday() calls from userspace:
* Original code:                      1323852 us
* ChromeOS cache upper half:          1173084 us
* ChromeOS + ldmia to optimize:       1045674 us
* Use lower 32-bit only (this code):  1014429 us

As you can see, the time used doesn't increase linearly with the
number of reads and we can make 64-bit work almost as fast as 32-bit
with a bit of assembly code.  But since there's no real gain for
64-bit, let's go with the simplest and fastest implementation.

Note: with this change roughly half the time for gettimeofday() is
spent in exynos_frc_read().  The rest is timer / system call overhead.

Also note: this patch disables the use of the MCT on ARM64 systems
until we've sorted out how to make "cycles_t" always 32-bit.  Really
ARM64 systems should be using arch timers anyway.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Acked-by Vincent Guittot <vincent.guittot@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

Using the __raw functions is discouraged.  Update the file to
consistently use the proper functions.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

Add device-tree support to PXA platforms.
The driver still needs to maintain backward non device-tree
compatibility as well, which implies :
 - a non device-tree init function
 - a static registers base address in the driver
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

Move time.c from arch/arm/mach-pxa/time.c to
drivers/clocksource/pxa_timer.c.
Signed-off-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

This adds the clocksource driver for Cirrus Logic CLPS711X series SoCs.
Designed primarily for migration CLPS711X subarch for multiplatform & DT,
for this as the "OF" and "non-OF" calls implemented.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

In the clocksource driver, we didn't explicitly enable the clock. it makes the
clk reference counter wrong. We didn't encounter any hang issue because the
tick's clock input has been open and is shared by some other hardware
components, but if we don't enable those components in kernel, in the stage of
disabling unused clk in kernel boot, Linux tick hangs.

This patch fixes it. it does an explicit prepare and enable to the clock input,
and increases the usage counter of the clk.
Signed-off-by: NZhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

In 'em_sti.c', it will call devm_ioremap_resource() which need
HAS_IOMEM. So need let EM_TIMER_STI depend on HAS_IOMEM, too.

The related error (with allmodconfig under score):

  LD      init/built-in.o
em_sti.c:(.text.em_sti_probe+0x84): undefined reference to `devm_ioremap_resource'
make: *** [vmlinux] Error 1
Signed-off-by: NChen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

This patch adds a clock source and clock event for the timer found
on the Mediatek SoCs.

The Mediatek General Purpose Timer block provides five 32 bit timers and
one 64 bit timer.

Two 32 bit timers are used by this driver:
TIMER1: clock events supporting periodic and oneshot events
TIMER2: clock source configured as a free running counter

The General Purpose Timer block can be run with two clocks. A 13 MHz system
clock and the RTC clock running at 32 KHz. This implementation uses the system
clock with no clock source divider.

The interrupts are shared between the different timers and have to be read back
from a register. We just enable one interrupt for the clock event. The clock
event timer is used by all cores.
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

A call to of_iomap does not request the memory region. This patch adds the
function of_io_request_and_map which requests the memory region before
mapping it.
Signed-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Suggested-by: NThomas Gleixner <tglx@linutronix.de>
Suggested-by: NRob Herring <robh@kernel.org>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

It should be "MTU2" instead of "TMU2"
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NDaniel Lezcano <daniel.lezcano@linaro.org>

The uarts only work when the parent is ras_ahb_clk. The stale 3.5
based ST tree does this in the board file.

Add it to the clk init function. Not pretty, but the mess there is
amazing anyway.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The control register is at offset 0x10, not 0x0. This is wreckaged
since commit 5df33a62 (SPEAr: Switch to common clock framework).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

If probe fails then we need to call pm_runtime_disable() to balance
out the previous pm_runtime_enable() call. Else it will cause
unbalanced pm_runtime_enable() call in the succeding probe call.

This anomaly was observed when the call to devm_phy_create() failed
with -EPROBE_DEFER.

Balance out the pm_runtime_enable() call in .remove() as well.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Prevent resources from being freed twice in case device_add() call
fails within phy_create(). Also use ida_simple_remove() instead of
ida_remove() as we had used ida_simple_get() to allocate the ida.

Cc: 3.13+ <stable@vger.kernel.org> # 3.13+
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allow phy-exynos-usb2 to be autoloaded based on devicetree information.
Tested on Odroid X2 with its USB subsystem build as modules.
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

devm_ioremap_resource returns an ERR_PTR value, not NULL, on failure.

A simplified version of the semantic match that finds this problem is as
follows:

// <smpl>
@@
expression e,e1;
statement S;
@@

*e = devm_ioremap_resource(...);
if (!e1) S

// </smpl>
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver depend on the reset framework in a mandatory way. Make sure
reset_control_get is defined by adding this dependency in Kconfig
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds support for Infineon TriBoard TC1798 [1]. Only interface 1
is used as serial line (see [2], Figure 8-6).

[1] http://www.infineon.com/cms/de/product/microcontroller/development-tools-software-and-kits/tricore-tm-development-tools-software-and-kits/starterkits-and-evaluation-boards/starter-kit-tc1798/channel.html?channel=db3a304333b8a7ca0133cfa3d73e4268
[2] http://www.infineon.com/dgdl/TriBoardManual-TC1798-V10.pdf?folderId=db3a304412b407950112b409ae7c0343&fileId=db3a304333b8a7ca0133cfae99fe426aSigned-off-by: NMichal Sojka <sojkam1@fel.cvut.cz>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix breakage introduced by
commit c557d392,
'serial: Test for no tx data on tx restart'.
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replace open-coded test for empty tx ring buffer with equivalent
helper function, uart_circ_empty(). No functional change.
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 717f3bba,
'serial_core: Fix conditional start_tx on ring buffer not empty'
exposes an incorrect assumption in several drivers' start_tx methods;
the tx ring buffer can, in fact, be empty when restarting tx while
performing flow control.

Affected drivers:
sunsab.c
ip22zilog.c
pmac_zilog.c
sunzilog.c
m32r_sio.c
imx.c

Other in-tree serial drivers either are not affected or already
test for empty tx ring buffer before transmitting.

Test for empty tx ring buffer in start_tx() method, after transmitting
x_char (if applicable).
Reported-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: Seth Bollinger <sethb@digi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Cc: stable <stable@vger.kernel.org> # 3.15
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Adds IDs for MUX clocks to be used by power domain for MFC
for doing re-parenting while pd on/off.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NShaik Ameer Basha <shaik.ameer@samsung.com>
Acked-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

It reverts commit c745fe61 now that
Cayman is stable since VDDCI fix. Spread spectrum was not the culprit.

This depends on b0880e87
(drm/radeon/dpm: fix vddci setup typo on cayman).
Signed-off-by: NAlexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Need to use the RREG32_SMC() accessor since the register
is an smc indirect index.
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Fixes hangs on driver load on some cards.

bug:
https://bugs.freedesktop.org/show_bug.cgi?id=76998Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Signed-off-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

If there are error flags in the aux transaction return
-EIO rather than -EBUSY.  -EIO restarts the whole transaction
while -EBUSY jus retries.  Fixes problematic aux transfers.

Bug:
https://bugs.freedesktop.org/show_bug.cgi?id=80684Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Commit e8099177 ("dm mpath: push back requests instead of queueing")
modified multipath_busy() to return true if !pg_ready().  pg_ready()
checks the current state of the multipath device and may return false
even if a new IO is needed to change the state.

Bart Van Assche reported that he had multipath IO lockup when he was
performing cable pull tests.  Analysis showed that the multipath
device had a single path group with both paths active, but that the
path group itself was not active.  During the multipath device state
transitions 'queue_io' got set but nothing could clear it.  Clearing
'queue_io' only happens in __choose_pgpath(), but it won't be called
if multipath_busy() returns true due to pg_ready() returning false
when 'queue_io' is set.

As such the !pg_ready() check in multipath_busy() is wrong because new
IO will not be sent to multipath target and the multipath state change
won't happen.  That results in multipath IO lockup.

The intent of multipath_busy() is to avoid unnecessary cycles of
dequeue + request_fn + requeue if it is known that the multipath
device will requeue.

Such "busy" situations would be:
  - path group is being activated
  - there is no path and the multipath is setup to requeue if no path

Fix multipath_busy() to return "busy" early only for these specific
situations.
Reported-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.15

There's a race condition between the atomic_dec_and_test(&io->count)
in dec_count() and the waking of the sync_io() thread.  If the thread
is spuriously woken immediately after the decrement it may exit,
making the on stack io struct invalid, yet the dec_count could still
be using it.

Fix this race by using a completion in sync_io() and dec_count().
Reported-by: NMinfei Huang <huangminfei@ucloud.cn>
Signed-off-by: NJoe Thornber <thornber@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Acked-by: NMikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org

Signed-off-by: NJana Saout <jana@saout.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

The commit 2c140a24 ("dm: allow remove to be deferred") introduced a
deferred removal feature for the device mapper.  When this feature is
used (by passing a flag DM_DEFERRED_REMOVE to DM_DEV_REMOVE_CMD ioctl)
and the user tries to remove a device that is currently in use, the
device will be removed automatically in the future when the last user
closes it.

Device mapper used the system workqueue to perform deferred removals.
However, some targets (dm-raid1, dm-mpath, dm-stripe) flush work items
scheduled for the system workqueue from their destructor.  If the
destructor itself is called from the system workqueue during deferred
removal, it introduces a possible deadlock - the workqueue tries to flush
itself.

Fix this possible deadlock by introducing a new workqueue for deferred
removals.  We allocate just one workqueue for all dm targets.  The
ability of dm targets to process IOs isn't dependent on deferred removal
of unused targets, so a deadlock due to shared workqueue isn't possible.

Also, cleanup local_init() to eliminate potential for returning success
on failure.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.13+

This patch fixes a memory leak that appears when caam_jr module is unloaded.

Cc: <stable@vger.kernel.org> # 3.13+
Signed-off-by: NCristian Stoica <cristian.stoica@freescale.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>