- 23 10月, 2010 1 次提交
-
-
由 Laurent Pinchart 提交于
With the v4l2_i2c_new_subdev* functions now supporting loading modules based on modaliases, remove the module names hardcoded in platform data and pass a NULL module name to those functions. All corresponding I2C modules have been checked, and all of them include a module aliases table with names corresponding to what the soc_camera platform data uses. Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>
-
- 11 8月, 2010 1 次提交
-
-
由 Igor Grinberg 提交于
1) Introduce ulpi specific flags for control of the ulpi phy 2) Extend the generic ulpi driver with support for Function and Interface control of upli phy 3) Update the platforms using the generic ulpi driver with new ulpi flags 4) Remove the otg control flags not in use Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il> Signed-off-by: NMike Rapoport <mike@compulab.co.il> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 30 6月, 2010 2 次提交
-
-
由 Uwe Kleine-König 提交于
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
-
由 Uwe Kleine-König 提交于
As the kernel contains a copy of the GPL anyhow just get rid of the address specification instead of fixing it. Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
-
- 17 5月, 2010 2 次提交
-
-
由 Philippe Rétornaz 提交于
The Eyebot robot needs the OTG port in host mode on the smartbot. Add a new board definition so we can select the usb host/device mode at boot with the mx31moboard_baseboard boot parameter. Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
由 Philippe Rétornaz 提交于
In preparation for a new robot which needs the OTG port as host. This moves the OTG device registration into board initialisation. Signed-off-by: NPhilippe Rétornaz <philippe.retornaz@epfl.ch> Acked-by: NValentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 06 5月, 2010 1 次提交
-
-
由 Valentin Longchamp 提交于
Since it is finally used on the handbot as a configuration input for the translator. Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-
- 10 2月, 2010 1 次提交
-
-
由 Valentin Longchamp 提交于
This baseboard is used on the handbot and eybot robots. The sel gpios are used as enables and rst signals on smartbot, thus the sel init is moved from mx31moboard file to board files. Signed-off-by: NValentin Longchamp <valentin.longchamp@epfl.ch> Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
-