Remove some obsolete comments, and bump up the driver version number.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This driver currently has no need for the .post_internal_cmd op.
So get rid of it, to save unnecessary transitions between EDMA and non-EDMA modes.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Final changes to actually turn on NCQ in the driver for GEN_II/IIE hardware.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In preparation for supporting NCQ, we must allocate separate SG tables
for each command tag, rather than just a single table per port as before.

Gen-I hardware cannot do NCQ, though, so we still allocate just a single
table for that, but populate it in all 32 slots to avoid special-cases
elsewhere in hotter paths of the code.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds the Intel ICH10 IDE mode SATA Controller DeviceID's.
Signed-off-by: NJason Gaston <jason.d.gaston@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds the Intel ICH10 SATA RAID Controllers DeviceID's.
Signed-off-by: NJason Gaston <jason.d.gaston@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Create host-owned DMA memory pools, for use in allocating/freeing per-port
command/response queues and SG tables.  This gives us a way to guarantee we
meet the hardware address alignment requirements, and also reduces memory that
might otherwise be wasted on alignment gaps.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The GenII chips have only 8-bits for the sector_count field when performing NCQ.
Add a dev_config method to restrict this when necessary, taking care not to
override any other restriction already in place (likely none, but someday.. ?).
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The lower 8 bits of response status are not valid for NCQ.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Simplify tag handling by using the cid/hqtag field instead of ioid,
as recommended by Marvell.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

An extra EDMA config bit is required for NCQ operation.
So set/clear it as needed, and cache current setting in port_priv.
For now though, it will always be "off" (0).
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Simplify and fix EDMA configuration setup to match Marvell specificiations.
The chip documentation gives a specific (re)init sequence, which we now follow.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use naming consistent with elsewhere in this driver.
This will keep things less confusing when we later add "hc_mmio" in this function.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The chips can handle many transient errors internally without a software IRQ.
We now mask/ignore those interrupts here.  This is necessary for NCQ, later on.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A hard reset is necessary after hotplug events.
Only clear the error irq bits that were set on entry.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use container_of() instead of assuming local uart struct is first member
of uart_port struct.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use IRQF_DISABLED instead of obsolete IRQ_FLG_STD for request_irq() flags
in m68328serial.c driver.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add configure support for new ColdFire serial driver.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add build support for new ColdFire serial driver.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The MSSR constants didn't match the reality - bitfield declarations used
to be correct (1000BT_FD - bit 11, 1000BT_HD - bit 10), but enum had
them the other way round.  Went unnoticed until the switch from the
bitfields use to the explicit arithmetics and I hadn't caught that one
when verifying correctness of change...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

It's perfectly legal to have data leftovers when a drive signals
completion, it happens all the time when a user issues a command
with a transfer count that is too large.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch removes the no longer used EXPORT_SYMBOL(add_disk_randomness).
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NMatt Mackall <mpm@selenic.com>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

This patch fixes the following section mismatches:

<--  snip  -->

...
WARNING: drivers/block/sunvdc.o(.text+0xf0): Section mismatch in reference from the function print_version() to the variable .devinit.data:version
WARNING: drivers/block/sunvdc.o(.text+0xf8): Section mismatch in reference from the function print_version() to the variable .devinit.data:version
...

<--  snip  -->
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

We were checking for the ASYM_PAUSE bit for 1000Base-X twice instead
checking for both the 1000Base-X bit and the 10/100/1000Base-T bit.
The purpose of the logic is to tell the firmware that ASYM_PAUSE is
set on either the Serdes or Copper interface.

Problem was discovered by Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In drivers/net/macvlan.c, when rtnl_link_register() fails in
macvlan_init_module(), there is no point to set it (second time in
this method) to macvlan_handle_frame; macvlan_init_module() will
return a negative number, so instead this patch sets
macvlan_handle_frame_hook to NULL.
Signed-off-by: NRami Rosen <ramirose@gmail.com>
Acked-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update firmware to support programmable flow control.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make use of the programmable high/low water marks in 5709 for
802.3 flow control.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CTX_WR macro is unnecessary and obfuscates the code.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The REG_WR_IND/REG_RD_IND macros are unnecessary and obfuscate the
code.  Many callers to these macros read and write shared memory from
the bp->shmem_base, so we add 2 similar functions that automatically
add the shared memory base.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the tx coalescing setup code independent of the MSIX vector.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Correct the MII expansion serdes control register definition.
2. Check an additional RUDI_INVALID bit when determining 5706S link.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New driver for wireless RNDIS devices. So far only known chip that uses
wireless RNDIS is Broadcom 4320. Driver detects all RNDIS devices that
have RNDIS wireless physical medium. At least following devices are
detected:

  Buffalo WLI-U2-KG125S
  U.S. Robotics USR5421
  Belkin F5D7051
  Linksys WUSB54GSv2
  Linksys WUSB54GSC
  Asus WL169gE
  Eminent EM4045
  BT Voyager 1055
  Linksys WUSB54GSv1
  U.S. Robotics USR5420
  BUFFALO WLI-USB-G54
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move headers usbnet.h and rndis_host.h to include/linux/usb and fix includes
for drivers/net/usb modules. Headers are moved because rndis_wlan will be
outside drivers/net/usb in drivers/net/wireless and yet need these headers.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add RNDIS physical medium checking into generic_rndis_bind() and also make
rndis_host to be only bind on every medium except wireless.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Callback to signal link state changes from minidriver to
'subminidrivers'.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function pointer is for 'subminidrivers' that need to do work on device
right after minidriver has initialized hardware.

For example, rndis_wlan setting device specific configuration parameters
with OID_GEN_RNDIS_CONFIG_PARAMETER right after rndis_host has
initialized hardware with RNDIS_INIT.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a private data pointer to usbnet for rndis_wlan module to use.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Export rndis_host functions and also rename rndis_bind() to
generic_rndis_bind() for modules using rndis_host as base.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Split up rndis_host.c into rndis_host.h and rndis_base.c. This is done so
that rndis_wlan can reuse common parts with rndis_host.
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>