- 14 3月, 2015 1 次提交
-
-
由 Don Skidmore 提交于
For the X550 mac type we have to do additional steps around enabling/disabling Rx. This patch will add a layer of indirection around these support functions to enable this. CC: <kernel-team@fb.com> Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 06 12月, 2014 4 次提交
-
-
由 Don Skidmore 提交于
This patch extends the function pointer structure to include the new X550 class MAC types. This creates a new file ixgbe_x550.c that contains all of the new methods. Because of similarities to the X540 part in some cases we just use it's methods where they can be used without any modification. These exported functions are now defined in the new ixgbe_x540.h file. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Don Skidmore 提交于
Currently the shared code checksum calculation function only returns a u16 and cannot return an error code. Unfortunately a variety of errors can happen that completely prevent the calculation of a checksum. So, change the function return value from a u16 to an s32 and return a negative value on error, or the positive checksum value when there is no error. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Don Skidmore 提交于
The X550 hardware will use more bits in the mask, so change the prototypes to match. This larger mask will require changes in callers which use the higher bits. Likewise since X550 will use different semaphore mask values and will use the lan_id value. So save these values in the ixgbe_phy_info struct. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Don Skidmore 提交于
Since on X550 we use host interface commands to read,write and erase some commands require more time to complete. So this adds a timeout parameter to ixgbe_host_interface_command as wells as a return_data parameter allowing us to return with any data. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 11 11月, 2014 2 次提交
-
-
由 Don Skidmore 提交于
This patch will add in the new MAC defines and fit it into the switch cases throughout the driver. New functionality and enablement support will be added in following patches. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Don Skidmore 提交于
On topologies including few levels of PCIe switching X540 can run into an unexpected completion error. We get around this by waiting after enabling loopback a sufficient amount of time until Tx Data Fetch is sent. We then poll the pending transaction bit to ensure we received the completion. Only then do we go on to clear the buffers. Signed-of-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 26 7月, 2014 2 次提交
-
-
由 Mark Rustad 提交于
Make return values more direct, eliminating some gotos and otherwise unneeded conditionals. This also eliminates some local variables. Also a few minor cleanups in affected code so checkpatch won't complain. Signed-off-by: NMark Rustad <mark.d.rustad@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Mark Rustad 提交于
Convert some udelay calls to the preferred usleep_range. Signed-off-by: NMark Rustad <mark.d.rustad@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 14 7月, 2014 1 次提交
-
-
由 Fabian Frederick 提交于
Signed-off-by: NFabian Frederick <fabf@skynet.be> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 5月, 2014 3 次提交
-
-
由 Jacob Keller 提交于
This commit fixes a checkpatch.pl warning for style, by adding braces around the else block, since the if block requires braces. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
This patch fixes various log strings that are split over multiple lines in the ixgbe driver. This cleans up checkpatch.pl warnings, and makes it easier to search the code for warning strings displayed to the kernel log. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
The contents of this patch were originally generated by "scripts/checkpatch.pl --fix-inplace --types CODE_INDENT,LEADING_SPACE drivers/net/ethernet/ixgbe/*.[ch]", and then hand verified for consistency. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 23 4月, 2014 1 次提交
-
-
由 Jacob Keller 提交于
Since fc.high_water is an array, we should treat low_water as an array also. This allows the algorithm to output different values for different TCs, and then we can distinguish between them. In addition, this patch changes one path that didn't honor the return value from ixgbe_setup_fc. Reported-by: NAaron Salter <aaron.k.salter@intel.com> Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 19 4月, 2014 1 次提交
-
-
由 Jakub Kicinski 提交于
Add \n at the end of messages where missing, remove all \r. Reported-by: NJoe Perches <joe@perches.com> Signed-off-by: NJakub Kicinski <kubakici@wp.pl> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Tested-by: NKavindya Deegala <kavindya.s.deegala@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 21 3月, 2014 1 次提交
-
-
由 Mark Rustad 提交于
When an adapter is removed and registers all read as all one's, an infinite recursion can happen between ixgbe_clear_vmdq_generic and ixgbe_clear_rar_generic. Adding a check for removal breaks this recursion. Signed-off-by: NMark Rustad <mark.d.rustad@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 20 3月, 2014 3 次提交
-
-
由 Jacob Keller 提交于
This patch replaces some direct uses of pci_read_config_word with the protected ixgbe_read_pci_cfg_word function, which checks for whether the adapter is removed when LER is enabled. We shouldn't use the pci_read_config_word calls directly because of these checks. This patch also cleans up an unnecessary save of a pointer to the mac object, as our standard style is to just use the hw pointer. CC: Arun Sharma <asharma@fb.com> Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
This patch reverts the addition of the fiber_fixed type, which ended up never being used. We don't have plans to support this type going forward, and there is no reason to keep an unused type around polluting the code. Reverts: 4e8e1bca ("ixgbe: add new media type") CC: Arun Sharma <asharma@fb.com> Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Don Skidmore 提交于
Found several incorrect conditionals after calling the prot_autoc_* functions. Likewise we weren't always freeing the FWSW semaphore after grabbing it. This would lead to DA cables being unable to link along with possible other errors. CC: Arun Sharma <asharma@fb.com> CC: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 13 3月, 2014 1 次提交
-
-
由 Jacob Keller 提交于
This patch updates the contact information on the ixgbe driver files so that every file includes the Linux NICS address, as it is still used, but only a few of the files mentioned it. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 03 3月, 2014 1 次提交
-
-
由 Mark Rustad 提交于
Configuration space reads should also be checked for removal. So add some checks related to config space accesses. v2: * Fixed indent Signed-off-by: NMark Rustad <mark.d.rustad@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 01 3月, 2014 2 次提交
-
-
由 Don Skidmore 提交于
When reading or writing to the AUTOC register on 82599 devices we need to preform various operations that aren't needed for other MAC types. This patch will collect all of that code into one place to minimize MAC checks in common code paths. While doing this I also clean up some cases where we weren't holding the SW/FW semaphore during a read/modify/write of AUTOC. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Don Skidmore 提交于
Currently we were just always polling for a hard coded 80 ms and not respecting the system-wide timeout interval. Since up until now all devices have been tested with this 80ms value we continue to use this value as a hard minimum. Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 8月, 2013 1 次提交
-
-
由 Mark Rustad 提交于
This patch fixes the possible use of uninitialized memory by checking the return value on eeprom reads. These issues were identified by static analysis. In many cases error messages will be produced so that corrupted eeprom issues will be more visible. Signed-off-by: NMark Rustad <mark.d.rustad@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 31 7月, 2013 3 次提交
-
-
由 Emil Tantilov 提交于
This patch changes the error code path in ixgbe_acquire_swfw_sync() to deal with cases where acquiring SW semaphore times out. In cases where the SW/FW semaphore bits were set (i.e. due to a crash) the driver will hang on load. With this patch the driver will clear the stuck bits if the semaphore was not acquired in the allotted time. Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Don Skidmore 提交于
This patch adds support for a new media type fiber_fixed. This is useful to avoid all the SFP+ hot plug support path on devices who's fix fiber need not worry about such things. This patch is needed for a following patch that adds support for "fiber_fixed" devices. v2: cleaned up logging message based on feedback from David Miller Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Don Skidmore 提交于
Originally ixgbe_device_supports_autoneg_fc() was only expected to be called by copper devices. This would lead to false information to be displayed via ethtool. v2: changed ixgbe_device_supports_autoneg_fc() to a bool function, it returns bool. Based on feedback from David Miller Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 18 4月, 2013 3 次提交
-
-
由 Jacob Keller 提交于
This patch cleans up ixgbe_get_bus_info_generic to call some conversion functions, which are used also in a follow on patch that needs to convert between the link_status PCIe config values into ixgbe's internal enum representations. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Jacob Keller 提交于
This patch adds support for displaying PCIe Gen3 link speed, which was previously missing from the driver. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Emil Tantilov 提交于
Make the calculation of eerd consistent between the read and write functions by using | instead of + for IXGBE_EEPROM_RW_REG_START Reported-by: NDan Carpenter <dan.carpenter@oracle.com> Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 05 2月, 2013 1 次提交
-
-
由 Don Skidmore 提交于
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 07 12月, 2012 1 次提交
-
-
由 Joe Perches 提交于
Use the normal kernel test instead of a module specific one. Signed-off-by: NJoe Perches <joe@perches.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 22 11月, 2012 1 次提交
-
-
由 Jacob Keller 提交于
This patch enables ethtool to correctly identify flow control (pause frame) auto negotiation, as well as disallow enabling it when it is not supported. The ixgbe_device_supports_autoneg_fc function is exported and used for this purpose. There is also one minor cleanup of the device_supports_autoneg_fc by removing an unnecessary return statement. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 30 10月, 2012 1 次提交
-
-
由 Don Skidmore 提交于
Calling the ixgbe_reset_pipeline_82599 function will ensure a full pipeline reset on all 82599 devices. This is necessary to avoid possible link issues. Since this patch accomplishes this by modifying AUTOC.LMS we need to wrap all AUTOC writes when LESM is enabled. v2- fix LMS behaviour based on feedback by Martin Josefsson CC: Martin Josefsson <gandalf@mjufs.se> Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 23 10月, 2012 1 次提交
-
-
由 Wei Yongjun 提交于
Using is_zero_ether_addr() to simplify the code. Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 03 10月, 2012 1 次提交
-
-
由 joshua.a.hay@intel.com 提交于
This patch adds device support for Ethernet Controller X540-AT1. Signed-off-by: NJosh Hay <joshua.a.hay@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 20 7月, 2012 2 次提交
-
-
由 Alexander Duyck 提交于
The current logic is enabling anti-spoof on all pools and then clearing anti-spoof on just the first PF pool. The correct approach is to only set anti-spoof on the VF pools and to leave all of the PF pools unchecked. This allows for items such as FCoE to use adjacent pools within the PF for transmit and receive queues without the traffic being blocked by this security feature. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Tested-by: NSibai Li <sibai.li@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Alexander Duyck 提交于
This change corrects an issue in which an FCoE enabled adapter was always setting the FCoE SAN MAC MPSAR register to 0x1. This results in the first VF being assigned the SAN MAC address in the case of SR-IOV and as such is incorrect. To resolve this I am adding a new function that will update the SAN MAC pool address after reset. Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Tested-by: NRoss Brattain <ross.b.brattain@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 11 7月, 2012 1 次提交
-
-
由 Ben Hutchings 提交于
Fix incorrect start markers, wrapped summary lines, missing section breaks, incorrect separators, and some name mismatches. Delete a few that are content-free. Signed-off-by: NBen Hutchings <bhutchings@solarflare.com> Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 10 5月, 2012 1 次提交
-
-
由 Jacob Keller 提交于
The current value of the udelay timeout for ixgbe_disable_rx_buff is too short. This causes the security path to not not be properly disabled during the section that is meant to have it turned off. The end result causes a race condition that results in RX issues. Signed-off-by: NJacob Keller <jacob.e.keller@intel.com> Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-