This is part of what atomic must implement. And it's also required
to be able to use the helper nonblocking support.

v2: Always send out the drm event, remove the planes_changed check.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465827229-1704-1-git-send-email-daniel.vetter@ffwll.ch

Thanks to Ville Syrjälä for pointing me towards the cause of this issue.

Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:

[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config]     FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config]     scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A

Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.

A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.

Changes since v4:
 - Fix calculation of final for systems with LVDS panels (fixes BUG() on
   CI test suite)
Changes since v3:
 - Move temp variable into loop
 - Move checks for using_ssc_source to after we've figured out has_ck505
 - Add using_ssc_source to debug output
Changes since v2:
 - Fix debug output for when we disable the CPU source
Changes since v1:
 - Leave the SSC source clock on instead of just shutting it off on all
   of the DPLL configurations.

Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NLyude <cpaul@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465916649-10228-1-git-send-email-cpaul@redhat.com

Rename these remaining function prefixes to better align with the
corresponding SKL functions.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

So far we configured a static lane latency optimization during driver
loading/resuming. The specification changed at one point and now this
configuration depends on the lane count, so move the configuration
to modeset time accordingly.

It's not clear when this lane configuration takes effect. The
specification only requires that the programming is done before enabling
the port. On CHV OTOH the lanes start to power up already right after
enabling the PLL. To be safe preserve the current order and set things
up already before enabling the PLL.

v2: (Ander)
- Simplify the optimization mask calculation.
- Use the correct pipe_config always during the calculation instead
  of the bogus intel_crtc->config.

CC: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=95476Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

For all outputs except dp_mst, we have a 1:1 relationship between
connectors and encoders and the driver is relying on the atomic helpers:
we can drop the custom ->best_encoder() implementation and let the core
call drm_atomic_helper_best_encoder() for us.
Signed-off-by: NBoris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465300095-16971-7-git-send-email-boris.brezillon@free-electrons.com

- dev is redundant, we have state->atomic
- add stall parameter, which must be set when swapping needs to stall
  for preceeding commits to stop looking at ->state pointers. Currently
  all drivers need this to be, just prep work for a glorious future.

v2: Rebased on top of

commit e7cf0963
Author: Gerd Hoffmann <kraxel@redhat.com>
Date:   Tue May 31 08:50:47 2016 +0200

    virtio-gpu: add atomic_commit function

Cc: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1465509992-19284-1-git-send-email-daniel.vetter@ffwll.ch
Link: http://patchwork.freedesktop.org/patch/msgid/1465388359-8070-2-git-send-email-daniel.vetter@ffwll.ch

This reverts commit f165d283.

It breaks one of our CI systems. Quoting from Ville:

[   13.100979] [drm:ironlake_init_pch_refclk] has_panel 1 has_lvds 1 has_ck505 0 using_ssc_source 1
[   13.101413] ------------[ cut here ]------------
[   13.101429] kernel BUG at drivers/gpu/drm/i915/intel_display.c:8528!

"which is the 'BUG_ON(val != final)' at the end of ironlake_init_pch_refclk()."

Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude <cpaul@redhat.com>
Cc: marius.c.vlad@intel.com
References: https://www.spinics.net/lists/dri-devel/msg109557.htmlAcked-by: NLyude <cpaul@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

The atomic version of intel_pre_plane_update did not check
for HAS_GMCH_DISPLAY before calling intel_set_memory_cxsr().
While this doesn't cause any issues on its own (it will
return without doing anything if the hardware doesn't
have the required feature), the drm_wait_one_vblank() that
is needed if memory self-refresh is disabled introduces
an unnecessary delay in the suspend path.

In cases where i915 is on the critical path it means that
we slow down suspend by 16.8ms on platforms that don't
need to disable memory self-refresh.
Signed-off-by: NDavid Weinehall <david.weinehall@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463662236-18192-1-git-send-email-david.weinehall@linux.intel.comReviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

Apparently some CHV boards failed to hook up the port presence straps
for HDMI ports as well (earlier we assumed this problem only affected
eDP ports). So let's check the VBT in addition to the strap, and if
either one claims that the port is present go ahead and register the
relevant connector.

While at it, change port D to register DP before HDMI as we do for ports
B and C since
commit 457c52d8 ("drm/i915: Only ignore eDP ports that are connected")

Also print a debug message when we register a HDMI connector to aid
in diagnosing missing/incorrect ports. We already had such a print for
DP/eDP.

v2: Improve the comment in the code a bit, note the port D change in
    the commit message

Cc: Radoslav Duda <radosd@radosd.com>
Tested-by: NRadoslav Duda <radosd@radosd.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96321Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464945463-14364-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

If the VBT says that a certain port should be eDP (and hence fused off
from HDMI), but in reality it isn't, we need to try and acquire the HDMI
connection instead. So only trust the VBT edp setting if we can connect
to an eDP device on that port.

Fixes: d2182a66 (drm/i915: Don't register HDMI connectors for eDP ports on VLV/CHV)
References: https://bugs.freedesktop.org/show_bug.cgi?id=96288Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NPhidias Chiang <phidias.chiang@canonical.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464766070-31623-1-git-send-email-chris@chris-wilson.co.uk

This reverts the following patches:

d55dbd06 drm/i915: Allow nonblocking update of pageflips.
15c86bdb drm/i915: Check for unpin correctness.
95c2ccdc Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
a6747b73 drm/i915: Make unpin async.
03f476e1 drm/i915: Prepare connectors for nonblocking checks.
2099deff drm/i915: Pass atomic states to fbc update functions.
ee7171af drm/i915: Remove reset_counter from intel_crtc.
2ee004f7 drm/i915: Remove queue_flip pointer.
b8d2afae drm/i915: Remove use_mmio_flip kernel parameter.
8dd634d9 drm/i915: Remove cs based page flip support.
143f73b3 drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.
84fc494b drm/i915: Add the exclusive fence to plane_state.
6885843a drm/i915: Convert flip_work to a list.
aa420ddd drm/i915: Allow mmio updates on all platforms, v2.
afee4d87 Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"

"drm/i915: Allow nonblocking update of pageflips" should have been
split up, misses a proper commit message and seems to cause issues in
the legacy page_flip path as demonstrated by kms_flip.

"drm/i915: Make unpin async" doesn't handle the unthrottled cursor
updates correctly, leading to an apparent pin count leak. This is
caught by the WARN_ON in i915_gem_object_do_pin which screams if we
have more than DRM_I915_GEM_OBJECT_MAX_PIN_COUNT pins.

Unfortuantely we can't just revert these two because this patch series
came with a built-in bisect breakage in the form of temporarily
removing the unthrottled cursor update hack for legacy cursor ioctl.
Therefore there's no other option than to revert the entire pile :(

There's one tiny conflict in intel_drv.h due to other patches, nothing
serious.

Normally I'd wait a bit longer with doing a maintainer revert, but
since the minimal set of patches we need to revert (due to the bisect
breakage) is so big, time is running out fast. And very soon
(especially after a few attempts at fixing issues) it'll be really
hard to revert things cleanly.

Lessons learned:
- Not a good idea to rush the review (done by someone fairly new to
  the area) and not make sure domain experts had a chance to read it.

- Patches should be properly split up. I only looked at the two
  patches that should be reverted in detail, but both look like the
  mix up different things in one patch.

- Patches really should have proper commit messages. Especially when
  doing more than one thing, and especially when touching critical and
  tricky core code.

- Building a patch series and r-b stamping it when it has a built-in
  bisect breakage is not a good idea.

- I also think we need to stop building up technical debt by
  postponing atomic igt testcases even longer. I think it's clear that
  there's enough corner cases in this beast that we really need to
  have the testcases _before_ the next step lands.

(cherry picked from commit 5a21b665
from drm-intel-next-queeud)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

Stop yelling the plane type. "STANDARD" doesn't mean anything anyway.
Let's just use the plane name here.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-8-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Let's name our planes in a way that makes sense wrt. the spec:
- skl+ -> "plane 1A", "plane 2A", "plane 1C", "cursor A" etc.
- g4x+ -> "primary A", "primary B", "sprite A", "cursor C" etc.
- pre-g4x -> "plane A", "cursor B" etc.

v2: Rebase on top of the fixed/cleaned error paths
    Use a local 'name' variable to make things easier
v3: Pass the name as a function argument to drm_universal_plane_init() (Jani)
v3: Pass the printf style string to drm_universal_plane_init()
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-6-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Call intel_plane_destroy() instead of drm_plane_cleanup() so that we
also free the plane struct itself when bailing out of the crtc init.

And make intel_plane_destroy() NULL tolerant to avoid having to check
for it in the caller.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-5-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

v2: Fix intel_crtc leak on failure to allocate the name
    Use a local 'name' variable to make things easier
v3: Pass the name as a function arguemnt to drm_crtc_init_with_planes() (Jani)
v4: Pass the printf style format string to drm_crtc_init_with_planes()
v5: Drop spurious code changes
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

We have plane->name, so let's use that in debug messages instead
of just printing the more or less useless object ID.

v2: slap on a commit message
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

We have crtc->name, so let's use that in debug messages instead
of just printing the more or less useless object ID.

v2: Rebased due to intel_dpll_mgr.c, slap on a commit message
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464371966-15190-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

Reject the modeset if the requested dotclock exceeds the maximum allowed
by the hardware. So far we've only checked this on gen2/3 while also
handling the double wide vs. single wide pipe selection. Extend the
check to all platforms since we have the max dotclock correctly
populated now across the board.

Testcase: igt/kms_invalid_dotclock
Cc: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464114859-15610-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Thanks to Ville Syrjälä for pointing me towards the cause of this issue.

Unfortunately one of the sideaffects of having the refclk for a DPLL set
to SSC is that as long as it's set to SSC, the GPU will prevent us from
powering down any of the pipes or transcoders using it. A couple of
BIOSes enable SSC in both PCH_DREF_CONTROL and in the DPLL
configurations. This causes issues on the first modeset, since we don't
expect SSC to be left on and as a result, can't successfully power down
the pipes or the transcoders using it. Here's an example from this Dell
OptiPlex 990:

[drm:intel_modeset_init] SSC enabled by BIOS, overriding VBT which says disabled
[drm:intel_modeset_init] 2 display pipes available.
[drm:intel_update_cdclk] Current CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max CD clock rate: 400000 kHz
[drm:intel_update_max_cdclk] Max dotclock rate: 360000 kHz
vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[drm:intel_crt_reset] crt adpa set to 0xf40000
[drm:intel_dp_init_connector] Adding DP connector on port C
[drm:intel_dp_aux_init] registering DPDDC-C bus for card0-DP-1
[drm:ironlake_init_pch_refclk] has_panel 0 has_lvds 0 has_ck505 0
[drm:ironlake_init_pch_refclk] Disabling SSC entirely
… later we try committing the first modeset …
[drm:intel_dump_pipe_config] [CRTC:26][modeset] config ffff88041b02e800 for pipe A
[drm:intel_dump_pipe_config] cpu_transcoder: A
…
[drm:intel_dump_pipe_config] dpll_hw_state: dpll: 0xc4016001, dpll_md: 0x0, fp0: 0x20e08, fp1: 0x30d07
[drm:intel_dump_pipe_config] planes on this crtc
[drm:intel_dump_pipe_config] STANDARD PLANE:23 plane: 0.0 idx: 0 enabled
[drm:intel_dump_pipe_config]     FB:42, fb = 800x600 format = 0x34325258
[drm:intel_dump_pipe_config]     scaler:0 src (0, 0) 800x600 dst (0, 0) 800x600
[drm:intel_dump_pipe_config] CURSOR PLANE:25 plane: 0.1 idx: 1 disabled, scaler_id = 0
[drm:intel_dump_pipe_config] STANDARD PLANE:27 plane: 0.1 idx: 2 disabled, scaler_id = 0
[drm:intel_get_shared_dpll] CRTC:26 allocated PCH DPLL A
[drm:intel_get_shared_dpll] using PCH DPLL A for pipe A
[drm:ilk_audio_codec_disable] Disable audio codec on port C, pipe A
[drm:intel_disable_pipe] disabling pipe A
------------[ cut here ]------------
WARNING: CPU: 1 PID: 130 at drivers/gpu/drm/i915/intel_display.c:1146 intel_disable_pipe+0x297/0x2d0 [i915]
pipe_off wait timed out
…
---[ end trace 94fc8aa03ae139e8 ]---
[drm:intel_dp_link_down]
[drm:ironlake_crtc_disable [i915]] *ERROR* failed to disable transcoder A

Later modesets succeed since they reset the DPLL's configuration anyway,
but this is enough to get stuck with a big fat warning in dmesg.

A better solution would be to add refcounts for the SSC source, but for
now leaving the source clock on should suffice.

Changes since v3:
 - Move temp variable into loop
 - Move checks for using_ssc_source to after we've figured out has_ck505
 - Add using_ssc_source to debug output
Changes since v2:
 - Fix debug output for when we disable the CPU source
Changes since v1:
 - Leave the SSC source clock on instead of just shutting it off on all
   of the DPLL configurations.

Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NLyude <cpaul@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1464199863-9397-1-git-send-email-cpaul@redhat.com

I noticed that during S4 resume BIOS incorrectly sets bits 18, 19 which
are reserved/MBZ and sets the decimal frequency fields to all 0xff in
the CDCLK register. The result is a hard lockup as display register
accesses are attempted later. Work around this by sanitizing the CDCLK
PLL/dividers the same way it's done on SKL.

While this is clearly a BIOS bug which should be fixed separately, it
doesn't hurt to check/sanitize this regardless.

v2:
- Use the same condition for VCO and CDCLK in broxton_init_cdclk as is
  used in skl_init_cdclk for the same purpose.

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464093513-16258-2-git-send-email-imre.deak@intel.com

If the CDCLK PLL isn't locked or incorrectly configured we can just
assume that it's off resulting in fully re-initializing both CDCLK PLL
and CDCLK dividers. This way the CDCLK PLL sanitization added in the
following patch can be done on BXT the same way as it's done on SKL.

v2: (Ville)
- Remove the remaining PLL specific checks from skl_sanitize_cdclk() and
  depend instead on the corresponding check in skl_dpll0_update().
- Use vco == 0 instead of the corresponding boolean check in
  skl_sanitize_cdclk().

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1464093513-16258-1-git-send-email-imre.deak@intel.com

This reverts the following patches:

d55dbd06 drm/i915: Allow nonblocking update of pageflips.
15c86bdb drm/i915: Check for unpin correctness.
95c2ccdc Reapply "drm/i915: Avoid stalling on pending flips for legacy cursor updates"
a6747b73 drm/i915: Make unpin async.
03f476e1 drm/i915: Prepare connectors for nonblocking checks.
2099deff drm/i915: Pass atomic states to fbc update functions.
ee7171af drm/i915: Remove reset_counter from intel_crtc.
2ee004f7 drm/i915: Remove queue_flip pointer.
b8d2afae drm/i915: Remove use_mmio_flip kernel parameter.
8dd634d9 drm/i915: Remove cs based page flip support.
143f73b3 drm/i915: Rework intel_crtc_page_flip to be almost atomic, v3.
84fc494b drm/i915: Add the exclusive fence to plane_state.
6885843a drm/i915: Convert flip_work to a list.
aa420ddd drm/i915: Allow mmio updates on all platforms, v2.
afee4d87 Revert "drm/i915: Avoid stalling on pending flips for legacy cursor updates"

"drm/i915: Allow nonblocking update of pageflips" should have been
split up, misses a proper commit message and seems to cause issues in
the legacy page_flip path as demonstrated by kms_flip.

"drm/i915: Make unpin async" doesn't handle the unthrottled cursor
updates correctly, leading to an apparent pin count leak. This is
caught by the WARN_ON in i915_gem_object_do_pin which screams if we
have more than DRM_I915_GEM_OBJECT_MAX_PIN_COUNT pins.

Unfortuantely we can't just revert these two because this patch series
came with a built-in bisect breakage in the form of temporarily
removing the unthrottled cursor update hack for legacy cursor ioctl.
Therefore there's no other option than to revert the entire pile :(

There's one tiny conflict in intel_drv.h due to other patches, nothing
serious.

Normally I'd wait a bit longer with doing a maintainer revert, but
since the minimal set of patches we need to revert (due to the bisect
breakage) is so big, time is running out fast. And very soon
(especially after a few attempts at fixing issues) it'll be really
hard to revert things cleanly.

Lessons learned:
- Not a good idea to rush the review (done by someone fairly new to
  the area) and not make sure domain experts had a chance to read it.

- Patches should be properly split up. I only looked at the two
  patches that should be reverted in detail, but both look like the
  mix up different things in one patch.

- Patches really should have proper commit messages. Especially when
  doing more than one thing, and especially when touching critical and
  tricky core code.

- Building a patch series and r-b stamping it when it has a built-in
  bisect breakage is not a good idea.

- I also think we need to stop building up technical debt by
  postponing atomic igt testcases even longer. I think it's clear that
  there's enough corner cases in this beast that we really need to
  have the testcases _before_ the next step lands.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Acked-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: NDave Airlie <airlied@redhat.com>
Acked-by: NJani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>

In case the driver is initialized without active displays, we should
just drop the cdclk to the minimum frequency right off the bat. There
might not be a modeset to drop it to the minimum late rafter all.

With DMC supposedly we should always have the cdclk up and running.
The DMC will shut the DE PLL down when appropriate, so let's nuke
the related FIXMEs as well. Trying to do anything different would
go against the expectations of the DMC firmware, and we all know
how fragile the DMC firmware is.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-22-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Rather than having a BXT specific function to make sure the DE PLL is
enabled after disabling DC6, let's just make sure the current cdclk
is the same as what we last programmed.

Having another check in bxt_display_core_init() almost immediately after
the cdclk init seems redundant, so let's just kill that one.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-21-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Make bxt_set_cdclk() more readable by looking at current vs. target
DE PLL vco to determine if the DE PLL needs disabling and/or enabling.
We can also calculate the CD2X divider simply as (vco/cdclk) instead of
depending on magic numbers.

The magic numbers are still needed though, but only to map the supported
cdclk frequencies to corresponding DE PLL frequencies.

Note that w'll now program CDCLK_CTL correctly even for the bypass case.
Actually the CD2X divider should not matter in that case since the
hardware will bypass it too, but the "decimal" part should matter (if we
want to do gmbus/aux with the bypass enabled).
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-20-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Now that we've read out the DE PLL vco and refclk, we can just use them
in the cdclk calculation. While at it switch over to
DIV_ROUND_CLOSEST().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-19-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Let's make sure our cached cdclk state is accurate right after
broxton_init_cdclk() whether or not we end up changing the cdclk
frequency.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-18-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

We have need to know the DE PLL refclk and output frequency in various
cdclk calculations, so let's store those in dev_priv.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-17-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Enabling and disalbing the DE PLL are two nice self contained
operations, so let's move them into a few small helper functions.
Makes it easier to see the forest from the trees in broxton_set_cdclk().
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-16-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Future platforms will have multiple options for the cdclk PLL reference
clock, so let's start tracking that under dev_priv alreday on SKL,
although on SKL it's always 24 MHz.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-15-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

We'll want to store the cdclk PLL (whatever PLL that is in reality) vco
frequency somewhere on other platforms too, so let's rename the
skl_vco_freq to cdclk_pll.vco, and let's store it in kHz instead of MHz
to match most of the other clocks.

v2: Drop the spurious > vs != change (Imre)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-14-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The SKL 308.57 MHz cdclk is probably 8640/28 = ~308.571 Mhz.
Similartly the 617.14 MHz cdclk is probably 8640/14 = ~617.143 MHz.
Let's use the slightly more accurate numbers. Potentially we might
change to computing all of these based on dividers, but let's
stick to the current theme for now..
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-13-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

SKL and BXT have the same snippets of code for enabling disabling the
DBUF. Extract those into helpers and move the calls from
init/unit_cdclk() to the display core init/init since this stuff isn't
really about cdclk. Also doing the enable twice shouldn't hurt since
you're just setting the request bit again when it was already set.

We can also toss in a few WARNs about the register values into
skl_get_dpll0_vco() now that we know that things should always be
sane there.

Flatten skl_init_cdclk() while at it.

v2: s/skl/gen9/ in function names (Imre)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-12-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Currently we initialize cdclk on SKL from two different places,
depending on whether it's during driver init or resume. Let's
unify it to happen from the same place always, and that place will be
the display core init function.

To do this we first run through the cdclk sanitation code, which will
first verify that the PLL is programmed correctly, after which we can
read out the current cdclk frequency, and once the cdclk is known we
verify that the cdclk "decimal" frequency is programmed correctly. If
any of these fail we will force a cdclk change, and to be safe we also
force the PLL to be turned off and on again. If the sanitation step
didn't notice anything amiss, we'll skip the cdclk programming which
will prevent cdclk reprogramming when the displays might be active.

We can also toss in a few WARNs about the register values into
skl_update_dpll0() since we now know that the PLL state should
always be sane when that function is called.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-11-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Also verify the DPLL_CTRL1 register value in skl_sanitize_cdclk(), throw
out a few unneeded variables, and write the CDCLK_CTL check a bit more
legible way.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-10-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Now that skl_vco_freq tracks the actual DPLL0 vco frequency, we'll need
something that keeps track of which vco frequency we want to use in case
the current vco is 0. This would be important across supend/resume since
we'll disable DPLL0 around those parts.

We'll also update our idea of max cdclk/dotclock when the preferred
vco changes. That could happen if out initial guess was wrong, and
later eDP would force us to change it. One issue here could be that
changing the max dotclock could cause our mode list to change during
next time the displays get probed. But I don't see a good way to avoid
that, except perhaps by allowing either vco frequency to be used as
needed. But the docs suggest that such usage wasn't really inteded.

Also need to make sure we don't update our max_cdclk value before we
have a preferred vco value, which means moving that to happen after
the cdclk sanitation.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-9-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

In case we originally guessed wrong which lcpll vco frequency to use,
we will need to shut down the pll and restart it when reprogamming the
cdclk.

This also allows us to track the actual vco frequency in dev_priv
instead of just a guess.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-8-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-7-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Currently we're trying to guess which lcpll vco frequency is used
use based on the cdclk. That doesn't work for cdclk==540 since
both vco frequencies can generate a 540 Mhz output. Let's stop
guessing and just read the actual vco frequency from the
hardware.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-6-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

We have many places where we want to pick a suitable cdclk frequency for
skl based on the dotclock and lcpll vco. Split that code into a small
helper and call it from all over.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1463172100-24715-5-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>