- 28 9月, 2005 4 次提交
-
-
由 David S. Miller 提交于
Written by Adrian Sun (asun@darksunrising.com). Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>. Further cleaned up and integrated by David S. Miller Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Fix interrupt test handler by adding check for IRQ assertion in PCI_STATE register in addition to the status block updated bit. Add test for valid ethernet address in tg3_set_mac_addr(). Add tg3_bus_string() to setup the PCI bus speed/width string for all PCI/PCIX/PCI Express devices. This is used to print the bus type during init_one(). Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
Fix 5780 PHY related problems: 1. MAC_RX_MODE reset must be done before setting up the MAC_MODE register on 5705_PLUS chips or the chip will stop receiving after a while. The MAC_RX_MODE reset is needed to prevent intermittently losing the first receive packet on serdes chips. 2. Skip MAC loopback test on 5780 because of hardware errata. Normal traffic including PHY loopback is not affected by the errata. 3. PHY loopback fails intermittently on 5708S and this is fixed by putting the PHY in loopback mode first before programming the MAC mode register. A MAC_RX_MODE reset is also added. 4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow nway_reset if 5780S is in parallel detect mode. 5. Add missing PHY IDs in KNOWN_PHY_ID() macro. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 9月, 2005 1 次提交
-
-
由 Al Viro 提交于
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 24 9月, 2005 1 次提交
-
-
由 Stephen Hemminger 提交于
This is one of those workarounds sucked over from sk98lin driver. The skge driver needs to detect the Yukon-Lite A0 chip properly, and turn of Rx FIFO Flush. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 23 9月, 2005 1 次提交
-
-
由 Paul Gortmaker 提交于
While this is true, E8390_CMD is zero on i386, and thus there should be no effect for these machines. Machines like Mac, Amiga etc. which use Alan's clever register mapping may have a non-zero E8390_CMD and result in bogus "transmitter busy" type messages from this bug. Fixes BUG# 3991.
-
- 22 9月, 2005 4 次提交
-
-
由 Tommy Christensen 提交于
vlan_hwaccel_rx should be used when in interrupt context. Fixes bug http://bugzilla.kernel.org/show_bug.cgi?id=5284Signed-off-by: NTommy S. Christensen <tommy.christensen@tpack.net> Cc: Francois Romieu <romieu@fr.zoreil.com> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Cleanup receive buffer allocation and management, Add more error handling checks from PHY and bump version. Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Expand the returned data for ethtool debug access to include all of the mapped PCI area; except for the small set of registers that are for diagnostic RAM access. Access to those registers will hang the system. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 nsxfreddy@gmail.com 提交于
Fix bond_enslave link monitoring warning to check use_carrier status and ethtool_ops in addition to do_ioctl. This version checks ethtool_ops as well as do_ioctl, and also uses the per-bond params.use_carrier instead of the global use_carrier. Signed-off-by: NJason R. Martin <nsxfreddy@gmail.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 20 9月, 2005 1 次提交
-
-
由 Krzysztof Halasa 提交于
The following commit breaks cisco mode with my WAN drivers: author David S. Miller <davem@davemloft.net> Tue, 28 Jun 2005 22:25:31 +0000 (15:25 -0700) commit 689be439 "[NET]: Remove gratuitous use of skb->tail in network drivers." The following patch fixes it - please apply (cisco_hard_header does skb_push(4 bytes)). Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 18 9月, 2005 1 次提交
-
-
由 Florin Malita 提交于
From: Florin Malita <fmalita@gmail.com> bond_init() is not releasing rtnl_sem after register_netdevice() and before calling unregister_netdevice() (from bond_free_all()) in the exception path. As the device registration is not completed (dev->reg_state == NETREG_REGISTERING), the call to unregister_netdevice() triggers BUG_ON(dev->reg_state != NETREG_REGISTERED). Signed-off-by: NFlorin Malita <fmalita@gmail.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 17 9月, 2005 3 次提交
-
-
由 Michael Chan 提交于
Fix and simplify the workaround code for the 4GB boundary tx buffer hardware bug. 1. Need to unmap the original SKB's dma addresses if a new SKB cannot be allocated. 2. Need to pass the base flag to tigon3_4gb_hwbug_workaround() or TSO won't work properly. 3. The guilty entry and length parameters for tigon3_4gb_hwbug_workaround() are removed as they are not necessary. 4. Remove assumption that only one fragment can hit the 4GB boundary. Another fragment can hit 8GB for example. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Peter Hagervall 提交于
Change 0 to NULL where appropriate. Signed-off-by: NPeter Hagervall <hager@cs.umu.se> Acked-by: NJeff Garzik <jgarzik@pobox.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
Thanks to Andy Stewart for the report and testing debug patches from Michael Chan. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 9月, 2005 3 次提交
-
-
由 Jens Osterkamp 提交于
This patch makes the driver work with any BladeCenter network switch, it used to work only with certain models. Please apply. Signed-off-by: NArnd Bergmann <arndb@de.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Don't crash if ethtool statistics are requested and device is down. Fix is to allocate pci space for statistics only when needed. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Jay Vosburgh 提交于
Bonding leaks route structures when the ARP monitor is configured to send probes over VLANs. Originally reported by Ian Abel <ian.abel@mxtelecom.com>; his original fix was modified by Jay Vosburgh to correct coding style and to close a leak it missed. Signed-off-by: NJay Vosburgh <fubar@us.ibm.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 14 9月, 2005 8 次提交
-
-
由 Stephen Hemminger 提交于
Merge of four previous patches and the Kconfig fix * Remove debug printk's * whitespace cleanup and version number change * clear interrupts, reset phy, and reset hardware on shutdown * ignore 64bit counter overflow interrupts * fix a couple of places where second port could clobber state of first port. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 John W. Linville 提交于
Do not count frames dropped by the hardware as part of rx_dropped. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 John W. Linville 提交于
Do not count non-error frames dropped by the hardware as part of rx_dropped. Instead, count those frames dropped as rx_missed_errors. Also, do not count other error frames as part of rx_dropped. Finally, do not count oversized frames in rx_dropped (since they are counted as part of rx_length_errors). Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 John W. Linville 提交于
Do not count frames dropped by the hardware as part of rx_dropped. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 matthieu castet 提交于
this patch display the correct channel number with iwlist scan Signed-off-by: NMatthieu CASTET <castet.matthieu@free.fr> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Keith Owens 提交于
xircom_cb.c does #if CONFIG_NET_POLL_CONTROLLER instead of #ifdef, resulting in drivers/net/tulip/xircom_cb.c:120:5: warning: "CONFIG_NET_POLL_CONTROLLER" is not defined. Signed-off-by: NKeith Owens <kaos@sgi.com> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Andrew Morton 提交于
drivers/net/s2io.c: In function `init_shared_mem': drivers/net/s2io.c:431: warning: cast from pointer to integer of different size drivers/net/s2io.c: In function `free_shared_mem': drivers/net/s2io.c:662: warning: cast from pointer to integer of different size Cc: "David S. Miller" <davem@davemloft.net> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
由 Stephen Hemminger 提交于
Fix PCI device id issues with sk98lin driver. 1. DLINK 530-T card has no Vital Product Data (VPD) area so the sk98lin driver won't work. (skge does however) 2. Remove commented out Yukon2 stuff 3. Restrict Linksys card to revisions that don't conflict with r8169 version. Signed-off-by: NStephen Hemminger <shemminger@osdl.org> Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
-
- 13 9月, 2005 7 次提交
-
-
由 Peter Osterlund 提交于
Remove check_region references from comments and printk statements so that searching for real users of this deprecated function gets easier. Signed-off-by: NPeter Osterlund <petero2@telia.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Komuro 提交于
Add new id to orinoco_cs (corega PCCB-11). Signed-off-by: <komurojun-mbn@nifty.com> Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 John W. Linville 提交于
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 John W. Linville 提交于
Instead, count them as part of rx_missed_errors. Signed-off-by: NJohn W. Linville <linville@tuxdriver.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ralf Baechle 提交于
Rename ax25_encapsulate to ax25_hard_header which these days more accurately describes what the function is supposed to do. Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ralf Baechle 提交于
Misc related cleanups in hamradio drivers: o Use symbolic constants instead of magic numbers o Don't try to handle the case where AX.25 isn't configured - the kernel configuration doesn't permit that. o Remove useless headers Signed-off-by: NRalf Baechle DL5RB <ralf@linux-mips.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 12 9月, 2005 5 次提交
-
-
由 Greg Ungerer 提交于
Add support for the FEC ethernet driver of the Freescale 523x processor family to the FEC header definitions. Signed-off-by: NGreg Ungerer <gerg@uclinux.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Greg Ungerer 提交于
A few improvements to the Freescale/ColdFire FEC driver: . some formatting cleanups . add support for the FEC device in the ColdFire 523x processor family . add support for MAC address setting on MOD5272 and M5272C3 boards . don't re-read the PHY status register many times . ack status interrupt before reading status register . move printing init message to after full init (so that the ethX name is filled out for printing) Some parts of this patch submitted by Philippe De Muyter <phdm@macqel.be> Signed-off-by: NGreg Ungerer <gerg@uclinux.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Greg Ungerer 提交于
Add configuration support for the FEC ethernet controller in the Freescale 523x processor family. Also add and option to configure the second FEC controller on some Freescale processors. Signed-off-by: NGreg Ungerer <gerg@uclinux.com> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Willy Tarreau 提交于
This ports the Sun GEM ROM mapping/enable fixes it sunhme (which used the same PCI ROM mapping code). Without this, I get NULL MAC addresses for all 4 ports (it's a SUN QFE). With it, I get the correct addresses (the ones printed on the label on the card). Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
由 Linus Torvalds 提交于
This same patch was reported to fix the MAC address detection on sunhme (next patch). Most people seem to be running this on Sparcs or PPC machines, where we get the MAC address from their respective firmware rather than from the (previously broken) ROM mapping routines. Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-
- 11 9月, 2005 1 次提交
-
-
由 Domen Puncer 提交于
s/for/list_for_each/ Signed-off-by: NMaximilian Attems <janitor@sternwelten.at> Signed-off-by: NDomen Puncer <domen@coderock.org> Cc: Jeff Garzik <jgarzik@pobox.com> Signed-off-by: NAndrew Morton <akpm@osdl.org> Signed-off-by: NLinus Torvalds <torvalds@osdl.org>
-