This allows the basic registers of the general register files to be supplied
by a syscon instead of being mapped locally.

The GRF registers contain a lot more than pinctrl functions like dma, usb-phy
and general soc control and status registers, intermixed with the iomux, pull
and drive-strength registers.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When the pmu registers are supplied through a syscon regmap we do not need
to map the registers ourself.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Currently the pmu registers containing pin pull settings on the rk3188 are mapped
locally when bank0 is instantiated. Add an alternative that can resolve the pmu
from a syscon phandle.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Convert rockchip_get_bank_data to use the struct rockchip_pinctrl because
later on we need to check a value from it when registering the gpio banks.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This allows us to use syscons in the future.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Deprecate secondary register area for rk3188 pulls. Instead use big enough
initial mapping of grf registers to catch all.

The now deprecated register is still supported though.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NMax Schwarz <max.schwarz@online.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Pinctrl cleanup and reworks for 3.16

This serie of patch:
  - Moves the Allwinner pinctrl driver to a folder of its own
  - removes the sunxi-pinctrl-pins header, and split the driver into a core
    one, with all the logic, and smaller drivers, one for each SoC, that
    declare the pins, and will provide to the core the set of pins.
  - And does a few cleanups here and there.

The way that reset is handled right now is that it is made optional for every
pinctrl driver, while actually, it isn't used at all for the main pin
controllers so far, and while it's mandatory for the A31's secondary pin
controller.

Move the reset functions out of the core and in the driver, where they can be
made mandatory.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add one Kconfig option for each driver. This will allow to better control which
driver is enabled, instead of having either all or nothing.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be.

This is the final step toward retiring pinctrl-sunxi-pins.h that used to define
all the pins for all the Allwinner SoCs in a single header, that would have in
turn result in having these structures in the final binary as many times as the
header was included.

We can finally remove that header, and remove all the driver part of the
pinctrl-sunxi core.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Move the pin description to a driver specific to be. This is one more step
toward retiring pinctrl-sunxi-pins.h that used to define all the pins for all
the Allwinner SoCs in a single header, that would have in turn result in having
these structures in the final binary as many times as the header was included.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This will allow to have multiple drivers using the same core code, and
eventually, retire pinctrl-sunxi-pins.h
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The previous code was calling of_iomap, which doesn't do any resource
management, and doesn't call request_mem_region either. Use
devm_ioremap_resource that do both.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

We previously had an evergrowing (and exhaustive) list of the pins that could
be used on any Allwinner SoCs. These defines were then used by each pinctrl
driver to declare the list of functions for this pin. Since it's pretty much
all boilerplate, we can remove it just by a single macro.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This will allow to create numerous files without crippling the main pinctrl
directory.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The ranges and nranges were never used. Remove them.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The pins description structure were declared as const, but the of_device_id
data magic was losing it silently.

Make sure we have it on both sides.

And now that we're using const, we can also remove the useless cast in probe.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Fix copy/paste error in pinctrl_pin_desc for pin 0.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This commit extends the pinctrl mvebu logic with a new driver to cover
Orion5x SoC. It supports the definitions for the 5181l, 5182 and 5281
variants of Orion5x, which are the three ones supported by the old
style MPP code in arch/arm/mach-orion5x/.
Signed-off-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

In some cases it is nice to be able to simply control a gpio output
via the PIN_CONFIG_OUTPUT option without having a driver control it.
Thus add support for it to the rockchip pinctrl driver.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Till now pinconf_get only set the argument value into the config parameter
effectively removing the actual config param value. As other pinctrl drivers
do, it might be nicer to keep the config param intact.
Therefore construct a real pinconfig value from param and arg in pinconf_get
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This switches the SiRF pinctrl driver over to using the gpiolib
irqchip helpers simplifying some of the code.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

all gpio banks are in one chip, that makes software clean in mapping
irq and gpio.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The sirfsoc_irqchip_to_bank() is obviously misnamed, as it is
not converting an irqchip to a bank but converts a gpiochip
to a bank so rename it sirfsoc_gpiochip_to_bank().
Acked-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Define a new binding for the Qualcomm TLMMv2 based pin controller inside the
IPQ8064.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Reviewed-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds pinctrl definitions for the GPIO pins of the TLMM v2 block in the
Qualcomm IPQ8064 platform.
Signed-off-by: NAndy Gross <agross@codeaurora.org>
Reviewed-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

List all sunxi pinctrl compatible strings in order to be able to grep for
those values.
Signed-off-by: NBoris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds driver data (bank list and EINT layout) for Exynos3250
to pinctrl-exynos driver. Exynos3250 includes 158 multi-functional input/output
ports. There are 23 general port groups.

Changes from v1:
- Add signed-off of sender
- Post only separated patch for pinctrl from following patchset(v1)
  : https://lkml.org/lkml/2014/4/10/286

Cc: Thomas Abraham <thomas.abraham@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NChanwoo Choi <cw00.choi@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

pin_to_mask expects a bank pin number. So do not add the chip base.

Without that patch cat /sys/kernel/debug/gpio looks like that:
GPIOs 0-31, platform/fffff200.gpio, fffff200.gpio:
[spi32766.0] GPIOfffff200.gpio5: [gpio] set
[ads7846_pendown] GPIOfffff200.gpio15: [gpio] set
[ohci_vbus] GPIOfffff200.gpio21: [gpio] set
[ohci_vbus] GPIOfffff200.gpio24: [gpio] set
[button1] GPIOfffff200.gpio28: [gpio] clear
[button2] GPIOfffff200.gpio29: [gpio] clear

GPIOs 32-63, platform/fffff400.gpio, fffff400.gpio:
[sda] GPIOfffff400.gpio4: [periph A]
[scl] GPIOfffff400.gpio5: [periph A]
[spi32766.3] GPIOfffff400.gpio11: [periph A]
[error] GPIOfffff400.gpio22: [periph A]
[run] GPIOfffff400.gpio23: [periph A]

GPIOs 64-95, platform/fffff600.gpio, fffff600.gpio:
[reset_pin] GPIOfffff600.gpio29: [periph A]

GPIOs 96-127, platform/fffff800.gpio, fffff800.gpio:
[led1] GPIOfffff800.gpio5: [periph A]
[led2] GPIOfffff800.gpio6: [periph A]
[led3] GPIOfffff800.gpio7: [periph A]
[led4] GPIOfffff800.gpio8: [periph A]

GPIOs 128-159, platform/fffffa00.gpio, fffffa00.gpio:
[button3] GPIOfffffa00.gpio10: [periph A]
[button4] GPIOfffffa00.gpio12: [periph A]

Note that every bank despite bank 0 only shows "periph A" which are
obviously used as GPIOs.
Signed-off-by: NAlexander Stein <alexanders83@web.de>
Acked-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This converts the AT91 pin control driver to register its
chained irq handler and irqchip using the helpers in the
gpiolib core.
Signed-off-by: NAlexander Stein <alexanders83@web.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The kerneldoc for struct tegra_pingroup didn't describe all of the fields
in the struct. Add some extra kerneldoc to fix that.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When an attempt is made to configure an unsupported option on a pin,
print the DT property name of that option, so it's easier to debug
what the problem is.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The range of npins and function ID values is small enough to fit into a
u8. Use this type rather than unsigned to shrink the pinmux data tables.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The fsafe value in the pingroup data tables is only used to implement
tegra_pinctrl_disable(). The only reason this function is called is when
dynamically switching between pinmux states, i.e. when disabling the old
state before programming the new state. It's simpler to have the new
target state define the expected value of each pin (and all current DTs
do that). This also gives more flexibility, since it allows individual
boards explicit control over the "inactive" mux function for each pin,
rather than requiring it to be an SoC-specific value. Assuming this, we
can get rid of the fsafe value from the driver completely, thus saving
some more space in the driver tables.

While re-writing the content of tegra124_pingroups[], fix the indentation
to use a TAB instead of spaces.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Any SoC which supports the einput, odrain, lock, ioreset, or rcv_sel
options has the relevant HW register fields in the same register as the
mux function selection. Similarly, the drvtype option is always in the
drive register, if it is supported at all. Hence, we don't need to have
struct *_reg fields in the pin group table to define which register and
bank to use for those options. Delete this to save space in the driver's
data tables.

However, many of those options are not supported on all SoCs, or not
supported on some pingroups. We need a way to detect when they are
supported. Previously, this was indicated by setting the struct *_reg
field to -1. With the struct *_reg fields removed, we use the struct
*_bit fields for this purpose instead. The struct *_bit fields need to
be expanded from 5 to 6 bits in order to store a value outside the valid
HW bit range of 0..31.

Even without removing the struct *_reg fields, we still need to add code
to validate the struct *_bit fields, since some struct *_bit fields were
already being set to -1, without an option-specific struct *_reg field to
"guard" them. In other words, before this change, the pinmux driver might
allow some unsupported options to be written to HW.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Signed-off-by: NWolfram Sang <wsa@sang-engineering.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>