The kernel was allowing any component of the pt_regs to be updated either
by signal handlers writing to the stack, or by processes writing via
PTRACE_POKEUSR or PTRACE_SETREGS, which meant they could set their PL
up from 0 to 1 and get access to kernel code and data (or, in practice,
cause a kernel panic).  We now always reset the ex1 field, allowing the
user to set their ICS bit only.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

This change is modelled on similar fixes for other architectures.
The pt_regs "faultnum" member is set to the trap (fault) number that
caused us to enter the kernel, and is INT_SWINT_1 for the syscall software
interrupt.  We already supported a pseudo value, INT_SWINT_1_SIGRETURN,
that we used for the rt_sigreturn syscall; it avoided the case where
one signal was handled, then we "tail-called" to another handler.

This change avoids the similar case where we start to call one handler,
then are preempted into another handler when we start trying to run
the first handler.  We clear ->faultnum after calling handle_signal(),
and to be paranoid also in the case where there was no signal to deliver.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

For the "initfree" boot argument it's not that big a deal, but
to avoid warnings in the code, we check for a valid value before
allowing the specified argument to override the kernel default.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

This completes the tile migration to the new naming scheme for
the architecture-specific irq management code.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

This change makes KM_TYPE_NR independent of the actual deprecated
list of km_type values, which are no longer used in tile code anywhere.
For now we leave it set to 8, allowing that many nested mappings,
and thus reserving 32MB of address space.

A few remaining places using KM_* values were cleaned up as well.
Signed-off-by: NChris Metcalf <cmetcalf@tilera.com>

This fixes an erroneous use of LSB first in the U300 machine, the
PL022 used in U300 is a standard ARM core that doesn't support this
bit so it should never have been set.

Cc: Kevin Wells <wellsk40@gmail.com>OA
Signed-off-by: NLinus Walleij <linus.walleij@stericsson.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Russ Anderson reported:
| There is a regression that is causing a NULL pointer dereference
| in free_irte when shutting down xpc. git bisect narrowed it down
| to git commit d585d060(intr_remap: Simplify the code further), which
| changed free_irte(). Reverse applying the patch fixes the problem.

We need to use irq_remapped() for each irq instead of checking only
intr_remapping_enabled as there might be non remapped irqs even when
remapping is enabled.

[ tglx: use cfg instead of retrieving it again. Massaged changelog ]
Reported-bisected-and-tested-by: NRuss Anderson <rja@sgi.com>
Signed-off-by: NYinghai Lu <yinghai@kernel.org>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4CCBD511.40607@kernel.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Register UDA1380 codec during H1940 machine init
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Current implementation of LCD and backlight power control functions
is not complete, as result PDA consumes power in suspend.
Fix this issue by managing state of some latch bits, just like
WinMobile does.
Signed-off-by: NVasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Currently, text_poke_smp() passes a NULL as the third argument to
__stop_machine(), which will only run stop_machine_text_poke()
on 1 cpu. Change NULL -> cpu_online_mask, as stop_machine_text_poke()
is intended to be run on all cpus.

I actually didn't notice any problems with stop_machine_text_poke()
only being called on 1 cpu, but found this via code inspection.
Signed-off-by: NJason Baron <jbaron@redhat.com>
LKML-Reference: <20101028152026.GB2875@redhat.com>
Acked-by: NMathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: NMasami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: NH. Peter Anvin <hpa@linux.intel.com>

Recent changes in s3c gpio break mini2440 board and may be others.
The problem is that mach-mini2440.c: mini2440_init()
(where we call s3c_gpio_setpull()) is called before s3c2440.c: s3c2440_init()
(where we initialize s3c24xx_gpiocfg_default.set_pull function pointer).
This causes dereferencing of NULL pointer at boot time and a kernel panic.
Signed-off-by: NAbdoulaye Walsimou Gaye <awg@embtoolkit.org>

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

* kconfig symbols defined in arch/arm/mach-s3c2440/Kconfig are only available
  when ARCH_S3C2410 is selected, so no need to make some of them depend
  on ARCH_S3C2410.
* fix CPU_S3C24405B typo in "config S3C2440_DMA".
* mini2440: remove unconditionally select of SND_S3C24XX_SOC_S3C24XX_UDA134X.
Those fixes avoid the following warnings at make time:

scripts/kconfig/qconf arch/arm/Kconfig
warning: (MACH_MINI2440 && ARCH_S3C2410) selects SND_S3C24XX_SOC_S3C24XX_UDA134X
which has unmet direct dependencies (SND_S3C24XX_SOC && ARCH_S3C2410)
warning: (CPU_S3C2440 && ARCH_S3C2410 && S3C2410_DMA) selects S3C2440_DMA which
has unmet direct dependencies (ARCH_S3C2410 && CPU_S3C24405B)
warning: (CPU_S3C2440 && ARCH_S3C2410 || CPU_S3C2442 && ARCH_S3C2410)
selects CPU_S3C244X which has unmet direct dependencies (!ARCH_S3C2410)
Signed-off-by: NAbdoulaye Walsimou Gaye <awg@embtoolkit.org>

Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

These two config options don't exist, and aren't ever going to.
So I simply delete them.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

If the board has a debug uart the user is given a choice of which
uart to use. The user can also select NONE, which means not to use one.
In most of our header files when NONE is selected nothing is defined
for MSM_DEBUG_UART_PHYS or MSM_DEBUG_UART_BASE. This causes a compile
failure in debug-macro.S which expect something to be defined there.

Example of the failure,

arch/arm/kernel/built-in.o: In function `hexbuf':
linux-2.6/arch/arm/kernel/debug.S:186: undefined reference to `MSM_DEBUG_UART_PHYS'
linux-2.6/arch/arm/kernel/debug.S:186: undefined reference to `MSM_DEBUG_UART_BASE'

This fixes the compile failure by adding an ifdef to debug-macro.S
that removes all the debug uart code in the case of NONE.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

Originally there was an ifdef case to handle when no debug uart
was selected. In commit 0ea12930
that case was removed which causes the following build failure,

linux-2.6/arch/arm/kernel/debug.S: Assembler messages:
linux-2.6/arch/arm/kernel/debug.S:174: Error: bad instruction `addruart r1,r2'
linux-2.6/arch/arm/kernel/debug.S:176: Error: bad instruction `waituart r2,r3'
linux-2.6/arch/arm/kernel/debug.S:177: Error: bad instruction `senduart r1,r3'
linux-2.6/arch/arm/kernel/debug.S:178: Error: bad instruction `busyuart r2,r3'
linux-2.6/arch/arm/kernel/debug.S:190: Error: bad instruction `addruart r1,r2'

This is a partial revert to add back the case which was removed with
two caveats. First the API for the addruart macro was updated, and
the new addruart case now return 0xfff00000 so that a know IO mapping
is created instead of a random one.

Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jason Wang <jason77.wang@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>

On i386 (not x86_64) early implementations of gcc would have a bug
with asm goto causing it to produce code like the following:

(This was noticed by Peter Zijlstra)

   56 pushl 0
   67 nopl         jmp 0x6f
      popl
      jmp 0x8c

   6f              mov
                   test
                   je 0x8c

   8c mov
      call *(%esp)

The jump added in the asm goto skipped over the popl that matched
the pushl 0, which lead up to a quick crash of the system when
the jump was enabled. The nopl is defined in the asm goto () statement
and when tracepoints are enabled, the nop changes to a jump to the label
that was specified by the asm goto. asm goto is suppose to tell gcc that
the code in the asm might jump to an external label. Here gcc obviously
fails to make that work.

The bug report for gcc is here:

  http://gcc.gnu.org/bugzilla/show_bug.cgi?id=46226

The bug only appears on x86 when not compiled with
-maccumulate-outgoing-args. This option is always set on x86_64 and it
is also the work around for a function graph tracer i386 bug.
(See commit: 746357d6)
This explains why the bug only showed up on i386 when function graph
tracer was not enabled.

This patch now adds a CONFIG_JUMP_LABEL option that is default
off instead of using jump labels by default. When jump labels are
enabled, the -maccumulate-outgoing-args will be used (causing a
slightly larger kernel image on i386). This option will exist
until we have a way to detect if the gcc compiler in use is safe
to use on all configurations without the work around.

Note, there exists such a test, but for now we will keep the enabling
of jump label as a manual option.

Archs that know the compiler is safe with asm goto, may choose to
select JUMP_LABEL and enable it by default.
Reported-by: NIngo Molnar <mingo@elte.hu>
Cause-discovered-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Baron <jbaron@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Miller <davem@davemloft.net>
Cc: Richard Henderson <rth@redhat.com>
LKML-Reference: <1288028746.3673.11.camel@laptop>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

commit 534af108(kgdb,kdb: individual
register set and and get API) introduce dbg_get_reg/dbg_set_reg API
for individual register get and set.

This patch implement those APIs for ppc.
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

The kgdb_disable_hw_debug() was an architecture specific function for
disabling all hardware breakpoints on a per cpu basis when entering
the debug core.

This patch will remove the weak function kdbg_disable_hw_debug() and
change it into a call back which lives with the rest of hw breakpoint
call backs in struct kgdb_arch.
Signed-off-by: NDongdong Deng <dongdong.deng@windriver.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

DBG_MAX_REG_NUM incorrectly had the number of indices in the GDB regs
array rather than the number of registers, leading to an oops when the
"rd" command is used in KDB.

Cc: stable@kernel.org
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

Selects HAVE_C_RECORDMCOUNT to use the C version of the recordmcount
intead of the old Perl Version of recordmcount.
Signed-off-by: NWu Zhangjin <wuzhangjin@gmail.com>
LKML-Reference: <bb99009a9ac79d3f55a8c8bf1c8bd2bc0e1f160e.1288176026.git.wuzhangjin@gmail.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The TASK_SIZE macro should reflect the size of a user process virtual
address space.  Previously for 64-bit kernels, this was not the case.
The immediate cause of pain was in
hugetlbfs/inode.c:hugetlb_get_unmapped_area() where 32-bit processes
trying to mmap a huge page would be served a page with an address
outside of the 32-bit address range.  But there are other uses of
TASK_SIZE in the kernel as well that would like an accurate value.

The new definition is nice because it now makes TASK_SIZE and
TASK_SIZE_OF() yield the same value for any given process.

For 32-bit kernels there should be no change, although I did factor
out some code in asm/processor.h that became identical for the 32-bit and
64-bit cases.

__UA_LIMIT is now set to ~((1 << SEGBITS) - 1) for 64-bit kernels.
This should eliminate the possibility of getting a
AddressErrorException in the kernel for addresses that pass the
access_ok() test.

With the patch applied, I can still run o32, n32 and n64 processes,
and have an o32 shell fork/exec both n32 and n64 processes.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1701/

Some MIPS32R1 processors implement UserLocal (RDHWR $29) to accelerate
programs that make extensive use of thread-local storage.  Therefore,
setting up the HWRENA register should not depend on cpu_has_mips_r2.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org

On many of the newer MIPS32 cores, CP0 CONFIG2 bit 12 (L2B) indicates
that the L2 cache is disabled and therefore Linux should not attempt
to use it.

[Ralf: Moved the code added by Kevin's original patch into a separate
function that can easily be replaced for platforms that need more a
different probe.]
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Cc: linux-mips@linux-mips.org>
Cc: <linux-kernel@vger.kernel.org>
Patchwork: https://patchwork.linux-mips.org/patch/1723/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Cc: mbizon@freebox.fr
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Tested-by: NFlorian Fainelli <ffainelli@freebox.fr>
Patchwork: https://patchwork.linux-mips.org/patch/1708/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org

[v2: add "VIPER" marketing name for BMIPS4350]

Add processor feature definitions for BMIPS3300, BMIPS4350, BMIPS4380,
and BMIPS5000.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Cc: mbizon@freebox.fr
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Tested-by: NFlorian Fainelli <ffainelli@freebox.fr>
Patchwork: https://patchwork.linux-mips.org/patch/1716/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org

BMIPS processor cores are used in 50+ different chipsets spread across
5+ product lines.  In many cases the chipsets do not share the same
peripheral register layouts, the same register blocks, the same
interrupt controllers, the same memory maps, or much of anything else.

But, across radically different SoCs that share nothing more than the
same BMIPS CPU, a few things are still mostly constant:

SMP operations
Access to performance counters
DMA cache coherency quirks
Cache and memory bus configuration

So, it makes sense to treat each BMIPS processor type as a generic
"building block," rather than tying it to a specific SoC.  This makes it
easier to support a large number of BMIPS-based chipsets without
unnecessary duplication of code, and provides the infrastructure needed
to support BMIPS-proprietary features.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Cc: mbizon@freebox.fr
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Tested-by: NFlorian Fainelli <ffainelli@freebox.fr>
Patchwork: https://patchwork.linux-mips.org/patch/1706/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org

This patch adds the mipsxx Perf-events support based on the skeleton.
Generic hardware events and cache events are now fully implemented for
the 24K/34K/74K/1004K cores. To support other cores in mipsxx (such as
R10000/SB1), the generic hardware event tables and cache event tables
need to be filled out. To support other CPUs which have different PMU
than mipsxx, such as RM9000 and LOONGSON2, the additional files
perf_event_$cpu.c need to be created.

Raw event is an important part of Perf-events. It helps the user collect
performance data for events that are not listed as the generic hardware
events and cache events but ARE supported by the CPU's PMU.

This patch also adds this feature for mipsxx 24K/34K/74K/1004K. For how to
use it, please refer to processor core software user's manual and the
comments for mipsxx_pmu_map_raw_event() for more details.

Please note that this is a "precise" implementation, which means the
kernel will check whether the requested raw events are supported by this
CPU and which hardware counters can be assigned for them.

To test the functionality of Perf-event, you may want to compile the tool
"perf" for your MIPS platform. You can refer to the following URL:
http://www.linux-mips.org/archives/linux-mips/2010-10/msg00126.html

You also need to customize the CFLAGS and LDFLAGS in tools/perf/Makefile
for your libs, includes, etc.

In case you encounter the boot failure in SMVP kernel on multi-threading
CPUs, you may take a look at:
http://www.linux-mips.org/git?p=linux-mti.git;a=commitdiff;h=5460815027d802697b879644c74f0e8365254020Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Cc: ddaney@caviumnetworks.com
Cc: matt@console-pimps.org
Patchwork: https://patchwork.linux-mips.org/patch/1689/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/kernel/perf_event_mipsxx.c

Adds callchain support for MIPS Perf-events. For more info on this feature,
please refer to tools/perf/Documentation/perf-report.txt and
tools/perf/design.txt.

Currently userspace callchain data is not recorded, because we do not have
a safe way to do this.
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Cc: matt@console-pimps.org
Patchwork: https://patchwork.linux-mips.org/patch/1690/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This patch provides the skeleton of the HW perf event support. To enable
this feature, we can not choose the SMTC kernel; Oprofile should be
disabled; kernel performance events be selected. Then we can enable it in
Kernel type menu.

Oprofile for MIPS platforms initializes irq at arch init time. Currently
we do not change this logic to allow PMU reservation.

If a platform has EIC, we can use the irq base and perf counter irq offset
defines for the interrupt controller in specific init_hw_perf_events().

Based on this skeleton patch, the 3 different kinds of MIPS PMU, namely,
mipsxx/loongson2/rm9000, can be supported by adding corresponding lower
level C files at the bottom. The suggested names of these files are
perf_event_mipsxx.c/perf_event_loongson2.c/perf_event_rm9000.c. So, for
example, we can do this by adding "#include perf_event_mipsxx.c" at the
bottom of perf_event.c.

In addition, PMUs with 64bit counters are also considered in this patch.
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Cc: ddaney@caviumnetworks.com
Cc: matt@console-pimps.org
Patchwork: https://patchwork.linux-mips.org/patch/1688/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Software events are required as part of the measurable stuff by the
Linux performance counter subsystem. Here is the list of events added by
this patch:
PERF_COUNT_SW_PAGE_FAULTS
PERF_COUNT_SW_PAGE_FAULTS_MIN
PERF_COUNT_SW_PAGE_FAULTS_MAJ
PERF_COUNT_SW_ALIGNMENT_FAULTS
PERF_COUNT_SW_EMULATION_FAULTS
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Acked-by: NDavid Daney <ddaney@caviumnetworks.com>
Reviewed-by: NMatt Fleming <matt@console-pimps.org>
Patchwork: https://patchwork.linux-mips.org/patch/1686/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Perf-events is now using local_t helper functions internally. There is a
use of local_xchg(). On MIPS, this is defined to xchg_local() which is
missing in asm/system.h. This patch re-defines local_xchg() in asm/local.h
to atomic_long_xchg(). Then Perf-events can pass the build.
Signed-off-by: NDeng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Cc: ddaney@caviumnetworks.com
Cc: matt@console-pimps.org
Patchwork: https://patchwork.linux-mips.org/patch/1687/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add support for Titan TNETV1050,1055,1056,1060 variants. This SoC is almost
completely identical to AR7 except on a few points:
- a second bank of gpios is available
- vlynq0 on titan is vlynq1 on ar7
- different PHY addresses for cpmac0

This SoC can be found on commercial products like the Linksys WRTP54G

Original patch by Xin with improvments by Florian.
Signed-off-by: NXin Zhen <xlonestar2000@aim.com>
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/1563/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

---

In order to detect the Titan variant, we must initialize GPIOs earlier since
detection relies on some GPIO values to be set.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/1562/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

---

Declare that OCTEON reference boards have both OHCI and EHCI.

Add platform devices for the corresponding hardware.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1676/Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The EHCI and OHCI blocks connection to the I/O bus is controlled by
these registers.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1674/Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 create mode 100644 arch/mips/include/asm/octeon/cvmx-uctlx-defs.h

The CN63XXP1 needs a couple of workarounds to ensure memory is not written
in unexpected ways.

All PREF with hints in the range 0-4,6-24 are replaced with PREF 28.  We
pass a flag to the assembler to cover compiler generated code, and patch
uasm for the dynamically generated code.

The write buffer threshold is reduced to 4.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1672/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The I2C and UARTS are clocked by the I/O clock, use its rate for these
devices.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1670/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Starting with cn63xx Octeon I/O blocks are clocked at a different rate
than the CPU.  Add a new function octeon_get_io_clock_rate() that
yields the I/O clock rate.

Also rearrange octeon_get_clock_rate() to get the value from the saved
sysinfo structure.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1671/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We can run with any simulator clock rate.  Get rid of the code
overriding it to 6MHz.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1669/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The per-CPU clocks are synchronized from IPD_CLK_COUNT, on cn63XX it must
be scaled by the clock frequency ratio.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1667/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>