We need to handle numa pte via the slow path
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

One OPAL call and one device tree property needed byte swapping.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

OPAL defines opal_msg as a big endian struct so we have to
byte swap it on little endian builds.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The firmware can notify us when new input data is available, so
let's make sure we wakeup the HVC thread in that case.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

opal_notifier_register() is missing a pending "unregister" variant
and should be exposed to modules.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Turn them on at the same time as we allow MSR_IR/DR in the paca
kernel MSR, ie, after the MMU has been setup enough to be able
to handle relocated access to the linear mapping.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

If we take an interrupt such as a trap caused by a BUG_ON before the
MMU has been setup, the interrupt handlers try to enable virutal mode
and cause a recursive crash, making the original problem very hard
to debug.

This fixes it by adjusting the "kernel_msr" value in the PACA so that
it only has MSR_IR and MSR_DR (translation for instruction and data)
set after the MMU has been initialized for the processor.

We may still not have a console yet but at least we don't get into
a recursive fault (and early debug console or memory dump via JTAG
of the kernel buffer *will* give us the proper error).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

All our cpu feature updates were done for every CPU in the device-tree,
thus overwriting the cputable bits over and over again. Instead do them
only for the boot CPU.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Move the definition to setup-common.c and set the init value
to -1 on both 32 and 64-bit (it was 0 on 64-bit).

Additionally add a check to prom.c to garantee that the init
value has been udpated after the DT scan.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

For historical reasons that code was under #ifdef CONFIG_PPC_PSERIES
but it applies equally to all 64-bit platforms.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We can't take an IRQ when we're about to do a trechkpt as our GPR state is set
to user GPR values.

We've hit this when running some IBM Java stress tests in the lab resulting in
the following dump:

  cpu 0x3f: Vector: 700 (Program Check) at [c000000007eb3d40]
      pc: c000000000050074: restore_gprs+0xc0/0x148
      lr: 00000000b52a8184
      sp: ac57d360
     msr: 8000000100201030
    current = 0xc00000002c500000
    paca    = 0xc000000007dbfc00     softe: 0     irq_happened: 0x00
      pid   = 34535, comm = Pooled Thread #
  R00 = 00000000b52a8184   R16 = 00000000b3e48fda
  R01 = 00000000ac57d360   R17 = 00000000ade79bd8
  R02 = 00000000ac586930   R18 = 000000000fac9bcc
  R03 = 00000000ade60000   R19 = 00000000ac57f930
  R04 = 00000000f6624918   R20 = 00000000ade79be8
  R05 = 00000000f663f238   R21 = 00000000ac218a54
  R06 = 0000000000000002   R22 = 000000000f956280
  R07 = 0000000000000008   R23 = 000000000000007e
  R08 = 000000000000000a   R24 = 000000000000000c
  R09 = 00000000b6e69160   R25 = 00000000b424cf00
  R10 = 0000000000000181   R26 = 00000000f66256d4
  R11 = 000000000f365ec0   R27 = 00000000b6fdcdd0
  R12 = 00000000f66400f0   R28 = 0000000000000001
  R13 = 00000000ada71900   R29 = 00000000ade5a300
  R14 = 00000000ac2185a8   R30 = 00000000f663f238
  R15 = 0000000000000004   R31 = 00000000f6624918
  pc  = c000000000050074 restore_gprs+0xc0/0x148
  cfar= c00000000004fe28 dont_restore_vec+0x1c/0x1a4
  lr  = 00000000b52a8184
  msr = 8000000100201030   cr  = 24804888
  ctr = 0000000000000000   xer = 0000000000000000   trap =  700

This moves tm_recheckpoint to a C function and moves the tm_restore_sprs into
that function.  It then adds IRQ disabling over the trechkpt critical section.
It also sets the TEXASR FS in the signals code to ensure this is never set now
that we explictly write the TM sprs in tm_recheckpoint.
Signed-off-by: NMichael Neuling <mikey@neuling.org>
cc: stable@vger.kernel.org
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The current kernel code assumes big endian and parses RTAS events all
wrong. The most visible effect is that we cannot honor EPOW events,
meaning, for example, we cannot shut down a guest properly from the
hypervisor.

This new patch is largely inspired by Nathan's work: we get rid of all
the bit fields in the RTAS event structures (even the unused ones, for
consistency). We also introduce endian safe accessors for the fields used
by the kernel (trivial rtas_error_type() accessor added for consistency).

Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NGreg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The emulated (CONFIG_MATH_EMULATION_FULL)
PowerPC Floating Point instruction mtfsf
does not correctly copy bits from its source
register to the Floating Point Status and Register (FPSCR).

The error is in the preparation of the mask used to
select the bits to be copied from the source to the FPSCR.

Execution of the mtfsf instruction does not produce the same
results on a MPC8548 platform (emulated floating point)
as on MPC7410 or 440EP platforms (hardware floating point).

This error has been detected using a Freescale MPC8548
based platform and the patch below tested using that platform.

The patch is based on the patch(es) provided by
Gabriel Paubert and analysis by Gabriel, James Yang and David Laight.
Signed-off-by: NStephen Chivers <schivers@csc.com>
Signed-off-by: NGabriel Paubert <paubert@iram.es>
Tested-by: NStephen Chivers <schivers@csc.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Pull arch/tile updates from Chris Metcalf:
 "These fix a few stray build issues seen in linux-next, and also add
  the minimal required support for perf to tilegx"

* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
  arch/tile: remove unused variable 'devcap'
  tile: Fix vDSO compilation issue with allyesconfig
  perf tools: Allow building for tile
  tile/perf: Support perf_events on tilegx and tilepro
  tile: Enable NMIs on return from handle_nmi() without errors
  tile: Add support for handling PMC hardware
  tile: don't use __get_cpu_var() with structure-typed arguments
  tile: avoid overflow in ns2cycles

Pull device mapper changes from Mike Snitzer:

 - Fix dm-cache corruption caused by discard_block_size > cache_block_size

 - Fix a lock-inversion detected by LOCKDEP in dm-cache

 - Fix a dangling bio bug in the dm-thinp target's process_deferred_bios
   error path

 - Fix corruption due to non-atomic transaction commit which allowed a
   metadata superblock to be written before all other metadata was
   successfully written -- this is common to all targets that use the
   persistent-data library's transaction manager (dm-thinp, dm-cache and
   dm-era).

 - Various small cleanups in the DM core

 - Add the dm-era target which is useful for keeping track of which
   blocks were written within a user defined period of time called an
   'era'.  Use cases include tracking changed blocks for backup
   software, and partially invalidating the contents of a cache to
   restore cache coherency after rolling back a vendor snapshot.

 - Improve the on-disk layout of multithreaded writes to the
   dm-thin-pool by splitting the pool's deferred bio list to be a
   per-thin device list and then sorting that list using an rb_tree.
   The subsequent read throughput of the data written via multiple
   threads improved by ~70%.

 - Simplify the multipath target's handling of queuing IO by pushing
   requests back to the request queue rather than queueing the IO
   internally.

* tag 'dm-3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (24 commits)
  dm cache: fix a lock-inversion
  dm thin: sort the per thin deferred bios using an rb_tree
  dm thin: use per thin device deferred bio lists
  dm thin: simplify pool_is_congested
  dm thin: fix dangling bio in process_deferred_bios error path
  dm mpath: print more useful warnings in multipath_message()
  dm-mpath: do not activate failed paths
  dm mpath: remove extra nesting in map function
  dm mpath: remove map_io()
  dm mpath: reduce memory pressure when requeuing
  dm mpath: remove process_queued_ios()
  dm mpath: push back requests instead of queueing
  dm table: add dm_table_run_md_queue_async
  dm mpath: do not call pg_init when it is already running
  dm: use RCU_INIT_POINTER instead of rcu_assign_pointer in __unbind
  dm: stop using bi_private
  dm: remove dm_get_mapinfo
  dm: make dm_table_alloc_md_mempools static
  dm: take care to copy the space map roots before locking the superblock
  dm transaction manager: fix corruption due to non-atomic transaction commit
  ...

Pull IOMMU upates from Joerg Roedel:
 "This time a few more updates queued up.

   - Rework VT-d code to support ACPI devices

   - Improvements for memory and PCI hotplug support in the VT-d driver

   - Device-tree support for OMAP IOMMU

   - Convert OMAP IOMMU to use devm_* interfaces

   - Fixed PASID support for AMD IOMMU

   - Other random cleanups and fixes for OMAP, ARM-SMMU and SHMOBILE
     IOMMU

  Most of the changes are in the VT-d driver because some rework was
  necessary for better hotplug and ACPI device support"

* tag 'iommu-updates-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (75 commits)
  iommu/vt-d: Fix error handling in ANDD processing
  iommu/vt-d: returning free pointer in get_domain_for_dev()
  iommu/vt-d: Only call dmar_acpi_dev_scope_init() if DRHD units present
  iommu/vt-d: Check for NULL pointer in dmar_acpi_dev_scope_init()
  iommu/amd: Fix logic to determine and checking max PASID
  iommu/vt-d: Include ACPI devices in iommu=pt
  iommu/vt-d: Finally enable translation for non-PCI devices
  iommu/vt-d: Remove to_pci_dev() in intel_map_page()
  iommu/vt-d: Remove pdev from intel_iommu_attach_device()
  iommu/vt-d: Remove pdev from iommu_no_mapping()
  iommu/vt-d: Make domain_add_dev_info() take struct device
  iommu/vt-d: Make domain_remove_one_dev_info() take struct device
  iommu/vt-d: Rename 'hwdev' variables to 'dev' now that that's the norm
  iommu/vt-d: Remove some pointless to_pci_dev() calls
  iommu/vt-d: Make get_valid_domain_for_dev() take struct device
  iommu/vt-d: Make iommu_should_identity_map() take struct device
  iommu/vt-d: Handle RMRRs for non-PCI devices
  iommu/vt-d: Make get_domain_for_dev() take struct device
  iommu/vt-d: Make domain_context_mapp{ed,ing}() take struct device
  iommu/vt-d: Make device_to_iommu() cope with non-PCI devices
  ...

Pull hwmon updates from Jean Delvare:
 "This includes a number of driver conversions to
  devm_hwmon_device_register_with_groups, a few cleanups, and
  support for the ITE IT8623E"

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  hwmon: (it87) Add support for IT8623E
  hwmon: (it87) Fix IT8603E define name
  hwmon: (lm90) Convert to use hwmon_device_register_with_groups
  hwmon: (lm90) Create all sysfs groups in one call
  hwmon: (lm90) Always use the dev variable in the probe function
  hwmon: (lm90) Create most optional attributes with sysfs_create_group
  hwmon: Avoid initializing the same field twice
  hwmon: (pc87360) Avoid initializing the same field twice
  hwmon: (lm80) Convert to use devm_hwmon_device_register_with_groups
  hwmon: (adm1021) Convert to use devm_hwmon_device_register_with_groups
  hwmon: (lm63) Avoid initializing the same field twice
  hwmon: (lm63) Convert to use devm_hwmon_device_register_with_groups
  hwmon: (lm63) Create all sysfs groups in one call
  hwmon: (lm63) Introduce 'dev' variable to point to client->dev
  hwmon: (lm63) Add additional sysfs group for temp2_type attribute
  hwmon: (f71805f) Fix author's address

Pull clock framework changes from Mike Turquette:
 "The clock framework changes for 3.15 look similar to past pull
  requests.  Mostly clock driver updates, more Device Tree support in
  the form of common functions useful across platforms and a handful of
  features and fixes to the framework core"

* tag 'clk-for-linus-3.15' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
  clk: shmobile: fix setting paretn clock rate
  clk: shmobile: rcar-gen2: fix lb/sd0/sd1/sdh clock parent to pll1
  clk: Fix minor errors in of_clk_init() function comments
  clk: reverse default clk provider initialization order in of_clk_init()
  clk: sirf: update copyright years to 2014
  clk: mmp: try to use closer one when do round rate
  clk: mmp: fix the wrong calculation formula
  clk: mmp: fix wrong mask when calculate denominator
  clk: st: Adds quadfs clock binding
  clk: st: Adds clockgen-vcc and clockgen-mux clock binding
  clk: st: Adds clockgen clock binding
  clk: st: Adds divmux and prediv clock binding
  clk: st: Support for A9 MUX clocks
  clk: st: Support for ClockGenA9/DDR/GPU
  clk: st: Support for QUADFS inside ClockGenB/C/D/E/F
  clk: st: Support for VCC-mux and MUX clocks
  clk: st: Support for PLLs inside ClockGenA(s)
  clk: st: Support for DIVMUX and PreDiv Clocks
  clk: support hardware-specific debugfs entries
  clk: s2mps11: Use of_get_child_by_name
  ...

Merge tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm

Pull pwm changes from Thierry Reding:
 "The legacy HAVE_PWM Kconfig symbol is finally being retired.  Thanks a
  lot to Sascha Hauer for doing that.

  Three new drivers are added: Freescale FTM, Cirrus Logic CLPS711X and
  Intel Low Power Subsystem.

  An assortment of fixes and cleanups rounds things off for this release
  cycle"

* tag 'pwm/for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
  pwm: pxa: Constify OF match table
  pwm: pxa: Fix typo "pwm" -> "PWM"
  Revert "pwm: pxa: Use of_match_ptr()"
  pwm: add support for Intel Low Power Subsystem PWM
  pwm: Add CLPS711X PWM support
  pwm: atmel: correct CDTY calculation
  pwm: atmel: Fix polarity handling
  Documentation: Add device tree bindings for Freescale FTM PWM.
  pwm: Add Freescale FTM PWM driver support
  pwm: pxa: Use of_match_ptr()
  pwm: samsung: Use SIMPLE_DEV_PM_OPS macro
  pwm: renesas-tpu: Add dependency on HAS_IOMEM
  pwm: Remove obsolete HAVE_PWM Kconfig symbol

Pull ARM SoC late cleanups from Arnd Bergmann:
 "These could not be part of the first cleanup branch, because they
  either came too late in the cycle, or they have dependencies on other
  branches.  Important changes are:

   - The integrator platform is almost multiplatform capable after some
     reorganization (Linus Walleij)
   - Minor cleanups on Zynq (Michal Simek)
   - Lots of changes for Exynos and other Samsung platforms, including
     further preparations for multiplatform support and the clocks
     bindings are rearranged"

* tag 'tags/cleanup2-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
  devicetree: fix newly added exynos sata bindings
  ARM: EXYNOS: Fix compilation error in cpuidle.c
  ARM: S5P64X0: Explicitly include linux/serial_s3c.h in mach/pm-core.h
  ARM: EXYNOS: Remove hardware.h file
  ARM: SAMSUNG: Remove hardware.h inclusion
  ARM: S3C24XX: Remove invalid code from hardware.h
  dt-bindings: clock: Move exynos-audss-clk.h to dt-bindings/clock
  ARM: dts: Keep some essential LDOs enabled for arndale-octa board
  ARM: dts: Disable MDMA1 node for arndale-octa board
  ARM: S3C64XX: Fix build for implicit serial_s3c.h inclusion
  serial: s3c: Fix build of header without serial_core.h preinclusion
  ARM: EXYNOS: Allow wake-up using GIC interrupts
  ARM: EXYNOS: Stop using legacy Samsung PM code
  ARM: EXYNOS: Remove PM initcalls and useless indirection
  ARM: EXYNOS: Fix abuse of CONFIG_PM
  ARM: SAMSUNG: Move s3c_pm_check_* prototypes to plat/pm-common.h
  ARM: SAMSUNG: Move common save/restore helpers to separate file
  ARM: SAMSUNG: Move Samsung PM debug code into separate file
  ARM: SAMSUNG: Consolidate PM debug functions
  ARM: SAMSUNG: Use debug_ll_addr() to get UART base address
  ...

Pull ARM SoC sh driver change from Arnd Bergmann:
 "The drivers/sh subdirectory used to get merged through the SH
  architecture tree, but things are in flux there and some of the
  drivers are shared with ARM shmobile, we have picked it up for the
  time being.

  There is only one trivial patch from Laurent Pinchart this time"

* tag 'sh-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  sh: intc: Enable driver compilation with COMPILE_TEST

Pull ARM SoC driver changes from Arnd Bergmann:
 "These changes are mostly for ARM specific device drivers that either
  don't have an upstream maintainer, or that had the maintainer ask us
  to pick up the changes to avoid conflicts.

  A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
  shmobile), aside from that, reset controllers for STi as well as a
  large rework of the Marvell Orion/EBU watchdog driver are notable"

* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
  Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
  Revert "net: stmmac: Add SOCFPGA glue driver"
  ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
  ARM: STi: Add reset controller support to mach-sti Kconfig
  drivers: reset: stih416: add softreset controller
  drivers: reset: stih415: add softreset controller
  drivers: reset: Reset controller driver for STiH416
  drivers: reset: Reset controller driver for STiH415
  drivers: reset: STi SoC system configuration reset controller support
  dts: socfpga: Add sysmgr node so the gmac can use to reference
  dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
  reset: Add optional resets and stubs
  ARM: shmobile: r7s72100: fix bus clock calculation
  Power: Reset: Generalize qnap-poweroff to work on Synology devices.
  dts: socfpga: Update clock entry to support multiple parents
  ARM: socfpga: Update socfpga_defconfig
  dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
  net: stmmac: Add SOCFPGA glue driver
  watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
  drivers: cci: Export CCI PMU revision
  ...

Pull ARM SoC device tree changes from Arnd Bergmann:
 "A large part of the arm-soc patches are nowadays DT changes, adding
  support for new SoCs, boards and devices without changing kernel
  source.  The plan is still to move the devicetree files out of the
  kernel tree and reduce the amount of churn going on here, but we keep
  finding reasons to delay doing that.

  Changes are really all over the place, with little sticking out
  particularly.  We have contributions from a total of 116 people in
  this branch.

  Unfortunately, the size of this branch also causes a significant
  number of conflicts at the moment, typically when subsystem
  maintainers merge patches that change the driver at the same time as
  the dts files.  In most cases this could be avoided because the dts
  changes are supposed to be compatible in both ways, and we are asking
  everyone to send ARM dts changes through our tree only"

* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
  dts: stmmac: Document the clocks property in the stmmac base document
  dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
  ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
  ARM: STi: stih416: Add support for the FSM Serial Flash Controller
  ARM: tegra: fix Dalmore pinctrl configuration
  ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
  ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
  ARM: dts: Build all keystone dt blobs
  ARM: dts: keystone: Fix control register range for clktsip
  ARM: dts: keystone: Fix domain register range for clkfftc1
  ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
  ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
  ARM: dts: bcm21664: Add device tree files.
  ARM: DT: bcm21664: Device tree bindings
  ARM: efm32: properly namespace i2c location property
  ARM: efm32: fix unit address part in USART2 device nodes' names
  ARM: mvebu: Enable NAND controller in Armada 385-DB
  ARM: mvebu: Add support for NAND controller in Armada 38x SoC
  ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
  ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
  ...

Pull ARM SoC board changes from Arnd Bergmann:
 "As we continue to replace board files with device tree descriptions,
  this part of the ARM support is getting smaller.  We have basically
  just defconfig changes here this time, and a significant number of
  Renesas shmobile changes, as Renesas is still in the process of
  deprecating board file support"

* tag 'boards-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (92 commits)
  ARM: enable fhandle in multi_v7_defconfig
  ARM: tegra: enable fhandle in tegra_defconfig
  ARM: update multi_v7_defconfig for Tegra
  ARM: add Marvell Dove and some drivers to multi_v7 defconfig
  ARM: fix duplicate symbols in multi_v5_defconfig
  ARM: pxa: add gpio keys information
  ARM: tegra: defconfig updates
  ARM: config: keystone: enable AEMIF/NAND support
  ARM: qcom: Enable basic support for Qualcomm platforms in multi_v7_defconfig
  ARM: kirkwood: Add HP T5325 devices to {multi|mvebu}_v5_defconfig
  ARM: config: Add mvebu_v5_defconfig
  ARM: config: Add a multi_v5_defconfig
  ARM: shmobile: r7s72100: update defconfig for I2C usage
  ARM: shmobile: Remove Lager DT reference legacy clock bits
  ARM: shmobile: Remove Koelsch DT reference legacy clock bits
  ARM: shmobile: Remove KZM9D board code
  ARM: mvebu: update defconfigs for Armada 375 and 38x
  ARM: dove: Enable watchdog support in the defconfig
  ARM: mvebu: Enable watchdog support in defconfig
  ARM: config: keystone: enable led support
  ...

Pull ARM SoC specific changes from Arnd Bergmann:
 "Lots of changes specific to one of the SoC families.  Some that stick
  out are:

   - mach-qcom gains new features, most importantly SMP support for the
     newer chips (Stephen Boyd, Rohit Vaswani)
   - mvebu gains support for three new SoCs: Armada 375, 380 and 385
     (Thomas Petazzoni and Free-electrons team)
   - SMP support for Rockchips (Heiko Stübner)
   - Lots of i.MX changes (Shawn Guo)
   - Added support for BCM5301x SoC (Hauke Mehrtens)
   - Multiplatform support for Marvell Kirkwood and Dove (Andrew Lunn
     and Sebastian Hesselbarth doing the final part of a long journey)
   - Unify davinci platforms and remove obsolete ones (Sekhar Nori, Arnd
     Bergmann)"

* tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (126 commits)
  ARM: sunxi: Select HAVE_ARM_ARCH_TIMER
  ARM: cache-tauros2: remove ARMv6 code
  ARM: mvebu: don't select CONFIG_NEON
  ARM: davinci: fix DT booting with default defconfig
  ARM: configs: bcm_defconfig: enable bcm590xx regulator support
  ARM: davinci: remove tnetv107x support
  MAINTAINERS: Update ARM STi maintainers
  ARM: restrict BCM_KONA_UART to ARCH_BCM_MOBILE
  ARM: bcm21664: Add board support.
  ARM: sunxi: Add the new watchog compatibles to the reboot code
  ARM: enable ARM_HAS_SG_CHAIN for multiplatform
  ARM: davinci: remove da8xx_omapl_defconfig
  ARM: davinci: da8xx: fix multiple watchdog device registration
  ARM: davinci: add da8xx specific configs to davinci_all_defconfig
  ARM: davinci: enable da8xx build concurrently with older devices
  ARM: BCM5301X: workaround suppress fault
  ARM: BCM5301X: add early debugging support
  ARM: BCM5301X: initial support for the BCM5301X/BCM470X SoCs with ARM CPU
  ARM: mach-bcm: Remove GENERIC_TIME
  ARM: shmobile: APMU: Fix warnings due to improper printk formats
  ...

Pull ARM SoC cleanups from Arnd Bergmann:
 "These cleanup patches are mainly move stuff around and should all be
  harmless.  They are mainly split out so that other branches can be
  based on top to avoid conflicts.

  Notable changes are:

   - We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
     longer used (Uwe Kleine-König)
   - The Qualcomm MSM platform is split out into legacy mach-msm and
     new-style mach-qcom, to allow easier maintainance of the new
     hardware support without regressions (Kumar Gala)
   - A rework of some of the Kconfig logic to simplify multiplatform
     support (Rob Herring)
   - Samsung Exynos gets closer to supporting multiplatform (Sachin
     Kamat and others)
   - mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
   - at91 gains some common clock framework support (Alexandre Belloni,
     Jean-Jacques Hiblot and other French people)"

* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
  ARM: hisi: select HAVE_ARM_SCU only for SMP
  ARM: efm32: allow uncompress debug output
  ARM: prima2: build reset code standalone
  ARM: at91: add PWM clock
  ARM: at91: move sam9261 SoC to common clk
  ARM: at91: prepare common clk transition for sam9261 SoC
  ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
  ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
  ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
  ARM: at91: dt: Add at91sam9261 dt SoC support
  ARM: at91: switch sam9rl to common clock framework
  ARM: at91/dt: define main clk frequency of at91sam9rlek
  ARM: at91/dt: define at91sam9rl clocks
  ARM: at91: prepare common clk transition for sam9rl SoCs
  ARM: at91: prepare sam9 dt boards transition to common clk
  ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
  ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
  ARM: at91: Add at91sam9rl DT SoC support
  ARM: at91: prepare at91sam9rl DT transition
  ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
  ...

Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
 "Lots of isolated bug fixes that were not found to be important enough
  to be submitted before the merge window or backported into stable
  kernels.

  The vast majority of these came out of Arnd's randconfig testing and
  just prevents running into build-time bugs in configurations that we
  do not care about in practice"

* tag 'fixes-non-critical-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
  ARM: at91: fix a typo
  ARM: moxart: fix CPU selection
  ARM: tegra: fix board DT pinmux setup
  ARM: nspire: Fix compiler warning
  IXP4xx: Fix DMA masks.
  Revert "ARM: ixp4xx: Make dma_set_coherent_mask common, correct implementation"
  IXP4xx: Fix Goramo Multilink GPIO conversion.
  Revert "ARM: ixp4xx: fix gpio rework"
  ARM: tegra: make debug_ll code build for ARMv6
  ARM: sunxi: fix build for THUMB2_KERNEL
  ARM: exynos: add missing include of linux/module.h
  ARM: exynos: fix l2x0 saved regs handling
  ARM: samsung: select CRC32 for SAMSUNG_PM_CHECK
  ARM: samsung: select ATAGS where necessary
  ARM: samsung: fix SAMSUNG_PM_DEBUG Kconfig logic
  ARM: samsung: allow serial driver to be disabled
  ARM: s5pv210: enable IDE support in MACH_TORBRECK
  ARM: s5p64x0: fix building with only one soc type
  ARM: s3c64xx: select power domains only when used
  ARM: s3c64xx: MACH_SMDK6400 needs HSMMC1
  ...

Pull ARM changes from Russell King:

 - Perf updates from Will Deacon:
   - Support for Qualcomm Krait processors (run perf on your phone!)
   - Support for Cortex-A12 (run perf stat on your FPGA!)
   - Support for perf_sample_event_took, allowing us to automatically decrease
     the sample rate if we can't handle the PMU interrupts quickly enough
     (run perf record on your FPGA!).

 - Basic uprobes support from David Long:
     This patch series adds basic uprobes support to ARM. It is based on
     patches developed earlier by Rabin Vincent. That approach of adding
     hooks into the kprobes instruction parsing code was not well received.
     This approach separates the ARM instruction parsing code in kprobes out
     into a separate set of functions which can be used by both kprobes and
     uprobes. Both kprobes and uprobes then provide their own semantic action
     tables to process the results of the parsing.

 - ARMv7M (microcontroller) updates from Uwe Kleine-König

 - OMAP DMA updates (recently added Vinod's Ack even though they've been
   sitting in linux-next for a few months) to reduce the reliance of
   omap-dma on the code in arch/arm.

 - SA11x0 changes from Dmitry Eremin-Solenikov and Alexander Shiyan

 - Support for Cortex-A12 CPU

 - Align support for ARMv6 with ARMv7 so they can cooperate better in a
   single zImage.

 - Addition of first AT_HWCAP2 feature bits for ARMv8 crypto support.

 - Removal of IRQ_DISABLED from various ARM files

 - Improved efficiency of virt_to_page() for single zImage

 - Patch from Ulf Hansson to permit runtime PM callbacks to be available for
   AMBA devices for suspend/resume as well.

 - Finally kill asm/system.h on ARM.

* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (89 commits)
  dmaengine: omap-dma: more consolidation of CCR register setup
  dmaengine: omap-dma: move IRQ handling to omap-dma
  dmaengine: omap-dma: move register read/writes into omap-dma.c
  ARM: omap: dma: get rid of 'p' allocation and clean up
  ARM: omap: move dma channel allocation into plat-omap code
  ARM: omap: dma: get rid of errata global
  ARM: omap: clean up DMA register accesses
  ARM: omap: remove almost-const variables
  ARM: omap: remove references to disable_irq_lch
  dmaengine: omap-dma: cleanup errata 3.3 handling
  dmaengine: omap-dma: provide register read/write functions
  dmaengine: omap-dma: use cached CCR value when enabling DMA
  dmaengine: omap-dma: move barrier to omap_dma_start_desc()
  dmaengine: omap-dma: move clnk_ctrl setting to preparation functions
  dmaengine: omap-dma: improve efficiency loading C.SA/C.EI/C.FI registers
  dmaengine: omap-dma: consolidate clearing channel status register
  dmaengine: omap-dma: move CCR buffering disable errata out of the fast path
  dmaengine: omap-dma: provide register definitions
  dmaengine: omap-dma: consolidate setup of CCR
  dmaengine: omap-dma: consolidate setup of CSDP
  ...

Pull Hexagon updates from Richard Kuo:
 "Mostly cleanups for compilation with allmodconfig and some other
  miscellaneous fixes"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rkuo/linux-hexagon-kernel:
  Hexagon: update CR year for elf.h
  Hexagon: remove SP macro
  Hexagon:  set ELF_EXEC_PAGESIZE to PAGE_SIZE
  Hexagon: set the e_flags in user regset view for core dumps
  Hexagon: fix atomic_set
  Hexagon: add screen_info for VGA_CONSOLE
  hexagon: correct type on pgd copy
  smp, hexagon: kill SMP single function call interrupt
  arch: hexagon: include: asm: add generic macro 'mmiowb' in "io.h"
  arch: hexagon: kernel: hexagon_ksyms.c: export related symbols which various modules need
  arch: hexagon: kernel: reset.c: use function pointer instead of function for pm_power_off and export it
  arch: hexagon: include: asm: add "vga.h" in Kbuild
  arch: hexagon: include: asm: Kbuild: add generic "serial.h" in Kbuild
  arch: hexagon: include: uapi: asm: setup.h add swith macro __KERNEL__
  arch: hexagon: include: asm: add prefix "hvm[ci]_" for all enum members in "hexagon_vm.h"
  arch: hexagon: Kconfig: add HAVE_DMA_ATTR in Kconfig and remove "linux/dma-mapping.h" from "asm/dma-mapping.h"
  arch: hexagon: kernel: add export symbol function __delay()
  hexagon: include: asm: kgdb: extend DBG_MAX_REG_NUM for "cs0/1"
  hexagon: kernel: kgdb: include related header for pass compiling.
  hexagon: kernel: remove useless variables 'dn', 'r' and 'err' in time_init_deferred() in "time.c"

Pull m68k fixes from Greg Ungerer:
 "Just a couple of fixes.  Clean up compile warnings by using correct
  types in function args, and clean out the removed CONFIG_MTD_PARTITIONS"

* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: fix arg types for outs* functions
  m68k : Kill CONFIG_MTD_PARTITIONS

Pull exynos media updates from Mauro Carvalho Chehab:
 "These are the remaining patches I have for the merge windows.  It
  basically adds a new sensor and adds the needed DT bits for it to
  work"

* 'topic/exynos' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
  [media] s5p-fimc: Remove reference to outdated macro
  [media] s5p-jpeg: Fix broken indentation in jpeg-regs.h
  [media] exynos4-is: Add the FIMC-IS ISP capture DMA driver
  [media] exynos4-is: Add support for asynchronous subdevices registration
  [media] exynos4-is: Add clock provider for the SCLK_CAM clock outputs
  [media] exynos4-is: Use external s5k6a3 sensor driver
  [media] V4L: s5c73m3: Add device tree support
  [media] V4L: Add driver for s5k6a3 image sensor
  [media] Documentation: devicetree: Update Samsung FIMC DT binding
  [media] Documentation: dt: Add binding documentation for S5C73M3 camera
  [media] Documentation: dt: Add binding documentation for S5K6A3 image sensor

Pull fbdev changes from Tomi Valkeinen:
 "Various fbdev fixes and improvements, but nothing big"

* tag 'fbdev-main-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (38 commits)
  fbdev: Make the switch from generic to native driver less alarming
  Video: atmel: avoid the id of fix screen info is overwritten
  video: imxfb: Add DT default contrast control register property.
  video: atmel_lcdfb: ensure the hardware is initialized with the correct mode
  fbdev: vesafb: add dev->remove() callback
  fbdev: efifb: add dev->remove() callback
  video: pxa3xx-gcu: switch to devres functions
  video: pxa3xx-gcu: provide an empty .open call
  video: pxa3xx-gcu: pass around struct device *
  video: pxa3xx-gcu: rename some symbols
  sisfb: fix 1280x720 resolution support
  video: fbdev: uvesafb: Remove impossible code path in uvesafb_init_info
  video: fbdev: uvesafb: Remove redundant NULL check in uvesafb_remove
  fbdev: FB_OPENCORES should depend on HAS_DMA
  OMAPDSS: convert pixel clock to common videomode style
  OMAPDSS: Remove unused get_context_loss_count support
  OMAPDSS: use DISPC register to detect context loss
  video: da8xx-fb: Use "SIMPLE_DEV_PM_OPS" macro
  video: imxfb: Convert to SIMPLE_DEV_PM_OPS
  video: imxfb: Resolve mismatch between backlight/contrast
  ...

Pull single ktest fix from Steven Rostedt:
 "This just contains a single update by Satoru Takeuchi, which adds
  CLOSE_CONSOLE_SIGNAL to the kvm.conf file, as the kvm guest requires a
  different signal than a normal console uses"

* tag 'ktest-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
  ktest: Set CLOSE_CONSOLE_SIGNAL in the kvm.conf

Pull /dev/random changes from Ted Ts'o:
 "A number of cleanups plus support for the RDSEED instruction, which
  will be showing up in Intel Broadwell CPU's"

* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random:
  random: Add arch_has_random[_seed]()
  random: If we have arch_get_random_seed*(), try it before blocking
  random: Use arch_get_random_seed*() at init time and once a second
  x86, random: Enable the RDSEED instruction
  random: use the architectural HWRNG for the SHA's IV in extract_buf()
  random: clarify bits/bytes in wakeup thresholds
  random: entropy_bytes is actually bits
  random: simplify accounting code
  random: tighten bound on random_read_wakeup_thresh
  random: forget lock in lockless accounting
  random: simplify accounting logic
  random: fix comment on "account"
  random: simplify loop in random_read
  random: fix description of get_random_bytes
  random: fix comment on proc_do_uuid
  random: fix typos / spelling errors in comments

Signed-off-by: NRichard Kuo <rkuo@codeaurora.org>

The SP/r29 macro wasn't used anywhere else and was causing conflicts
with another module, so just remove it.
Signed-off-by: NRichard Kuo <rkuo@codeaurora.org>

Signed-off-by: NRichard Kuo <rkuo@codeaurora.org>

Signed-off-by: NRichard Kuo <rkuo@codeaurora.org>

Normal writes in our our architecture don't invalidate lock
reservations.
Signed-off-by: NRichard Kuo <rkuo@codeaurora.org>

Signed-off-by: NRichard Kuo <rkuo@codeaurora.org>