Most revisions of the OMAP4 Blaze/SDP platform do not have
the EHCI signals routed by default. The pads are routed
for the alternate HSI functionality instead, and explicit
board modifications are needed to route the signals to
the USB PHY on the board.

Also, turning on the PHY connected to the EHCI port causes
a board reboot during bootup due to an unintended short
on the rails - this affects many initial revisions of the
board, and needs a minor board mod to fix (or as a
workaround, one should not attempt to power on the
USB PHY).

Given that these boards need explicit board mods to even
get EHCI working (separate from the accidental short above),
we should not attempt to enable EHCI by default.

So drop the EHCI support from the board files for the
Blaze/SDP platforms.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the mux framework APIs to explicitly configure
the MUSB pads. The MUSB controller in OMAP4 can use
either the old ULPI interface, or the new internal PHY.
Configure the pads accordingly.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Moved all the board specific internal PHY functions out of usb_musb.c file
as this file is shared between the OMAP2+ and AM35xx platforms.
There exists a file which has the functions specific to internal PHY
used for OMAP4 platform. Moved all phy specific functions to this file
and passing these functions through board data in the board file.
Signed-off-by: NHema HK <hemahk@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68knommu: set flow handler for secondary interrupt controller of 5249
  m68knommu: remove use of IRQ_FLG_LOCK from 68360 platform support
  m68knommu: fix dereference of port.tty
  m68knommu: add missing linker __modver section
  m68knommu: fix mis-named variable int set_irq_chip loop
  m68knommu: add optimize memmove() function
  m68k: remove arch specific non-optimized memcmp()
  m68knommu: fix use of un-defined _TIF_WORK_MASK
  m68knommu: Rename m548x_wdt.c to m54xx_wdt.c
  m68knommu: fix m548x_wdt.c compilation after headers renaming
  m68knommu: Remove dependencies on nonexistent M68KNOMMU

The secondary interrupt controller of the ColdFire 5249 code is not
setting the edge triggered flow handler. Set it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The m68knommu arch does not define or use IRQ_FLG_LOCK in its irq
subsystem. Remove obsolete use of it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The struct_tty associated with a port is now a direct pointer
from within the local private driver info struct. So fix all uses
of it.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Add missing linker section __modver to fix:

  LD      vmlinux
/usr/local/bin/../m68k-uclinux/bin/ld.real: error: no memory region specified for loadable section `__modver'
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Compiling for 68360 targets gives:

  CC      arch/m68knommu/platform/68360/ints.o
arch/m68knommu/platform/68360/ints.c: In function ‘init_IRQ’:
arch/m68knommu/platform/68360/ints.c:135:16: error: ‘irq’ undeclared (first use in this function)
arch/m68knommu/platform/68360/ints.c:135:16: note: each undeclared identifier is reported only once for each function it appears in

Fix variable name used.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

Add an m68k/coldfire optimized memmove() function for the m68knommu arch.
This is the same function as used by m68k. Simple speed tests show this
is faster once buffers are larger than 4 bytes, and significantly faster
on much larger buffers (4 times faster above about 100 bytes).

This also goes part of the way to fixing a regression caused by commit
ea61bc46 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memmove() fucntion
defined, since there was none in the m68knommu/lib functions.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>

The m68k arch implements its own memcmp() function. It is not optimized
in any way (it is the most strait forward coding of memcmp you can get).
Remove it and use the kernels standard memcmp() implementation.

This also goes part of the way to fixing a regression caused by commit
ea61bc46 ("m68k/m68knommu: merge MMU and
non-MMU string.h"), which breaks non-coldfire non-mmu builds (which is
the 68x328 and 68360 families). They currently have no memcmp() function
defined, since there is none in the m68knommu/lib functions.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>

* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
  drm/radeon/kms: hopefully fix pll issues for real (v3)
  drm/radeon/kms: add bounds checking to avivo pll algo
  drm: fix wrong usages of drm_device in DRM Developer's Guide
  drm/radeon/kms: fix a few more atombios endian issues
  drm/radeon/kms: improve 6xx/7xx CS error output
  drm/radeon/kms: check AA resolve registers on r300
  drm/radeon/kms: fix tracking of BLENDCNTL, COLOR_CHANNEL_MASK, and GB_Z on r300
  drm/radeon/kms: use linear aligned for evergreen/ni bo blits
  drm/radeon/kms: use linear aligned for 6xx/7xx bo blits
  drm/radeon: fix race between GPU reset and TTM delayed delete thread.
  drm/radeon/kms: evergreen/ni big endian fixes (v2)
  drm/radeon/kms: 6xx/7xx big endian fixes
  drm/radeon/kms: atombios big endian fixes
  drm/radeon: 6xx/7xx non-kms endian fixes
  drm/radeon/kms: optimize CS state checking for r100->r500
  drm: do not leak kernel addresses via /proc/dri/*/vma
  drm/radeon/kms: add connector table for mac g5 9600
  radeon mkregtable: Add missing fclose() calls
  drm/radeon/kms: fix interlaced modes on dce4+
  drm/radeon: fix memory debugging since d961db75
  ...

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  pci: use security_capable() when checking capablities during config space read

Transparent hugepages can only be created if rmap is fully
functional. So we must prevent hugepages to be created while
is_vma_temporary_stack() is true.

This also optmizes away some harmless but unnecessary setting of
khugepaged_scan.address and it switches some BUG_ON to VM_BUG_ON.
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Acked-by: NRik van Riel <riel@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI / Video: Probe for output switch method when searching video devices.
  ACPI / Wakeup: Enable button GPEs unconditionally during initialization
  ACPI / ACPICA: Avoid crashing if _PRW is defined for the root object
  ACPI: Fix acpi_os_read_memory() and acpi_os_write_memory() (v2)

* 'tools-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
  tools: turbostat: style updates
  tools: turbostat: fix bitwise and operand

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx: (21 commits)
  dmaengine: add slave-dma maintainer
  dma: ipu_idmac: do not lose valid received data in the irq handler
  dmaengine: imx-sdma: fix up param for the last BD in sdma_prep_slave_sg()
  dmaengine: imx-sdma: correct sdmac->status in sdma_handle_channel_loop()
  dmaengine: imx-sdma: return sdmac->status in sdma_tx_status()
  dmaengine: imx-sdma: set sdmac->status to DMA_ERROR in err_out of sdma_prep_slave_sg()
  dmaengine: imx-sdma: remove IMX_DMA_SG_LOOP handling in sdma_prep_slave_sg()
  dmaengine i.MX dma: initialize dma capabilities outside channel loop
  dmaengine i.MX DMA: do not initialize chan_id field
  dmaengine i.MX dma: check sg entries for valid addresses and lengths
  dmaengine i.MX dma: set maximum segment size for our device
  dmaengine i.MX SDMA: reserve channel 0 by not registering it
  dmaengine i.MX SDMA: initialize dma capabilities outside channel loop
  dmaengine i.MX SDMA: do not initialize chan_id field
  dmaengine i.MX sdma: check sg entries for valid addresses and lengths
  dmaengine i.MX sdma: set maximum segment size for our device
  DMA: PL08x: fix channel pausing to timeout rather than lockup
  DMA: PL08x: fix infinite wait when terminating transfers
  dmaengine: imx-sdma: fix inconsistent naming in sdma_assign_cookie()
  dmaengine: imx-sdma: propagate error in sdma_probe() instead of returning 0
  ...

* 'for-2.6.38' of git://linux-nfs.org/~bfields/linux:
  nfsd: break lease on unlink due to rename
  nfsd4: acquire only one lease per file
  nfsd4: modify fi_delegations under recall_lock
  nfsd4: remove unused deleg dprintk's.
  nfsd4: split lease setting into separate function
  nfsd4: fix leak on allocation error
  nfsd4: add helper function for lease setup
  nfsd4: split up nfsd_break_deleg_cb
  NFSD: memory corruption due to writing beyond the stat array
  NFSD: use nfserr for status after decode_cb_op_status
  nfsd: don't leak dentry count on mnt_want_write failure

Merge branches 'core-fixes-for-linus' and 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  Revert "lockdep, timer: Fix del_timer_sync() annotation"

* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  timer debug: Hide kernel addresses via %pK in /proc/timer_list

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: Fix text_poke_smp_batch() deadlock
  perf tools: Fix thread_map event synthesizing in top and record
  watchdog, nmi: Lower the severity of error messages
  ARM: oprofile: Fix backtraces in timer mode
  oprofile: Fix usage of CONFIG_HW_PERF_EVENTS for oprofile_perf_init and friends

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, dmi, debug: Log board name (when present) in dmesg/oops output
  x86, ioapic: Don't warn about non-existing IOAPICs if we have none
  x86: Fix mwait_usable section mismatch
  x86: Readd missing irq_to_desc() in fixup_irq()
  x86: Fix section mismatch in LAPIC initialization

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: matrix_keypad - increase the limit of rows and columns
  Input: wacom - fix error path in wacom_probe()
  Input: ads7846 - check proper condition when freeing gpio
  Revert "Input: do not pass injected events back to the originating handler"
  Input: sysrq - rework re-inject logic
  Input: serio - clear pending rescans after sysfs driver rebind
  Input: rotary_encoder - use proper irqflags
  Input: wacom_w8001 - report resolution to userland

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  get rid of nameidata_dentry_drop_rcu() calling nameidata_drop_rcu()
  drop out of RCU in return_reval
  split do_revalidate() into RCU and non-RCU cases
  in do_lookup() split RCU and non-RCU cases of need_revalidate
  nothing in do_follow_link() is going to see RCU

* git://git.kernel.org/pub/scm/linux/kernel/git/mason/btrfs-unstable:
  Btrfs: check return value of alloc_extent_map()
  Btrfs - Fix memory leak in btrfs_init_new_device()
  btrfs: prevent heap corruption in btrfs_ioctl_space_info()
  Btrfs: Fix balance panic
  Btrfs: don't release pages when we can't clear the uptodate bits
  Btrfs: fix page->private races

task_show_regs used to be a debugging aid in the early bringup days
of Linux on s390. /proc/<pid>/status is a world readable file, it
is not a good idea to show the registers of a process. The only
correct fix is to remove task_show_regs.
Reported-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reintroduces commit 47970b1b which was subsequently reverted
as f00eaeea.  The original change was broken and caused X startup
failures and generally made privileged processes incapable of reading
device dependent config space.  The normal capable() interface returns
true on success, but the LSM interface returns 0 on success.  This thinko
is now fixed in this patch, and has been confirmed to work properly.

So, once again...Eric Paris noted that commit de139a33 ("pci: check caps
from sysfs file open to read device dependent config space") caused the
capability check to bypass security modules and potentially auditing.
Rectify this by calling security_capable() when checking the open file's
capabilities for config space reads.
Reported-by: NEric Paris <eparis@redhat.com>
Tested-by: NDave Young <hidave.darkstar@gmail.com>
Acked-by: NJames Morris <jmorris@namei.org>
Cc: Dave Airlie <airlied@gmail.com>
Cc: Alex Riesen <raa.lkml@gmail.com>
Cc: Sedat Dilek <sedat.dilek@googlemail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Signed-off-by: NJames Morris <jmorris@namei.org>

can't happen anymore and didn't work right anyway
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

... thus killing the need to handle drop-from-RCU in d_revalidate()
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

fixing oopsen in lookup_one_len()
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

and use unlikely() instead of gotos, for fsck sake...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>

The "Type 2" SMBIOS record that contains Board Name is not
strictly required and may be absent in the SMBIOS on some
platforms.

( Please note that Type 2 is not listed in Table 3 in Sec 6.2
  ("Required Structures and Data") of the SMBIOS v2.7
  Specification. )

Use the Manufacturer Name (aka System Vendor) name.
Print Board Name only when it is present.

Before the fix:
  (i) dmesg output: DMI: /ProLiant DL380 G6, BIOS P62 01/29/2011
 (ii) oops output:  Pid: 2170, comm: bash Not tainted 2.6.38-rc4+ #3 /ProLiant DL380 G6

After the fix:
  (i) dmesg output: DMI: HP ProLiant DL380 G6, BIOS P62 01/29/2011
 (ii) oops output:  Pid: 2278, comm: bash Not tainted 2.6.38-rc4+ #4 HP ProLiant DL380 G6
Signed-off-by: NNaga Chumbalkar <nagananda.chumbalkar@hp.com>
Reviewed-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Cc: <stable@kernel.org> # .3x - good for debugging, please apply as far back as it applies cleanly
LKML-Reference: <20110214224423.2182.13929.sendpatchset@nchumbalkar.americas.hpqcorp.net>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

mp_find_ioapic() prints errors like:

    ERROR: Unable to locate IOAPIC for GSI 13

if it can't find the IOAPIC that manages that specific GSI. I
see errors like that at every boot of a laptop that apparently
doesn't have any IOAPICs.

But if there are no IOAPICs it doesn't seem to be an error that
none can be found. A solution that gets rid of this message is
to directly return if nr_ioapics (still) is zero. (But keep
returning -1 in that case, so nothing breaks from this change.)

The call chain that generates this error is:

pnpacpi_allocated_resource()
    case ACPI_RESOURCE_TYPE_IRQ:
        pnpacpi_parse_allocated_irqresource()
            acpi_get_override_irq()
                 mp_find_ioapic()
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

Merge branch 'urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/rric/oprofile into perf/urgent

The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.

v2: testing options

v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.

Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852
https://bugzilla.kernel.org/show_bug.cgi?id=24462
https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

Prevent divider overflow.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28932Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

A few wrong usages of drm_device, which should be drm_driver.
Signed-off-by: NXiao Jiang <jgq516@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>