These are only used in C/T demod attach functions, don't add any real
benefit (ie. line length savings) and in case of cxd28xx_attach aren't
even used consequently. Remove them.
Signed-off-by: NDaniel Scheller <d.scheller@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The tuning logic is broken with regards to status report:
it relies on a previously-cached value that may not be valid
if re-tuned.

Change the logic to always read the status.
Acked-by: NDaniel Scheller <d.scheller@gmx.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fix typo s/:/;/

Cc: Rob Herring <robh+dt@kernel.org>
Cc: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: NAkinobu Mita <akinobu.mita@gmail.com>
Acked-by: NRob Herring <robh@kernel.org>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

If set_fmt callback is called with format->width or format->height set to
zero and HACTIVE_CNT or VACTIVE_CNT bits (respectively) in chip are zero
we will divide by zero later in this callback when we try to calculate
HSC or VSC values.

Fix this by explicitly rejecting these values.
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

A 0b1100 value in 4 LSBs of "General Status 1" register (AFD_FMT_STAT) has
known meaning for CX2584x-series chips - it means that a SECAM signal is
currently detected by the chip.

Use this opportunity to also fix wrong binary values that were present
as comments attached to some entries in an array where
chip register -> V4L2 standard mappings are stored.
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Setting a burst size of "8" doesn't work for IMX219 with 8-bit bayer,
but a burst size of "16" does.  Fix this.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The complete handler walks all entities, expecting to find an imx
subdevice for each and every entity.

However, camera drivers such as smiapp can themselves contain multiple
entities, for which there will not be an imx subdevice.  This causes
imx_media_find_subdev_by_sd() to fail, making the imx capture system
unusable with such cameras.

Work around this by killing the error entirely, thereby allowing
the imx capture to be used with such cameras.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Acked-by: NSteve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

When the tuner was split from m88rs2000 the attach function is in wrong
place.

Move to dm04_lme2510_tuner to trap errors on failure and removing
a call to lme_coldreset.

Prevents driver starting up without any tuner connected.

Fixes to trap for ts2020 fail.
LME2510(C): FE Found M88RS2000
ts2020: probe of 0-0060 failed with error -11
...
LME2510(C): TUN Found RS2000 tuner
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Tested-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Warm start has no check as whether a genuine device has
connected and proceeds to next execution path.

Check device should read 0x47 at offset of 2 on USB descriptor read
and it is the amount requested of 6 bytes.

Fix for
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access as
Reported-by: NAndrey Konovalov <andreyknvl@google.com>
Signed-off-by: NMalcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As we're now using SPDX identifiers, add the proper SPDX,
better identifying the licenses whith apply to the source code.

As we're now using the short license, it doesn't make sense to
keep the original license text.

Also, fix MODULE_LICENSE to properly identify GPL v2
at the Siano's common driver. Some codes there are licensed
on GPL v2 or latter, while others are GPL v2 only. So,
in order to reflect the common license that applies to
everything, the module itself should be GPLv2 only.

While here, use the Kernel's coding style for the comments
with copyright info.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As we're now using SPDX identifiers, on the several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.

As we're now using the short license, it doesn't make sense to
keep the original license text.

Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As we're now using SPDX identifiers, on the several
RC keymap files I wrote, add the proper SPDX, identifying
the license I meant.

As we're now using the short license, it doesn't make sense to
keep the original license text.

Also, fix MODULE_LICENSE to identify GPL v2, as this is the
minimal license requirement for those modles.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As we're now using SPDX identifiers, on several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.

As we're now using the short license, it doesn't make sense to
keep the original license text.

Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Acked-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As we're now using SPDX identifiers, on the several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.

As we're now using the short license, it doesn't make sense to
keep the original license text.

Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As we're now using SPDX identifiers, on the several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.

As we're now using the short license, it doesn't make sense to
keep the original license text.

Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

According to the UVC specification, stream error events carry no data.
Fix a buffer overflow (that should be harmless given data alignment)
when reporting the stream error event by removing the data byte from the
message.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Some cameras post inaccurate frame where next frame data overlap
it. this results in screen flicker, and it need to be prevented.

So this patch marks the buffer error to discard the frame where
buffer overflow.
Signed-off-by: NBaoyou Xie <baoyou.xie@linaro.org>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

usb_endpoint_maxp() has an inline keyword and searches for bits[10:0]
by & operation with 0x7ff. So, we can remove the duplicate & operation
with 0x7ff.
Signed-off-by: NJaejoong Kim <climbbb.kim@gmail.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Microsoft HoloLense UVC sensor uses D3DFMT instead of FOURCC when
exposing formats. This adds support for D3DFMT_L8 as exposed from
the Acer Windows Mixed Reality Headset.
Signed-off-by: NNicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fix ptr_ret.cocci warnings:
drivers/media/platform/exynos4-is/fimc-lite.c:1465:1-3: WARNING: PTR_ERR_OR_ZERO can be used

Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR

Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: NVasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Move ptype (property type) initialization out of switch case
and save few lines of code.
Signed-off-by: NStanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

As of_node_full_name() now returns only the basename, the endpoint
information printed became useless:

    adv748x 4-0070: Endpoint endpoint on port 7
    adv748x 4-0070: Endpoint endpoint on port 8
    adv748x 4-0070: Endpoint endpoint on port 10
    adv748x 4-0070: Endpoint endpoint on port 11

Restore the old behavior by using "%pOF" instead:

    adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@7/endpoint on port 7
    adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@8/endpoint on port 8
    adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@10/endpoint on port 10
    adv748x 4-0070: Endpoint /soc/i2c@e66d8000/video-receiver@70/port@11/endpoint on port 11

Fixes: a7e4cfb0 ("of/fdt: only store the device node basename in full_name")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

timespec is generally deprecated because of the y2038 overflow.
In vivid, the usage is fine, since we are dealing with monotonic
timestamps, but we can also simplify the code by going to ktime_t.

Using ktime_divns() should be roughly as efficient as the old code,
since the constant 64-bit division gets turned into a multiplication
on modern platforms, and we save multiple 32-bit divisions that can be
expensive e.g. on ARMv7.
Tested-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The imx media driver passes around monotonic timestamps in the deprecated
'timespec' format. This is not a problem for the driver, as they won't
overflow, but moving to either timespec64 or ktime_t is preferred.

I'm picking ktime_t for simplicity here. frame_interval_monitor() is
the main function that changes, as it tries to compare a time interval
in microseconds. The algorithm slightly changes here, to avoid 64-bit
division. The code previously assumed that the error was at most 32-bit
worth of microseconds here, so I'm making the same assumption but add
an explicit test for it.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

solo6x10 correctly deals with time stamps and will never
suffer from overflows, but it uses the deprecated 'struct timespec'
type and 'ktime_get_ts()' interface to read the monotonic clock.

This changes it to use ktime_get_ts64() instead, so we can
eventually remove ktime_get_ts().
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NIsmael Luceno <ismael@iodev.co.uk>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Deblocking filter allows to reduce blocking artifacts and improve
visual quality. This is configurable via the V4L2 API but eventually
not applied to the encoder.

Note that alpha and beta deblocking values are 32-bit signed (-6;+6).
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Reviewed-by: NStanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

H264 entropy mode can be selected via V4L2 API but is eventually not
applied. Configure encoder with selected mode, CALVC (def) or CABAC.

Note that hw/firmware also expects a CABAC model configuration which
currently doesn't have existing V4L2 API control. For now, use model_0
which seems always supported and so the default one.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Reviewed-by: NStanimir Varbanov <stanimir.varbanov@linaro.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Check return value from call to devm_kzalloc() in order to prevent
a NULL pointer dereference.

This issue was detected with the help of Coccinelle.

Fixes: 4a5f8ae5 ("[media] davinci: vpif_capture: get subdevs from DT when available")
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This change resolves a new compile-time warning
when built as a loadable module:

WARNING: modpost: missing MODULE_LICENSE() in drivers/media/platform/tegra-cec/tegra_cec.o
see include/linux/module.h for more information

This adds the license as "GPL v2", which matches the header of the file.

MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: NJesse Chan <jc@linux.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This change resolves a new compile-time warning
when built as a loadable module:

WARNING: modpost: missing MODULE_LICENSE() in drivers/media/platform/soc_camera/soc_scale_crop.o
see include/linux/module.h for more information

This adds the license as "GPL", which matches the header of the file.

MODULE_DESCRIPTION and MODULE_AUTHOR are also added.
Signed-off-by: NJesse Chan <jc@linux.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This change resolves a new compile-time warning
when built as a loadable module:

WARNING: modpost: missing MODULE_LICENSE() in drivers/media/platform/mtk-vcodec/mtk-vcodec-common.o
see include/linux/module.h for more information

This adds the license as "GPL v2", which matches the header of the file.

MODULE_DESCRIPTION is also added.
Signed-off-by: NJesse Chan <jc@linux.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

There is no need to #define the license of the driver, just put it in
the MODULE_LICENSE() line directly as a text string.

This allows tools that check that the module license matches the source
code license to work properly, as there is no need to unwind the
unneeded dereference.

Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Johan Hovold <johan@kernel.org>
Cc: Davidlohr Bueso <dave@stgolabs.net>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Reported-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: NPhilippe Ombredanne <pombredanne@nexb.com>
Acked-by: NMauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

time_to_tm() takes a time_t value that overflows in 2038 on 32-bit
systems. time64_to_tm() doesn't have this problem, so let's use that in
combination with ktime_get_real_seconds() to read a 64-bit time
value.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The cam->buffers[] array has cam->num_frames elements so the > needs to
be changed to >= to avoid going beyond the end of the array.  The
->buffers[] array is allocated in cpia2_allocate_buffers() if you want
to confirm.

Fixes: ab33d507 ("V4L/DVB (3376): Add cpia2 camera support")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

According to i.MX VPU API Reference Manuals the MJPG video codec is
referenced to by number 7, not 3.

Also Philipp pointed out that this value is only meant to fill in
CMD_ENC_SEQ_COD_STD for encoding, only on i.MX53. It was never written
to any register, and even if defined correctly, wouldn't be needed
for i.MX6.

So avoid confusion and remove this definition.
Signed-off-by: NMartin Kepplinger <martink@posteo.de>
Acked-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Fix inconsistent IS_ERR and PTR_ERR in csi_link_validate.
The proper pointer to be passed as argument is sensor.

This issue was detected with the help of Coccinelle.
Reported-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

When the device is being unregistered disable the hardware, don't wait
until cec_delete_adapter is called as the hardware may have disappeared by
then. This would be the case for hotplugable devices.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Reported-by: NBård Eirik Winther <bwinther@cisco.com>
Tested-by: NBård Eirik Winther <bwinther@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Document what this op does.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Some devices can monitor the CEC pin using an interrupt, but you
only want to enable the interrupt if you actually switch to pin
monitoring mode.

So add a new op that is called when pin monitoring needs to be
switched on or off.

Also fix a small bug where the initial CEC pin event was sent
again when calling S_MODE twice with the same CEC_MODE_MONITOR_PIN
mode.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The firmware timestamp is an unsigned 32-bit value, but we copy it into
a signed 32-bit variable, so we can theoretically get an overflow in
the calculation when the timestamp is between 2038 and 2106.

This changes the temporary variable to time64_t and changes the deprecated
time_to_tm() over to time64_to_tm() accordingly.

There is still an overflow in y2106, but that is a limitation of the
firmware interface, not a kernel problem.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>