Remove the _INP definitions, they are all zero and also unused
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove the old S3C2410_GPJ as we will be moving to the new gpiolib
based driver code and these numbers will become invalid.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change s3c2410_gpio_setpin() and s3c2410_gpio_pullup() to use
the new s3c_ gpio configuration calls until all their users
are converted.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove the last s3c2410_gpio_pullup() users in arch/arm/mach-s3c2410

Note, since mach-h1940.c is setting output and a pull-up, the call
has vbeen chanerd to S3C_GPIO_PULL_NONE instead of S3C_GPIO_PULL_UP.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Move the mach-mini2440 to using the gpiolib API for GPIOS it
directly uses, and s3c_gpio calls for configuration.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add s3c_gpio_getcfg() and change anything using s3c2410_gpio_getcfg() to
use this instead.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary 1,2 and 4 bit configuration read calls for the new
gpio code to allow removal of the old s3c24xx gpio code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove s3c2410_gpio_getirq() as the only users is the pm code, and it
can be replicated by using gpio_to_irq().
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove the unused s3c2410_gpio_getpull()
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove the implementation of s3c2410_gpio_setcfg() as it should now be
functionally equivalent to s3c_gpio_cfgpin(), and add a wrapper for those
drivers that are still using this call.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The s3c_gpio_cfgpin() call should be functionally equivalent, so replace
the s3c2410_gpio_cfgpin() calls in the s3c24xx code with s3c_gpio_cfgpin
to allow moving away from a fixed GPIO number to register address mapping
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Start moving code that is using the old s3c2410_gpio API to using the
newer s3c_gpio variants by finding all the usages of s3c2410_gpio_pullup()
which disable the pin's pull up and replacing them.

 sed 's/s3c2410_gpio_pullup\(.*\), 1/s3c_gpio_cfgpull\1, S3C_GPIO_PULL_NONE/g'
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Start moving code that is using the old s3c2410_gpio API to using the
newer s3c_gpio variants by finding all the usages of s3c2410_gpio_pullup()
which disable the pin's pull up and replacing them.

sed 's/s3c2410_gpio_pullup\(.*\), 1/s3c_gpio_cfgpull\1, S3C_GPIO_PULL_NONE/g'
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change mach-vr1000.c to use gpiolib for gpio control.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change mach-bast .c to use gpiolib for the GPIO lines that are directly
manipulated by it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change mach-n30.c to use gpiolib for the GPIO lines that are directly
manipulated by it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change mach-qt2410.c to use gpiolib for the GPIO lines that are directly
manipulated by it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change  mach-h1940 to use the gpiolib calls instead of s3c2410_gpio
directly.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change mach-jive to use gpiolib for the GPIO lines that are directly
manipulated by it.

Note, we ignore any errors from gpio_request(), unlikely to see any.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Change the h1940-bluetooth driver to use gpiolib to set the output state
of GPH1.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the GPIO banks that are used on the S3C2443 and above to the
list of available GPIOS.

Currently we do not have any limit on the SoC GPIO, so these are
being registered whether the SoC has them or not. It is currently
up to the user not to try and use them.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add the necessary gpio configuration helper for the devices which
have a single-bit pull-up resistor disabled.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Add support for s3c_gpio_setcfg() and s3c_gpio_setpull() implementations
to get ready for removal of the specific code being used by s3c24xx.

Also rename the s3c_gpio_setcfg_s3c24xx_banka to s3c_gpio_setcfg_s3c24xx_a
as seen in the header file to correct a build warning.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

MUSB can supply upto 500mA such as, AM3517 and OMAP3EVM Rev >=E and thus
the 'power' field has to hold values above 255.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The switch to using GPIOLIB broke the sd/mmc card detection on the
RealView development boards if GPIO_PL061 was not selected.
This patch selects GPIO_PL061 if GPIOLIB is selected.
The sense of the return value from mmc_status has also changed
and is corrected.
Signed-off-by: NColin Tuckley <colin.tuckley@arm.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

They are not needed and add over 512 bytes to kernel data.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Old code from original patch contains beagle board pins that are
not available on the Devkit8000.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Change position of calling serial and ethernet initialization.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove include otg.h.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Replace wrong sdr_cke[01] with sdrc_cke[01].
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Devkit8000 uses the CUS package for OMAP3530.

This patch adds missing package selection for CUS and enables
CONFIG_MUX.

Replace whitespace with tab in Kconfig.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Replace wrong vdss_dsi with vdds_dsi.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

arch/arm/configs/n8x0_defconfig:1061:warning: override: reassigning to
symbol NILFS2_FS
Signed-off-by: NFrancisco Alecrim <francisco.alecrim@openbossa.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Corrected type of flash in output (OneNAND => NOR).
Removed whitespace after newline in output.
Removed double whitespace in output.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch fixes the McBSP4 base address for OMAP4
Signed-off-by: NBalaji T K <balajitk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Modern udev will not work with the CONFIG_SYSFS_DEPRECATED*=y options and
it seems also that the Maemo release works without when testing with the
Maemo 2.6.28 kernel.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Phonet is enabled by the commit bce54fed
and this duplicate gives a warning when doing make rx51_defconfig.
Signed-off-by: NJarkko Nikula <jhnikula@gmail.com>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If gpmc_t isn't given, we don't need to set timing for gpmc, or it will cause
a Oops.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The initialize of i2c subsystem will set pinmux, so it should be done
after the initialize of mux subsystem initialization.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

INT_34XX_BENCH_MPU_EMUL was defined twice, another is at Line 312.
Signed-off-by: NStanley.Miao <stanley.miao@windriver.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>