Based on BenH's earlier work, this is a new version of the EMAC driver
for the built-in ethernet found on PowerPC 4xx embedded CPUs.  The
same ASIC is also found in the Axon bridge chip.  This new version is
designed to work in the arch/powerpc tree, using the device tree to
probe the device, rather than the old and ugly arch/ppc OCP layer.

This driver is designed to sit alongside the old driver (that lies in
drivers/net/ibm_emac and this one in drivers/net/ibm_newemac).  The
old driver is left in place to support arch/ppc until arch/ppc itself
reaches its final demise (not too long now, with luck).

This driver still has a number of things that could do with cleaning
up, but I think they can be fixed up after merging.  Specifically:
	- Should be adjusted to properly use the dma mapping API.
Axon needs this.
	- Probe logic needs reworking, in conjuction with the general
probing code for of_platform devices.  The dependencies here between
EMAC, MAL, ZMII etc. make this complicated.  At present, it usually
works, because we initialize and register the sub-drivers before the
EMAC driver itself, and (being in driver code) runs after the devices
themselves have been instantiated from the device tree.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Since we are adding requirement for the PHYLIB for this driver, there should be a select for that

Cc: Robin Getz <robin.getz@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

 - add MDIO functions and register mdio bus
 - add phy abstraction layer (PAL) functions and use PAL API
 - test on STAMP537 board
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Blackfin EMAC driver: add power management interface and change the bf537mac_reset to bf537mac_disable
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Alex Landau writes in the forums:
 Previously, changing the MAC address (e.g. via ifconfig) resulted
 in a generic function to be called that only changed a variable in
 memory. This patch also updated the Blackfin MAC address registers
 to filter the correct new MAC.
Signed-off-by: NAlex Landau <lirsb@yahoo.com>
Signed-off-by: NMike Frysinger <michael.frysinger@analog.com>
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Update transceiver information in ethtool function
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

- Added set_mac_address driver entry point
- Copying permanent mac address to dev->perm_addr
- Incorporated following review comments from Jeff
     - Converted the macro to a function and removed call to memset
     - regarding function naming convention, for all callbacks and entry points
       will have 's2io_' prefix and helper functions will have 'do_s2io_' prefix.
Signed-off-by: NSreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Removed bimodal interrupt support - unused feature
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

[also, trim trailing whitespace]

- Changed kmalloc+memset to k[zc]alloc as per Mariusz's patch
  <m.kozlowski@tuxland.pl>
Signed-off-by: NSivakumar Subramani <sivakumar.subramani@neterion.com>
Signed-off-by: NRamkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

These have been superceded by the new ->get_sset_count() hook.
Signed-off-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is nicer than the MAC_FMT stuff.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the mac80211 based wireless drivers for the Intel
PRO/Wireless 3945ABG/BG Network Connection and Intel Wireless WiFi
Link AGN (4965) adapters.

[ Move driver into it's own directory -DaveM ]
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SSB is an SoC bus used in a number of embedded devices.  The most
well-known of these devices is probably the Linksys WRT54G, but there
are others as well.  The bus is also used internally on the BCM43xx
and BCM44xx devices from Broadcom.

This patch also includes support for SSB ID tables in modules, so
that SSB drivers can be loaded automatically.
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Return some useful information such as the maximum listen backlog and
the current listen backlog in the tcp_info structure and
INET_DIAG_INFO.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I proposed introducing a list_for_each_entry_continue_reverse macro
to be used in setup_net() when unrolling the failed ->init callback.

Here is the macro and some more cleanup in the setup_net() itself
to remove one variable from the stack :) The same thing is for the
cleanup_net() - the existing list_for_each_entry_reverse() is used.

Minor, but the code looks nicer.
Signed-off-by: NPavel Emelyanov <xemul@openvz.org>
Acked-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[ Ported to napi_struct changes... -DaveM ]
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJesse Huang <jesse@icplus.com.tw>
Signed-off-by: NStefan Lippers-Hollmann <s.l-h@gmx.de>
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ADD-IP spec requires AUTH. It is, in fact, dangerous without AUTH.
So, disable ADD-IP functionality if the peer claims to support
ADD-IP, but not AUTH.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add SCTP-AUTH API.  The API implemented here was
agreed to between implementors at the 9th SCTP Interop.
It will be documented in the next revision of the
SCTP socket API spec.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the receive path needed to process authenticated
chunks.  Add ability to process the AUTH chunk and handle edge cases
for authenticated COOKIE-ECHO as well.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

SCTP-AUTH, Section 6.2:

   Endpoints MUST send all requested chunks authenticated where this has
   been requested by the peer.  The other chunks MAY be sent
   authenticated or not.  If endpoint pair shared keys are used, one of
   them MUST be selected for authentication.

   To send chunks in an authenticated way, the sender MUST include these
   chunks after an AUTH chunk.  This means that a sender MUST bundle
   chunks in order to authenticate them.

   If the endpoint has no endpoint pair shared key for the peer, it MUST
   use Shared Key Identifier 0 with an empty endpoint pair shared key.
   If there are multiple endpoint shared keys the sender selects one and
   uses the corresponding Shared Key Identifier
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement processing for the CHUNKS, RANDOM, and HMAC parameters and
deal with how this parameters are effected by association restarts.
In particular, during unexpeted INIT processing, we need to reply with
parameters from the original INIT chunk.  Also, after restart, we need
to update the old association with new peer parameters and change the
association shared keys.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch initializes AUTH related members of the generic SCTP
structures and provides a way to enable/disable auth extension.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the internals operations of the AUTH, such as
key computation and storage.  It also adds necessary variables to
the SCTP data structures.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Background: RFC 4293 deprecates existing individual, named ICMP
type counters to be replaced with the ICMPMsgStatsTable. This table
includes entries for both IPv4 and IPv6, and requires counting of all
ICMP types, whether or not the machine implements the type.

These patches "remove" (but not really) the existing counters, and
replace them with the ICMPMsgStats tables for v4 and v6.
It includes the named counters in the /proc places they were, but gets the
values for them from the new tables. It also counts packets generated
from raw socket output (e.g., OutEchoes, MLD queries, RA's from
radvd, etc).

Changes:
1) create icmpmsg_statistics mib
2) create icmpv6msg_statistics mib
3) modify existing counters to use these
4) modify /proc/net/snmp to add "IcmpMsg" with all ICMP types
        listed by number for easy SNMP parsing
5) modify /proc/net/snmp printing for "Icmp" to get the named data
        from new counters.
Signed-off-by: NDavid L Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Background: RFC 4293 deprecates existing individual, named ICMP
type counters to be replaced with the ICMPMsgStatsTable. This table
includes entries for both IPv4 and IPv6, and requires counting of all
ICMP types, whether or not the machine implements the type.

These patches "remove" (but not really) the existing counters, and
replace them with the ICMPMsgStats tables for v4 and v6.
It includes the named counters in the /proc places they were, but gets the
values for them from the new tables. It also counts packets generated
from raw socket output (e.g., OutEchoes, MLD queries, RA's from
radvd, etc).

Changes:
1) create icmpmsg_statistics mib
2) create icmpv6msg_statistics mib
3) modify existing counters to use these
4) modify /proc/net/snmp to add "IcmpMsg" with all ICMP types
        listed by number for easy SNMP parsing
5) modify /proc/net/snmp printing for "Icmp" to get the named data
        from new counters.
[new to 2nd revision]
6) support per-interface ICMP stats
7) use common macro for per-device stat macros
Signed-off-by: NDavid L Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDenis Cheng <crquan@gmail.com>

Signed-off-by: NDenis Cheng <crquan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with the macro max provided by <linux/kernel.h>, so changed its name
to a more proper one: limit
Signed-off-by: NDenis Cheng <crquan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDenis Cheng <crquan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thanks for noticing the bug where csum_start is not updated
when the head room changes.

This patch fixes that.  It also moves the csum/ip_summed
copying into copy_skb_header so that skb_copy_expand gets
it too.  I've checked its callers and no one should be upset
by this.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I was looking at Patrick's fix to inet_diag and it occured
to me that we're using a pointer argument to return values
unnecessarily in netlink_run_queue.  Changing it to return
the value will allow the compiler to generate better code
since the value won't have to be memory-backed.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sctp_[rw]mem definitions should really be in protocol.c
since that is where they are initialized.  This also allows
one to build a kernel without sysctl support.
Signed-off-by: NVlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>