For the I80 interface, the video interrupt pending register(VIDINTCON1)
should be handled in fimd_irq_handler() and the video interrupt control
register(VIDINTCON0) should be handled in fimd_enable_vblank() and
fimd_disable_vblank() like RGB interface.
So this patch moves each set / unset routines into proper positions.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This function is valid only the SoC has SHADOWCON register
and it should be used together with fimd_enable_video_output()
to match the ENWIN_F bit in WINCON# and C#_EN_F bit in SHADOWCON.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This bit is used for video output and logic signal control.
So it is better for readability.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The C#_EN_F in SHADOWCON register is updated per frame.
So it should be protected by fimd_shadow_protect_win().
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

It's better to be checking whether triggerring in fimd_trigger function.
Also it will return if in triggerring on fimd_te_handler, then it can't
execute remain codes.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The exynos fimd provides video type selection bits from system register
but exynos3 series don't has it, so needs has_vtsel flag and we can
distinguish whether set video type selection bits.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

For providing VBLANK information, drm_handle_vblank() should
be called properly, but it is blocked by wait_vsync_event
condition which is set by manager_ops->wait_for_vblank().
So moves it out from wait_vsync_event routine.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>

The exynos_drm_crtc_dpms() waits until pended page flip
queue is empty, calls the drm_vblank_off() then calls
manager->ops->dpms() when mode is DRM_MODE_DPMS_OFF.
The fimd_dpms() is one of manager->ops->dpms()s and
finally calls fimd_window_suspend().
But there is no active window and vblank is already off
when it is called.
So addtional waiting vblank is not necessary any more.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch supports Exynos4415 SoC.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch replaces legacy functions
drm_plane_init() / drm_crtc_init() with
drm_universal_plane_init() and drm_crtc_init_with_planes().
It allows to replace fake primary plane with the real one.
Additionally the patch leaves cleanup of crtcs to core,
this way planes and crtcs are cleaned in correct order.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

From fimd driver and vidi driver, dev->irq_enabled and
dev->vblank_disable_allowed are set and also mixer needs them even if
missed. It's duplicated so set them when loads drm driver.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

To correctly disable hardware window during driver init, both enable bits
(WINCONx_ENWIN in WINCON and SHADOWCON_CHx_ENABLE in SHADOWCON) must be
cleared, otherwise hardware fails to re-enable such window later.

While touching this function, also temporarily disable ctx->suspended flag
to let fimd_wait_for_vblank function really to do its job.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Signed-off-by: NInki Dae <inki.dae@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>

Since 21bdd17b it is possible to have
multiple calls to MODULE_DEVICE_TABLE, so the patch can be
reverted to restore support for autoloading

Conflicts:
	drivers/gpu/drm/exynos/exynos_drm_fimd.c
	drivers/gpu/drm/exynos/exynos_drm_g2d.c
Signed-off-by: NSjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

To support MIPI command mode based I80 interface panel,
FIMD should do followings:
- Sets LCD I80 interface timings configuration.
- Uses "lcd_sys" as an IRQ resource and sets relevant IRQ configuration.
- Sets LCD block configuration for I80 interface.
- Sets ideal(pixel) clock is 2 times faster than the original one
  to generate frame done IRQ prior to the next TE signal.
- Implements trigger feature that transfers image data if there is page
  flip request, and implements TE handler to call trigger function.
Signed-off-by: NYoungJun Cho <yj44.cho@samsung.com>
Acked-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch disables non-enabled HW windows on applying
configuration, it will allow to clear windows enabled
by bootloader.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch makes sure that exynos drm framework handles deferred
probe case correctly.

Sub drivers could be probed before resources, clock, regulator,
phy or panel, are ready for them so we should make sure that exynos
drm core waits until all resources are ready and sub drivers are
probed correctly.

Chagelog v2:
- Make sure that exynos drm core tries to bind sub drivers only in case that
  they have a pair: crtc and encoder/connector components should be a pair.
- Remove unnecessary patch:
  drm/exynos: mipi-dsi: consider panel driver-deferred probe
- Return error type correctly.
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Acked-by: NKyungmin Park <kyungmin.park@samsung.com>

System hangs when FIMD registers are accessed to disable
hardware overlays. This is because of the clocks which are
not enabled before register access.

'Hardware overlay disable' is cleaned from the FIMD probe.
Signed-off-by: NRahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

In case of exynos, setting dma-burst to 16Word causes permanent
tearing for very small buffers, e.g. cursor buffer. Burst Mode
switching, which is based on overlay size is not recommended as
overlay size varies a lot towards the end of the screen. This
causes unstable DMA which results into tearing again.

Rendering small buffers with lower burst size doesn't
cause any noticable performance overhead. 128 pixel width is
selected based on mulitple experiments with exynos5 SoCs.
Signed-off-by: NRahul Sharma <Rahul.Sharma@samsung.com>
Signed-off-by: NPrathyush K <prathyush.k@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch separates dpi related routines from fimd.

Changelog v2:
- Rename ctx->dpi to ctx->display
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch adds component framework support to resolve
the probe order issue.

Until now, exynos drm had used codes specific to exynos drm
to resolve that issue so with this patch, the specific codes
are removed.
Signed-off-by: NInki Dae <inki.dae@samsung.com>

If any fimd channel was already active, initializing iommu will result
in a PAGE FAULT (e.e. u-boot could have turned on the display and
not disabled it before the kernel starts). This patch checks if any
channel is active before initializing iommu and disables it.
Signed-off-by: NAkshu Agrawal <akshu.a@samsung.com>
Signed-off-by: NPrathyush K <prathyush.k@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch removes unused vidcon0 field from fimd_context structure.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch adds parallel output interface to FIMD device driver.
It also restores support for panels initialized by boot loader,
but without proper kernel driver.
Driver uses video interface bindings to find connected panel.
It uses drm_panel interface to interact with the panel.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch corrects porch calculation. It should
be calculated as a difference between adjacent
respective fields of drm_display_mode.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NDaniel Kurtz <djkurtz@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch removes all of the suspend/resume logic from the individual
drivers and consolidates it in drm_drv. This consolidation reduces the
number of functions which enable/disable the hardware to just one -- the
dpms callback. This ensures that we always power up/down in a consistent
manner.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch separates the fimd_activate function into poweron/poweroff
functions to be more consistent with the other drivers in exynos drm. It
also properly cleans up after failures in poweron. The functions have
also been shuffled around such that they are all in the same
spot in the file and poweron/poweroff can be called from the dpms function.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch moves the exynos_drm_display implementation from fimd into
the dp driver. This will allow for tighter integration of the dp driver
into the exynos drm driver.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch removes a few fimd_context members which are either entirely
unused or unneeded.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch uses the mode passed into mode_set to configure fimd instead
of directly using the panel from context. This will allow us to move
the exynos_drm_display implementation out of fimd, where it doesn't
belong.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch splits display and manager from subdrv. The result is that
crtc functions can directly call into manager callbacks and encoder
functions can directly call into display callbacks. This will allow
us to remove the exynos_drm_hdmi shim and support mixer/hdmi & fimd/dp
with common code.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch renames the display_op power_on to dpms to accurately reflect
what the function does.

The side-effect of this patch is that the new hdmi dpms callback is now
invoked twice in the dpms path. This is safe and will be dealt with when
the exynos_drm shim goes away.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch removes the apply() manager callback in favor of putting the
relevant commits in the individual drivers. This will mitigate some of
the difference between the suspend/resume path and the dpms path
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch changes the manager ops callbacks from accepting the subdrv
device pointer to taking a pointer to the manager. This will allow us
to move closer to decoupling manager/display from subdrv, and subsequently
decoupling the crtc/plane from the encoder.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch implements the intitialize manager op in fimd. This will
allow us to keep track of drm_dev in context instead of using subdev,
which in turn makes it easier to remove subdev from fimd.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This patch merges overlay_ops into manager_ops. In all cases,
overlay_ops is implemented in the same place as manager ops, it doesn't
serve a functional purpose, and doesn't make things more clear.
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

DRM_HZ and DRM_WAKEUP macros are removed, but they still remained.
So this patch fixes build errors by replacing the macros.
Signed-off-by: NSeung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Less yelling ftw!
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Fixed a trivial typo.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

irq_enabled is only ever 0 or 1, so make it a bool.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>