There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.

Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove one inline keyword, and no need for a loop to find
an index into a table.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
Support for the Broadcom GENET driver

This patchset adds support for the Broadcom GENET Gigabit Ethernet MAC
controller. This controller is found on the Broadcom BCM7xxx Set Top Box
System-on-a-chips.

Changes since v4:
- add dependency on CONFIG_OF

Changes since v3:
- fixed Kconfig dependency on FIXED_PHY

Changes since v2:
- dropped the patch that adds an "internal" phy-mode
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add myself as a maintainer of the Broadcom GENET driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the Device Tree bindings for the Broadcom GENET Gigabit
Ethernet controller. A bunch of examples are provided to illustrate the
versatile aspect of the hardare.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a new configuration symbol: CONFIG_BCMGENET which allows
us to build the Broadcom GENET driver and hook the driver files into the
build system.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for configuring the port multiplexer hardware
which resides in front of the GENET Ethernet MAC controller. This allows
us to support:

- internal PHYs (using drivers/net/phy/bcm7xxx.c)
- MoCA PHYs which are an entirely separate hardware block not covered
  here
- external PHYs and switches

Note that MoCA and switches are currently supported using the emulated
"fixed PHY" driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the BCMGENET main driver file which supports the
following:

- GENET hardware from V1 to V4
- support for reading the UniMAC MIB counters statistics
- support for the 5 transmit queues
- support for RX/TX checksum offload and SG
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patchs adds the bcmgenet.h header file which contains all the
hardware definitions for the GENETv1 to v4 hardware blocks as well as
the driver private structure and MIB counters.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for the Broadcom BCM7xxx Set Top Box SoCs
internal PHYs. This driver supports the following generation of SoCs:

- BCM7366, BCM7439, BCM7445 (28nm process)
- all 40nm and 65nm (older MIPS-based SoCs)

The PHYs on these SoCs require a bunch of workarounds to operate
correctly, both during configuration time and at suspend/resume time,
the driver handles that for us.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Broadcom BCM54xx register definitions are shared between BCM54xx and
BCM7xx internal PHYs for which we are adding support. Extract these
register definitions and put them in include/linux/brcmphy.h for use by
the BCM7xxx internal PHY driver.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MoCA PHYs are using coaxial (BNC-like) connectors, update the
transceiver port type when replying to ethtool.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some Ethernet MACs are connected to a MoCA PHY which will handle the
low-level job of sending Ethernet frames on the coaxial cable, these
Ethernet MACs need to know about it to be properly configured.
Add a new PHY mode "moca" and update the Device Tree parsing logic to
look for it.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace some magic numbers which describe states of GE model
loss generator with enumerate.
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In netem_change(), we have already get "struct netem_sched_data *q".
Replace params of get_correlation() and other similar functions with
"struct netem_sched_data *q".
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

get_dist_table() and get_loss_clg() may be failed. These
two functions should be called after setting the members
of qdisc_priv(sch), or it will break the old settings while
either of them is failed.
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets which have L2 address different from ours should be
already filtered before entering into ip_forward().

Perform that check at the beginning to avoid processing such packets.
Signed-off-by: NDenis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of my pet coding style peeves is the practice of
adding extra return; at the end of function.
Kill several instances of this in network code.

I suppose some coccinelle wizardy could do this automatically.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 684bad11 "tcp: use PRR to reduce cwin in CWR state" removed all
calls to min_cwnd, so we can safely remove it.
Also, remove tcp_reno_min_cwnd because it was only used for min_cwnd.
Signed-off-by: NStanislav Fomichev <stfomichev@yandex-team.ru>
Acked-by: NYuchung Cheng <ycheng@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently multi-channel configuration is read via the QUERY_FW_CONFIG cmd.
This method has been deprecated by the Skyhawk-R FW. Instead,
GET_PROFILE_CONFIG::port-desc must be used to query this configuration.

This patch also:
a) introduces a few macros to identify certain categories of multi-channel
configs
2) re-factors the be_cmd_set_profile_config() code to be able to read any kind
of desc (and not just the nic-desc.)
Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NVasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: NSathya Perla <sathya.perla@emulex.com>
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch logs a kernel message when a HW error(SLIPORT_ERROR in Lancer and UE
in BEx/Skyhawk) is detected. The log message for BE3 was missing earlier.
This patch also refactors the code by segregating error-detection and reporting
code for Lancer and BEx/SH.
Signed-off-by: NSomnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

linux-can-next-for-3.15-20140212

Marc Kleine-Budde says:

====================
this is a pull request of eight patches for net-next/master.

Florian Vaussard contributed a series that merged the sja1000 of_platform
into the platform driver. The of_platform driver is finally removed.
Stephane Grosjean supplied a patch to allocate CANFD skbs. In a patch
by Uwe Kleine-König another missing copyright information was added to
a userspace header. And a patch by Yoann DI RUZZA that adds listen only
mode to the at91_can driver.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prefer pr_*(...) to printk(KERN_* ...).
Signed-off-by: NYang Yingliang <yangyingliang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver #define's and uses ETHERSMALL macro for the minimum Ethernet frame
size for which we have a standard macro ETH_ZLEN.  Use the latter  instead of
the home-grown one.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jon Maloy says:

====================
tipc: clean up media and bearer layer

This commit series aims at facilitating future changes to the
locking policy around nodes, links and bearers.

Currently, we have a big read/write lock (net_lock) that is used for
serializing all changes to the node, link and bearer lists, as well
as to their mutual pointers and references.

But, in order to allow for concurrent access to the contents of these
structures, net_lock is only used in read mode by the data path code,
and hence a finer granular locking policy must be applied inside the
scope of net_lock: a spinlock (node_lock) for each node structure,
and another one (bearer_lock) for protection of bearer structures.

This locking policy has proved hard to maintain. We have several
times encountered contention problems between node_lock and
bearer_lock, and with the advent of the RCU locking mechanism we
feel it is anyway obsolete and ripe for improvements.

We now plan to replace net_lock with an RCU lock, as well as
getting rid of bearer_lock altogether. This will both reduce data
path overhead and make the code more manageable, while reducing the
risk of future lock contention problems.

Prior to these changes, we need to do some necessary cleanup and
code consolidation. This is what we do with this commit series,
before we finally remove bearer_lock. In a later series we will
replace net_lock with an RCU lock.

v2:
 - Re-inserted a removed kerneldoc entry in commit#5, based on
   feedback from D. Miller.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In an earlier commit, ("tipc: remove links list from bearer struct")
we described three issues that need to be pre-emptively resolved before
we can remove tipc_net_lock. Here we resolve issue a) described in that
commit:

"a) In access method #2, we access the link before taking the
    protecting node_lock. This will not work once net_lock is gone,
    so we will have to change the access order. We will deal with
    this in a later commit in this series."

Here, we change that access order, by ensuring that the function
link_find_link() returns only a safe reference for finding
the link, i.e., a node pointer and an index into its 'links' array,
not the link pointer itself. We also change all callers of this
function to first take the node lock before they can check if there
still is a valid link pointer at the returned index. Since the
function now returns a node pointer rather than a link pointer,
we rename it to the more appropriate 'tipc_link_find_owner().
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the earlier commits ("tipc: remove 'links' list from
tipc_bearer struct") and ("tipc: introduce new spinlock to protect
struct link_req"), there is no longer any need to protect struct
link_req or or any link list by use of bearer_lock. Furthermore,
we have eliminated the need for using bearer_lock during downcalls
(send) from the link to the bearer, since we have ensured that
bearers always have a longer life cycle that their associated links,
and always contain valid data.

So, the only need now for a lock protecting bearers is for guaranteeing
consistency of the bearer list itself. For this, it is sufficient, at
least for the time being, to continue applying 'net_lock´ in write mode.

By removing bearer_lock we also pre-empt introduction of issue b) descibed
in the previous commit "tipc: remove 'links' list from tipc_bearer struct":

"b) When the outer protection from net_lock is gone, taking
    bearer_lock and node_lock in opposite order of method 1) and 2)
    will become an obvious deadlock hazard".

Therefore, we now eliminate the bearer_lock spinlock.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a bearer is disabled, all its attached links are deleted.
Ideally, we should do link failover to redundant links on other bearers,
if there are any, in such cases. This would be consistent with current
behavior when a link is reset, but not deleted. However, due to the
complexity involved, and the (wrongly) perceived low demand for this
feature, it was never implemented until now.

We mark the doomed link for deletion with a new flag, but wait until the
failover process is finished before we actually delete it. With the
improved link tunnelling/failover code introduced earlier in this commit
series, it is now easy to identify a spot in the code where the failover
is finished and it is safe to delete the marked link. Moreover, the test
for the flag and the deletion can be done synchronously, and outside the
most time critical data path.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We change the order of checking for destination users when processing
incoming packets. By placing the checks for users that may potentially
replace the processed buffer, i.e., CHANGEOVER_PROTOCOL and
MSG_FRAGMENTER, in a separate step before we check for the true end
users, we get rid of a label and a 'goto', at the same time making the
code more comprehensible and easy to follow.

This commit does not change any functionality, it is just a cosmetic
code reshuffle.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the previous redesign of the tunnel reception algorithm and
functions, we finalize it by renaming a couple of stack variables
in tipc_tunnel_rcv(). This makes it more consistent with the naming
scheme elsewhere in this part of the code.

This change is purely cosmetic, with no functional changes.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We simplify and slim down the code in function tipc_tunnel_rcv()
No impact on the users of this function.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the earlier commits in this series related to the function
tipc_link_tunnel_rcv(), we can now go further and simplify its
signature.

The function now consumes all DUPLICATE packets, and only returns such
ORIGINAL packets that are ready for immediate delivery, i.e., no
more link level protocol processing needs to be done by the caller.
As a consequence, the the caller, tipc_rcv(), does not access the link
pointer after call return, and it becomes unnecessary to pass a link
pointer reference in the call. Instead, we now only pass it the tunnel
link's owner node, which is sufficient to find the destination link for
the tunnelled packet.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a link is reset, and there is a redundant link available, all
sender sockets will steer their subsequent traffic through the
remaining link. In order to guarantee preserved packet order and
cardinality during the transition, we tunnel the failing link's send
queue through the remaining link before we allow any sockets to use it.

In this commit, we change the algorithm for receiving failover
("ORIGINAL_MSG") packets in tipc_link_tunnel_rcv(), at the same time
delegating it to a new subfuncton, tipc_link_failover_rcv(). Instead
of directly returning an extracted inner packet to the packet reception
loop in tipc_rcv(), we first check if it is a message fragment, in which
case we append it to the reset link's fragment chain. If the fragment
chain is complete, we return the whole chain instead of the individual
buffer, eliminating any need for the tipc_rcv() loop to do reassembly of
tunneled packets.

This change makes it possible to further simplify tipc_link_tunnel_rcv(),
as well as the calling tipc_rcv() loop. We will do that in later
commits. It also makes it possible to identify a single spot in the code
where we can tell that a failover procedure is finished, something that
is useful when we are deleting links after a failover. This will also
be done in a later commit.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a second link to a destination comes up, some sender sockets will
steer their subsequent traffic through the new link. In order to
guarantee preserved packet order and cardinality for those sockets, we
tunnel a duplicate of the old link's send queue through the new link
before we open it for regular traffic. The last arriving packet copy,
on whichever link, will be dropped at the receiving end based on the
original sequence number, to ensure that only one copy is delivered to
the end receiver.

In this commit, we change the algorithm for receiving DUPLICATE_MSG
packets, at the same time delegating it to a new subfunction,
tipc_link_dup_rcv(). Instead of returning an extracted inner packet to
the packet reception loop in tipc_rcv(), we just add it to the receiving
(new) link's deferred packet queue. The packet will then be processed by
that link when it receives its first non-tunneled packet, i.e., at
latest when the changeover procedure is finished.

Because tipc_link_tunnel_rcv()/tipc_link_dup_rcv() now is consuming all
packets of type DUPLICATE_MSG, the calling tipc_rcv() function can omit
testing for this. This in turn means that the current conditional jump
to the label 'protocol_check' becomes redundant, and we can remove that
label.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In our ongoing effort to simplify the TIPC locking structure,
we see a need to remove the linked list for tipc_links
in the bearer. This can be explained as follows.

Currently, we have three different ways to access a link,
via three different lists/tables:

1: Via a node hash table:
   Used by the time-critical outgoing/incoming data paths.
   (e.g. link_send_sections_fast() and tipc_recv_msg() ):

grab net_lock(read)
   find node from node hash table
   grab node_lock
       select link
       grab bearer_lock
          send_msg()
       release bearer_lock
   release node lock
release net_lock

2: Via a global linked list for nodes:
   Used by configuration commands (link_cmd_set_value())

grab net_lock(read)
   find node and link from global node list (using link name)
   grab node_lock
       update link
   release node lock
release net_lock

(Same locking order as above. No problem.)

3: Via the bearer's linked link list:
   Used by notifications from interface (e.g. tipc_disable_bearer() )

grab net_lock(write)
   grab bearer_lock
      get link ptr from bearer's link list
      get node from link
      grab node_lock
         delete link
      release node lock
   release bearer_lock
release net_lock

(Different order from above, but works because we grab the
outer net_lock in write mode first, excluding all other access.)

The first major goal in our simplification effort is to get rid
of the "big" net_lock, replacing it with rcu-locks when accessing
the node list and node hash array. This will come in a later patch
series.

But to get there we first need to rewrite access methods ##2 and 3,
since removal of net_lock would introduce three major problems:

a) In access method #2, we access the link before taking the
   protecting node_lock. This will not work once net_lock is gone,
   so we will have to change the access order. We will deal with
   this in a later commit in this series, "tipc: add node lock
   protection to link found by link_find_link()".

b) When the outer protection from net_lock is gone, taking
   bearer_lock and node_lock in opposite order of method 1) and 2)
   will become an obvious deadlock hazard. This is fixed in the
   commit ("tipc: remove bearer_lock from tipc_bearer struct")
   later in this series.

c) Similar to what is described in problem a), access method #3
   starts with using a link pointer that is unprotected by node_lock,
   in order to via that pointer find the correct node struct and
   lock it. Before we remove net_lock, this access order must be
   altered. This is what we do with this commit.

We can avoid introducing problem problem c) by even here using the
global node list to find the node, before accessing its links. When
we loop though the node list we use the own bearer identity as search
criteria, thus easily finding the links that are associated to the
resetting/disabling bearer. It should be noted that although this
method is somewhat slower than the current list traversal, it is in
no way time critical. This is only about resetting or deleting links,
something that must be considered relatively infrequent events.

As a bonus, we can get rid of the mutual pointers between links and
bearers. After this commit, pointer dependency go in one direction
only: from the link to the bearer.

This commit pre-empts introduction of problem c) as described above.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the 'started' field in struct tipc_link represents only a
binary state, 'started' or 'not started'. We need it to represent
more link execution states in the coming commits in this series.
Hence, we rename the field to 'flags', and define the current
started/non-started state to be represented by the LSB bit of
that field.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We break out the code for deleting attached links in the
function bearer_disable(), and define a new function named
tipc_link_delete_list() to do this job.

This commit incurs no functional changes, but makes the code of
function bearer_disable() cleaner. It is also a preparation
for a more important change to the bearer code, in a subsequent
commit in this series.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We break out the code for resetting attached links in the
function tipc_reset_bearer(), and define a new function named
tipc_link_reset_list() to do this job.

This commit incurs no functional changes, but makes the code
of function tipc_reset_bearer() cleaner. It is also a preparation
for a more important change to the bearer code, in a subsequent
commit in this series.
Signed-off-by: NYing Xue <ying.xue@windriver.com>
Reviewed-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function tipc_link_recv_fragment(struct sk_buff **buf) currently
leaves the value of the input buffer pointer undefined when it returns,
except when the return code indicates that the reassembly is complete.
This despite the fact that it always consumes the input buffer.

Here, we enforce a stricter behavior by this function, ensuring that
the returned buffer pointer is non-NULL if and only if the reassembly
is complete. This makes it possible to test for the buffer pointer as
criteria for successful reassembly.

We also rename the function to tipc_link_frag_rcv(), which is both
shorter and more in line with common naming practice in the network
subsystem.

Apart from the new name, these changes have no impact on current
users of the function, but makes it more practical for use in some
planned future commits.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Reviewed-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>