This looks like left over text in the kernel parameters documentation.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

asus_acpi_init() has a hack to prevent the driver from loading
when asus_hotk_add() fails.  However, it was returning the successful
return value of acpi_bug_registger_driver() on failure.  This caused
an oops on unload.  Instead it should return -ENODEV.
Signed-off-by: NThomas Renninger <trenn@suse.de>
Signed-off-by: NLen Brown <len.brown@intel.com>

I have a Dell Optiplex GX240 and when I boot Linux, ACPI gets set up by only
acpi=ht.  dmesg shows the following line:

   DELL GX240 detected: force use of acpi=ht

Everything seemed to be fine.  However, I discovered that everything is not
fine.  The USB controller works so slowly that copying a few (uncached) 1
megabyte large photos from a USB-enabled digital camera takes many minutes
instead of a couple of seconds.

I am using Linux 2.6.21.1 on a Debian 4.0 ("Etch") system.

I thought that this might be related to ACPI.  So I tried to boot with _only_
"acpi=force" appended to the kernel command line.  Voila, the USB controller
started to work at full speed and copying photos from my digital camera took
only seconds.

I tested the system with "acpi=force" and could not find anything which did
not work.

I thought that this might be related to interrupts and APIC as well.  (Note
that this is APIC, not ACPI.) I tried booting with _only_ "noapic" and
"nolapic" appended to the command line.  Again, the USB controller started to
work at full speed.
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLen Brown <len.brown@intel.com>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: Install firewire-constants.h and firewire-cdev.h for userspace.
  firewire: Change struct fw_cdev_iso_packet to not use bitfields.
  firewire: Implement suspend/resume PCI driver hooks.
  firewire: add to MAINTAINERS
  firewire: fw-sbp2: implement sysfs ieee1394_id
  ieee1394: sbp2: offer SAM-conforming target port ID in sysfs
  ieee1394: fix calculation of sysfs attribute "address"

Make timer-stats have almost zero overhead when enabled in the config but
not used.  (this way distros can enable it more easily)

Also update the documentation about overhead of timer_stats - it was
written for the first version which had a global lock and a linear list
walk based lookup ;-)
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix two races in the timer stats lookup code.  One by ensuring that the
initialization of a new entry is finished upon insertion of that entry.
The other by cleaning up the hash table when the entries array is cleared,
so that we don't have any "pre-inserted" entries.

Thanks to Eric Dumazet for reminding me of the memory barriers.
Signed-off-by: NBjorn Steinbrink <B.Steinbrink@gmx.de>
Signed-off-by: NIan Kumlien <pomac@vapor.com>
Acked-by: NIngo Molnar <mingo@elte.hu>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix following section mismatch warning in hp100:

WARNING: drivers/net/hp100.o(.init.text+0x26a): Section mismatch: reference to .exit.text: (after 'init_module')

The warning says that we use a function marked __exit from a
function marked __init.
This is not good on architectures where we discard __exit section
for drivers that are built-in.

Note: This warning is only seen by my local copy of modpost
      but the change will soon hit upstream.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix following section mismatch warning in kvm-intel.o:
WARNING: o-i386/drivers/kvm/kvm-intel.o(.init.text+0xbd): Section mismatch: reference to .exit.text: (between 'hardware_setup' and 'vmx_disabled_by_bios')

The function free_kvm_area is used in the function alloc_kvm_area which
is marked __init.
The __exit area is discarded by some archs during link-time if a
module is built-in resulting in an oops.

Note: This warning is only seen by my local copy of modpost
      but the change will soon hit upstream.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix following section mismatch warnings in acpi

WARNING: drivers/acpi/asus_acpi.o(.init.text+0xb7): Section mismatch: reference to .exit.text: (after 'init_module')
WARNING: o-i386/drivers/acpi/toshiba_acpi.o(.init.text+0x13a): Section mismatch: reference to .exit.text: (after 'init_module')

The exit function is used in the init function during an error codition.
As __exit may be discarded during link-time / run-time this is no good.
Do not mark the exit function __exit.

Note: This warning is only seen by my local copy of modpost
      but the change will soon hit upstream.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following section mismatch warnings:

WARNING: drivers/isdn/hardware/eicon/divadidd.o(.init.text+0xc4): Section mismatch: reference to .exit.text: (between 'init_module' and 'diddfunc_init')
WARNING: drivers/isdn/hardware/eicon/divas.o(.init.text+0xf4): Section mismatch: reference to .exit.text:divasfunc_exit (between 'init_module' and 'divasfunc_init')
WARNING: drivers/isdn/hardware/eicon/divas.o(.init.text+0x10d): Section mismatch: reference to .exit.text:divasfunc_exit (between 'init_module' and 'divasfunc_init')
WARNING: drivers/isdn/hardware/eicon/divas.o(.init.text+0x148): Section mismatch: reference to .exit.text:divasfunc_exit (between 'init_module' and 'divasfunc_init')

They all point to situation whare a function marked __init calls a function
marked __exit - but the __exit section may have been discarded.

Note: This warning is generated by a modified copy of modpost in my
      tree. It will soon hit upstearm.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following section mismatch warnings in microcode.c:
WARNING: arch/i386/kernel/built-in.o(.init.text+0x3966): Section mismatch: reference to .exit.text: (between 'microcode_init' and 'parse_maxcpus')
WARNING: arch/i386/kernel/built-in.o(.init.text+0x3992): Section mismatch: reference to .exit.text: (between 'microcode_init' and 'parse_maxcpus')

The warning are caused by a function marked __init that
calls a function marked __exit.
Functions marked __exit may be discarded either during link or run-time
and thus the reference is not good.
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch correctly restores console state after switching from X.
Otherwise, screen is always off after switching from X.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Hotplug callbacks are performed with interrupts enabled.  Slub requires
interrupts to be disabled for flushing caches.
Signed-off-by: NChristoph Lameter <clameter@sgi.com>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix 2 bugs:

- SPI_DMA_RHDMA bad value.

- Missing return value in setup() function (lost passing from
  patch-2.6.20-rc4-spi_imx to patch-2.6.20-rc6-spi_imx).
Signed-off-by: NAndrea Paterniani <a.paterniani@swapp-eng.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The <linux/serial_core.h> header refers to handle_sysrq(), but does not
include <linux/sysrq.h> which provides a declaration of the function.  This
may result in an implicit declaration and a warning if the actual one is
seen later on.
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add comment for errnos related to restart syscall to avoid the leakage of
them to user programs.
Signed-off-by: NSatoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: NRoland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

1. arch/alpha/Kconfig

   several adjustments:
      a) additions to the systems list and cleanup of same
      b) change limits of NR_CPUS and make dep. on platform

   Note that MARVEL support is limited to 32 CPUs whan using
   42-bit KSEG - one needs 48-bit KSEG to handle up to 64, and
   we've never supported 48-bit KSEG.

2. include/asm-alpha/core_wildfire.h

   fix a typo that undoubtedly prevents WILDFIRE support
   from working
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This code corrects the behavior of the t2_readX/t2_writeX routines,
and t2_ioreadNN/t2_iowriteNN routines.

The value T2_DENSE_MEM is now subtracted from the "xaddr" argument in
each of the readX/writeX routines, since those routines may be called
directly, rather than always through the ioreadNN/iowriteNN routines.

Examples of the direct calls, via the __raw_readX/writeX macros, are
the memcpy_fromio/toio, _memset_c_io, and scr_memcpyw routines.
Signed-off-by: NJay Estabrook <jay.estabrook@hp.com>
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This code replaces earlier and incomplete handling of graphics on non-zero PCI
domains (aka hoses or peer PCI buses).

An option (CONFIG_VGA_HOSE) is set TRUE if configuring a GENERIC kernel, or a
kernel for MARVEL, TITAN, or TSUNAMI machines, as these are the machines whose
SRM consoles are capable of configuring and handling graphics options on
non-zero hoses.  All other machines have the option set FALSE.

A routine, "find_console_vga_hose()", is used to find the graphics device
which the machine's firmware believes is the console device, and it sets a
global (pci_vga_hose) for later use in managing access to the device.  This is
called in "init_arch" on TITAN and TSUNAMI machines; MARVEL machines use a
custom version of this routine because of extra complexity.

A routine, "locate_and_init_vga()", is used to find the graphics device and
set a global (pci_vga_hose) for later use in managing access to the device, in
the case where "find_console_vga_hose" has failed.

Various adjustments are made to the ioremap and ioportmap routines for
detecting and translating "legacy" VGA register and memory references to the
real PCI domain.

[akpm@linux-foundation.org: don't statically init bss]
[akpm@linux-foundation.org: build fix]
Signed-off-by: NJay Estabrook <jay.estabrook@hp.com>
Signed-off-by: NIvan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- warning fix.
- call trace area check fix.
- There is no meaning, ' & ' it deletes
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When either rx_buf or tx_buf is not being used, i.e.  for plain read- or
write operations, the atmel_spi uses a fixed-size DMA buffer instead.  If
the transfer is longer than the size of this buffer, it is split into
multiple DMA transfers.

When the transfer is split like this, the atmel_spi driver ends up using
the same DMA address again and again even for the buffer that came from the
user, which is of course wrong.  Fix this by adding the number of bytes
already transferred to the DMA address so that the data ends up in the
right place.

Thanks to Wu Xuan for discovering this bug.
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Cc: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I noticed that CLIR (aka "hide your calling number") in isdn_tty is broken:
The at-command parser filters out the required "R" (e.g.  ATDR089123456)
It's been broken for a *very* long time.
Signed-off-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NMatthias Goebl <matthias.goebl@goebl.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

According to the definitions recently posted on LKML, the maturity label
for the ISDN4Linux subsystem is wrong.  This patch corrects it and also
clarifies the accompanying help text a bit.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Acked-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Spotted by Satoru Takeuchi.

kill_pgrp(task_pgrp(current)) sends the signal to the current's thread
group, but can choose any sub-thread as a target for signal_wake_up().
This means that job_control() and tty_check_change() may return
-ERESTARTSYS without signal_pending().
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Satoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Cc: Roland McGrath <roland@redhat.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

zone->present_pages is updated in online_pages().  But, __add_zone() can be
called twice or more before calling online_pages().  So,
init_currenty_empty_zone() can be called unnecessary times.  It is cause of
memory leak of zone's wait_table.
Signed-off-by: NYasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Intel Macs (and possibly other machines) provide a PNP entry for the RTC,
but provide no IRQ.  As a result the rtc-cmos driver doesn't allow wakeup
alarms.  If the RTC is located at the legacy ioport range, assume that it's
on IRQ 8 unless the tables say otherwise.
Signed-off-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Adds instructions how to use GDB to figure out the exact location of
an OOPS to Documentation/BUG-HUNTING.
Signed-off-by: NPekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We are seeing increasing levels of minor patch style violations in submissions
to the mailing lists as well as making it into the tree.  These detract from
the quality of the submission and cause unnessary work for reviewers.

As a first step package up the current state of the patch style checker and
include it in the kernel tree.  Add instructions suggesting running it on
submissions.  This adds version v0.01 of the checkpatch.pl script.
Signed-off-by: NAndy Whitcroft <apw@shadowen.org>
Signed-off-by: NJoel Schopp <jschopp@austin.ibm.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>
Cc: Alex Dubov <oakad@yahoo.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move the forward declaration of fb_class from drivers/video/console/fbcon.h to
<linux/fb.h>, together with the other forward declarations related to
drivers/video/fbmem.c.

This kills the following sparse warning:
| drivers/video/fbmem.c:1363:14: warning: symbol 'fb_class' was not declared. Should it be static?
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Because the framebuffer memory is allocated system RAM, use the sys_ drawing
libraries. It also fixes the following compile error:

  LD      .tmp_vmlinux1
drivers/built-in.o:(.data+0x8b48): undefined reference to `cfb_fillrect'
drivers/built-in.o:(.data+0x8b50): undefined reference to `cfb_copyarea'
drivers/built-in.o:(.data+0x8b58): undefined reference to `cfb_imageblit'

[adaplas]
Use fb_sys_read/write for the same reasons as above.
Signed-off-by: NAvuton Olrich <avuton@gmail.com>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch prevents null pointer dereference in arkfb and vt8623fb.
Signed-off-by: NOndrej Zajicek <santiago@crfreenet.org>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch fixes wrong ifdef around the xxxfb_setup. It also moves this
function to remove forward declaration.
Signed-off-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NAntonino Daplas <adaplas@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When the private futex support was added the compat code wasn't changed.
The result is that code using compat code which fail, e.g., because the
timeout values are not correctly passed.  The following patch should fix
that.
Signed-off-by: NUlrich Drepper <drepper@redhat.com>
Cc: Eric Dumazet <dada1@cosmosbay.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Force Dell E520 to use the BIOS to shutdown/reboot.

I have at least one report that this patch fixes shutdown/reboot
problems on the Dell E520 platform.

(Andi says: People can always set the boot option.  It hardly seems like a
critical issue needing a backport.)
Signed-off-by: NTim Gardner <tim.gardner@ubuntu.com>
Acked-by: NAndi Kleen <ak@suse.de>
Acked-by: NMatt Domsch <Matt_Domsch@dell.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Chuck reports that the recent fix from Andi to oprofile
6c977aad introduces a double free.  Each
cpu's cpu_msrs is setup to point to cpu 0's, which causes free_msrs to free
cpu 0's pointers for_each_possible_cpu.  Rather than copy the pointers, do
a deep copy instead.

[acme@redhat.com: allocate_msrs() was using for_each_online_cpu()]
Signed-off-by: NChris Wright <chrisw@sous-sol.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Dave Jones <davej@redhat.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch updates the Intel ICH9M LPC Controller DID's, due to a
specification change.
Signed-off-by: NJason Gaston <jason.d.gaston@intel.com>
Cc: <stable@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix various bits of obviously-busted code which we're not happening to
compile, due to ifdefs.

Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Jan Kara <jack@ucw.cz>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I have made a tool to parse the kernel that does not pre-process the
source.  That means that my parser tries to parse all the code, including
code in the #else branch or code that is not often compiled because the
driver is not very used (or not used at all).  So, my parser sometimes
reports parse error not originally detected by gcc.  Here is my (first)
patch.

[akpm@linux-foundation.org: fix amd8111e.c]
Signed-off-by: NYoann Padioleau <padator@wanadoo.fr>
Acked-by: NMatthew Wilcox <matthew@wil.cx>
Acked-by: NWim Van Sebroeck <wim@iguana.be>
Acked-by: NDavid Woodhouse <dwmw2@infradead.org>
Acked-by: NJeff Garzik <jeff@garzik.org>
Acked-by: NJames Bottomley <James.Bottomley@steeleye.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>