D0i3 adds additional interrupt reason bit, therefore we add a variable
intr_source to save the interrupt causes for further dispatching.
The interrupt cause is saved in the irq quick handler to achieve
unified behavior for both MSI enabled and shared interrupt platforms.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Detect d0i3 low power state during hw configuration,
the value is set in HFS_1 pci config reigister.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The current power gating naming was confusing,
we wish to swap meanings of register and flow level power gating terms,

For registers writing level use terms set and unset:
	mei_me_pg_set, mei_me_pg_unset

For flow/high level use power gating enter and power gating exit terms
	mei_me_pg_enter_sync, mei_me_pg_exit_sync
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

ME devices prior to PCH8 (Lynx Point) have two FW status registers,
on PCH8 and newer excluding txe there are six FW status registers.
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Kill host_hw_status and me_hw_state from me hw structure that used
to cache host and me csr values.
We do not use the cached values across the function calls anymore
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add missed parameters descriptions and return values descriptions
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Device specific configurations are currently only needed by me hw
so we can remove it from txe
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Move quirk FW type detector to cfg structure
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add mei_cfg structure that holds per device configuration
data and hooks, as the first step we add firmware
status register offsets
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add runtime pm framework for ME devices.
The runtime pm handlers are used to run
me power gating isolation protocol
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For power gating entry we write hbm pg entry request command and
then we set pg register
For power gating exit we clear pg register and wait for exit request
hbm command.

Exit power gating request might also be initiated by the firmware
w/o explicit driver request

The power gating state is tracked by pg_state member of me_hw
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NAlexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We currently include <linux/irqreturn.h> in <linux/pci.h>, but I'm about to
remove that from linux/pci.h, so add explicit includes where needed.
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>

1. Move the mei_data2slots to mei_dev.h as it will be used
by the all supported HW.
2. Change return value from u8 to u32 to catch possible overflows
3. Eliminate computing the slots number twice in the same function
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

interrupt handler are  platform specifics so we move
them to hw-mei.c. For sake of that we need to export
write, read, and complete handlers from the interrupt.c
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We add struct mei_hw_ops to virtualize access to hw specific
configurations. This allows us to separate the compilation
of the ME interface from the ME hardware specifics
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is initial step of move the ME hw specifics
out of mei_device structure into mei_me_hw
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Rename hw-me.h to hw-me-regs.h as this file
contains only register definitions.
Files hw-me.[ch] now contains ME hw dependant
functionality
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>