- 05 8月, 2010 1 次提交
-
-
由 Manuel Lauss 提交于
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY. Signed-off-by: NManuel Lauss <manuel.lauss@googlemail.com> To: Linux-MIPS <linux-mips@linux-mips.org> Patchwork: https://patchwork.linux-mips.org/patch/1461/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 14 5月, 2009 1 次提交
-
-
由 Zhang Le 提交于
Quoting from Loongson2FUserGuide.pdf: 5.22.1 Hazards The processor detects most of the pipeline hazards in hardware, including CP0 hazards and load hazards. No NOP instructions are required to correct instruction sequences. Signed-off-by: NZhang Le <r0bertz@gentoo.org> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 30 3月, 2009 1 次提交
-
-
由 Manuel Lauss 提交于
The Alchemy manuals state: "All pipeline hazards and dependencies are enforced by hardware interlocks so that any sequence of instructions is guaranteed to execute correctly. Therefore, it is not necessary to pad legacy MIPS hazards (such as load delay slots and coprocessor accesses) with NOPs." Run-tested on Au12x0, without any ill effects. Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 12 3月, 2009 1 次提交
-
-
由 Shinya Kuribayashi 提交于
Current VR5500 processor support lacks of some functions which are expected to be configured/synthesized on arch initialization. Here're some VR5500A spec notes: * All execution hazards are handled in hardware. * Once VR5500A stops the operation of the pipeline by WAIT instruction, it could return from the standby mode only when either a reset, NMI request, or all enabled interrupts is/are detected. In other words, if interrupts are disabled by Status.IE=0, it keeps in standby mode even when interrupts are internally asserted. Notes on WAIT: The operation of the processor is undefined if WAIT insn is in the branch delay slot. The operation is also undefined if WAIT insn is executed when Status.EXL and Status.ERL are set to 1. * VR5500A core only implements the Load prefetch. With these changes, it boots fine. Signed-off-by: NShinya Kuribayashi <shinya.kuribayashi@necel.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 11 1月, 2009 1 次提交
-
-
由 David Daney 提交于
For Cavium CPU, we treat the same as R10000, in that all hazards are dealt with in hardware. Signed-off-by: NTomaso Paoletti <tpaoletti@caviumnetworks.com> Signed-off-by: NPaul Gortmaker <Paul.Gortmaker@windriver.com> Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 11 10月, 2008 1 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 12 10月, 2007 2 次提交
-
-
由 Ralf Baechle 提交于
Tested with Malta; inflates malta_defconfig by 3932 bytes. Ideally there should be additional configuration to allow getting rid of this overhead but that would be too much complexity at this stage of the release cycle. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 12 9月, 2007 1 次提交
-
-
由 Ralf Baechle 提交于
Following a strict interpretation the empty definition of irq_enable_hazard has always been a bug - but an intentional one because it didn't bite. This has now changed, for uniprocessor kernels mm/slab.c:do_drain() [...] on_each_cpu(do_drain, cachep, 1, 1); check_irq_on(); [...] may be compiled into a mtc0 c0_status; mfc0 c0_status sequence resulting in a back-to-back hazard. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 11 9月, 2007 1 次提交
-
-
由 Ralf Baechle 提交于
Following a strict interpretation the empty definition of irq_enable_hazard has always been a bug - but an intentional one because it didn't bite. This has now changed, for uniprocessor kernels mm/slab.c:do_drain() [...] on_each_cpu(do_drain, cachep, 1, 1); check_irq_on(); [...] may be compiled into a mtc0 c0_status; mfc0 c0_status sequence resulting in a back-to-back hazard. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 01 8月, 2007 1 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 11 5月, 2007 2 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Chris Dearman 提交于
Move FPU hazard handling to hazards.h and provide proper support for MIPSR2 processors Signed-off-by: NChris Dearman <chris@mips.com> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 25 3月, 2007 1 次提交
-
-
由 Ralf Baechle 提交于
In the the sequence: ei .. mfc0 $x, $status the mfc0 may not see the SR_IE bit set. This was a deliberate bug in the kernel code because we knew this was a safe thing to do on all R2 silicon so far but new silicon is changing this. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 25 1月, 2007 1 次提交
-
-
由 Yoichi Yuasa 提交于
NEC VR4111 and VR4121 need one more nop with mtc0_tlbw_hazard(). Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp> Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 27 9月, 2006 2 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Mostly based on patch by Chris Dearman and cleanups from Yoichi. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 30 6月, 2006 1 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 26 4月, 2006 1 次提交
-
-
由 David Woodhouse 提交于
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
-
- 19 4月, 2006 1 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 19 3月, 2006 1 次提交
-
-
由 Ralf Baechle 提交于
The SB1 core has a three cycle interrupt disable hazard but we were wrongly treating it as fully interlocked. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 07 2月, 2006 1 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 10 1月, 2006 1 次提交
-
-
由 Ralf Baechle 提交于
Gcc has a tradition of misscompiling the previous construct using the address of a label as argument to inline assembler. Gas otoh has the annoying difference between la and dla which are only usable for 32-bit rsp. 64-bit code, so can't be used without conditional compilation. The alterantive is switching the assembler to 64-bit code which happens to work right even for 32-bit code ... Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 30 10月, 2005 6 次提交
-
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
由 Ralf Baechle 提交于
back mtc0 / mfc0 pairs from the same coprocessor register. Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
-
- 17 4月, 2005 1 次提交
-
-
由 Linus Torvalds 提交于
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
-