platform_get_irq() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: NKevin Hilman <khilman@baylibre.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add the devicetree binding for MT7623 SoC using MT2701 as the fallback.

Cc: devicetree@vger.kernel.org
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

To get an usdhc Apacer and some ATP SD cards work reliable, CMD23 needs
to be disabled.  This has been tested on i.MX6 (sdhci-esdhc) and rk3288
(dw_mmc-rockchip).

Without this patch on i.MX6 (sdhci-esdhc):

 $ dd if=/dev/urandom of=/mnt/test bs=1M count=10 conv=fsync

    | <mmc0: starting CMD23 arg 00000400 flags 00000015>
    | mmc0: starting CMD25 arg 00a71f00 flags 000000b5
    | mmc0:     blksz 512 blocks 1024 flags 00000100 tsac 3000 ms nsac 0
    | mmc0:     CMD12 arg 00000000 flags 0000049d
    | sdhci [sdhci_irq()]: *** mmc0 got interrupt: 0x00000001
    | mmc0: Timeout waiting for hardware interrupt.

Without this patch on rk3288 (dw_mmc-rockchip):

    | mmc1: Card stuck in programming state! mmcblk1 card_busy_detect
    | dwmmc_rockchip ff0c0000.dwmmc: Busy; trying anyway
    | mmc_host mmc1: Bus speed (slot 0) = 400000Hz (slot req 400000Hz,
    | actual 400000HZ div = 0)
    | mmc1: card never left busy state
    | mmc1: tried to reset card, got error -110
    | blk_update_request: I/O error, dev mmcblk1, sector 139778
    | Buffer I/O error on dev mmcblk1p1, logical block 131586, lost async
    | page write
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Cc: <stable@vger.kernel.org> # v4.14+
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Intel DSM function 8 has been used to identify transfer modes that are not
working on some CHT boards. Add support for that.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Tested-by: NCarlo Caione <carlo@endlessm.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a ->setup_host() callback so that device-specific changes can be made
to the mmc host controller before it is added.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_blk_alloc_req() is supposed to return error pointers but there is
one path where we forget to set the error code and accidentally return
NULL.  The callers are not expecting that and will have a NULL pointer
dereference.

Fixes: 41e3efd0 ("mmc: block: Simplify cleaning up the queue")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Absence of parentheses is not affecting current code, but ensure macro
parameters are wrapped in parentheses.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Fixes: a4080225 ("mmc: cqhci: support for command queue enabled host")
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove code no longer needed after the switch to blk-mq.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove code no longer needed after the switch to blk-mq.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove config option MMC_MQ_DEFAULT and parameter mmc_use_blk_mq, so that
blk-mq must be used always.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When system wakes up from sleep on ls1046ardb, the SD operation fails
with mmc error messages since ESDHC_TB_EN bit couldn't be cleaned by
eSDHC_SYSCTL[RSTA]. It's proper to clean this bit in esdhc_reset()
rather than in probe.
Signed-off-by: Nyinbo.zhu <yinbo.zhu@nxp.com>
Acked-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_test disables the command queue because none of the tests use the
command queue. However the Reset Test will re-enable it, so disable it in
that case too.

Fixes: 9d4579a8 ("mmc: mmc_test: Disable Command Queue while mmc_test is used")
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

mmc_test now uses mmc_start_request() to test sending commands during
"ongoing" asynchronous transfers, i.e. tests:
	Commands during non-blocking read - use Set Block Count (CMD23)
	Commands during non-blocking write - use Set Block Count (CMD23)

mmc_start_request() was not initializing cmd_completion, but cmd_completion
is used by "ongoing" transfers, so move initialization of cmd_completion
into making mmc_start_request().

Fixes: cb39f61e ("mmc: core: Export a few functions needed for blkmq support")
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This patch supports HS400 for AMD upcoming emmc 5.0 controller.The
HS400 and HS200 mode requires hardware work around also. This patch
adds the quirks for the same.
Signed-off-by: NNehal-bakulchandra Shah <Nehal-bakulchandra.Shah@amd.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Calling getnstimeofday() can suffer from time jumps and from the
y2038 overflow, so it is not appropriate here. Using ktime_get_ts64()
solves both problems. Using ktime_get() with ktime_t timestamps would
also work, but it seems that we mainly want to print the times as
seconds+nanoseconds, so it would require an extra division in the output.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The power register needs to have a valid voltage set
even when the power supply is managed by  an external regulator.
Signed-off-by: NMilan Stevanovic <milan.o.stevanovic@gmail.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Whitelists for internal DMAC implementation.
Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NWolfram Sang <wsa+renesas@sang-engineering.com>

The function mmc_cqe_issue_type is local to the source and does
not need to be in global scope, so make it static.

Cleans up sparse warning:
drivers/mmc/core/queue.c:62:21: warning: symbol 'mmc_cqe_issue_type'
was not declared. Should it be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

drivers/mmc/core/block.c:2106:9-10: WARNING: return of 0/1 in function 'mmc_blk_status_error' with return type bool

 Return statements in functions returning bool should use
 true/false instead of 1/0.
Generated by: scripts/coccinelle/misc/boolreturn.cocci

Fixes:7eb43d53 ("mmc: block: blk-mq: Stop using legacy recovery")
CC: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The block driver's blk-mq paths do not use mmc_start_areq(). In order to
remove mmc_start_areq() entirely, start by removing it from mmc_test.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

There are only a few things the recovery needs to do. Primarily, it just
needs to:
	Determine the number of bytes transferred
	Get the card back to transfer state
	Determine whether to retry

There are also a couple of additional features:
	Reset the card before the last retry
	Read one sector at a time

The legacy code spent much effort analyzing command errors, but commands
fail fast, so it is simpler just to give all command errors the same number
of retries.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Set a 10 second timeout for polling write request busy state. Note, mmc
core is setting a 3 second timeout for SD cards, and SDHCI has long had a
10 second software timer to timeout the whole request, so 10 seconds should
be ample.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

According to the specification, total access time is derived from both TAAC
and NSAC, which means the timeout should add both timeout_ns and
timeout_clks. Host drivers do that, so make the block driver do that too.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

The card is required to return to transfer state. Since that is the state
required to start another transfer, check for that state instead of
programming state.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Pedantically, ensure the status is checked for the last time after the full
timeout has passed.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Check error bits and save the exception bit when polling card busy.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Make card_busy_detect() accumulate all response error bits. Later patches
will make use of this.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Recovery is simpler to understand if it is only used for errors. Create a
separate function for card polling.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

For blk-mq, add support for completing requests directly in the ->done
callback. That means that error handling and urgent background operations
must be handled by recovery_work in that case.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Add CQHCI initialization and implement CQHCI operations for Intel GLK.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds CMDQ support for command-queue compatible
hosts.

Command queue is added in eMMC-5.1 specification. This
enables the controller to process upto 32 requests at
a time.

Adrian Hunter contributed renaming to cqhci, recovery, suspend
and resume, cqhci_off, cqhci_wait_for_idle, and external timeout
handling.
Signed-off-by: NAsutosh Das <asutoshd@codeaurora.org>
Signed-off-by: NSujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: NKonstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: NVenkat Gopalakrishnan <venkatg@codeaurora.org>
Signed-off-by: NSubhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: NRitesh Harjani <riteshh@codeaurora.org>
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Add CQE support to the block driver, including:
    - optionally using DCMD for flush requests
    - "manually" issuing discard requests
    - issuing read / write requests to the CQE
    - supporting block-layer timeouts
    - handling recovery
    - supporting re-tuning

CQE offers 25% - 50% better random multi-threaded I/O.  There is a slight
(e.g. 2%) drop in sequential read speed but no observable change to sequential
write.

CQE automatically sends the commands to complete requests.  However it only
supports reads / writes and so-called "direct commands" (DCMD).  Furthermore
DCMD is limited to one command at a time, but discards require 3 commands.
That makes issuing discards through CQE very awkward, but some CQE's don't
support DCMD anyway.  So for discards, the existing non-CQE approach is
taken, where the mmc core code issues the 3 commands one at a time i.e.
mmc_erase(). Where DCMD is used, is for issuing flushes.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Define and use a blk-mq queue. Discards and flushes are processed
synchronously, but reads and writes asynchronously. In order to support
slow DMA unmapping, DMA unmapping is not done until after the next request
is started. That means the request is not completed until then. If there is
no next request then the completion is done by queued work.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Until mmc has blk-mq support fully implemented and tested, add a parameter
use_blk_mq, set to true if config option MMC_MQ_DEFAULT is selected, which
it is by default.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Add error-handling comments to explain what would also be done for blk-mq
if it used the legacy error-handling.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>

Make mmc_pre_req() and mmc_post_req() available to the card drivers. Later
patches will make use of this.
Signed-off-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NLinus Walleij <linus.walleij@linaro.org>