Add support for EXTMUTE in Zoom2 machine driver. This is necessary
to further reduce pop noise problem. Signal EXTMUTE is connected to
signal GPIO 153 in Zoom2 board.

In addition, change ramp delay value to 3 (218/161/109 ms). With
previous ramp delay value, pop noise was louder. With a longer value
the beep tone can be observed.
Signed-off-by: NJorge Eduardo Candelaria <x0107209@ti.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Voice interface of twl4030 codec supports: CBM_CFM and
CBS_CFS. It doesn't support CBS_CFM.
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Acked-By: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add support for Zoom2 board. Zoom2 machine driver
connects both codec DAIs (audio and voice) to omap3
McBSP ports in the following way:

  HiFi <-> McBSP2
 Voice <-> McBSP3

The zoom2 driver has the following DAPM widgets:
* Ext Mic: MAINMIC, SUBMIC (with bias)
* Ext Spk: HFL, HFR
* Headset Stereophone: HSOL, HSOR
* Headset Mic: HSMIC (with bias)
* Aux In: AUXL, AUXR
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

With this patch the initial headset pop-removal related values are
configured for the twl4030 codec (ramp delay and sysclk).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Connect twl4030 voice DAI to McBSP3 in sdp3430 machine driver.
Voice DAI init function enables corresponding interface by
writting directly to VOICE_IF codec register.
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Acked-by: NPeter Ujflausi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add Voice DAI to support the PCM voice interface of the twl4030 codec.

The PCM voice interface can be used with 8-kHz(voice narrowband) or
16-kHz(voice wideband) sampling rates, and 16bits, and mono RX and mono
TX or stereo TX.

The PCM voice interface has two modes
 - PCM mode1 : This uses the normal FS polarity and the rising edge of
               the clock signal.
 - PCM mode2 : This uses the FS polarity inverted and the falling edge
               of the clock signal.

If the system master clock is not 26MHz or the twl4030 codec mode is not
option2, the voice PCM interface is not available.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Headset was declared previously as a Headphone widget connecting
HSMIC and HSOL/HSOR pins of TWL4030 codec in SDP430 machine driver.
The capture path becomes invalid as the Headphone widget is not a
valid input endpoint.

Instead of that, the Headset is declared as separate Microphone
and Headphone widgets. Current patch modifies audio map:

- Headset Mic: HSMIC with bias
- Headset Stereophone: HSOL, HSOR
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Move headset jack registration to the codec/machine specific
initialization. Having the jack registration in machine init
causes that the jack device gets initialized but not registered
since the sound card is registered before the jack. Moving jack
registration to device initialization will register the jack
device along with all other devices associated to the card when
the card is registed. As a consequence of jack device registered
properly, the jack is detected as an input device.
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add headset jack detection for SDP3430 boards using SoC jack
reporting interface. Headset detection on SDP3430 board is
achieved through TWL4030 GPIO_2 pin.
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add DAPM machine domain widgets to SDP3430 machine driver.
Interconnection:
* Ext Mic: MAINMIC, SUBMIC
* Ext Spk: HFL, HFR
* Headset Jack: HSMIC, HSOL, HSOR
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch replaces "snd_soc_machine" structure by "snd_soc_card" in
SP3430 driver. This change is needed in SDP3430 driver to reflect
changes introduced by "ASoC: Rename snd_soc_card to snd_soc_machine" patch
(87506549).
Signed-off-by: NMisael Lopez Cruz <x0052729@ti.com>
Acked-by: NJarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

As part of the deprecation of snd_soc_device push the registration of
the platform down into the card structure.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This patch add ASoC support for TI SDP3430. It's based on Gumstix
Overo SoC code by Steve Sakoman.
Signed-off-by: NMisael Lopez Cruz <mesak82@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

One of the issues with the ASoC v1 API which has been addressed in the
ASoC v2 work that Liam Girdwood has done is that the ALSA card provided
by ASoC is distributed around the ASoC structures. For example, machine
wide data such as the struct snd_card are maintained as part of the
CODEC data structure, preventing the use of multiple codecs. This has
been addressed by refactoring the data structures so that all the data
for the ALSA card is contained in a single structure snd_soc_card which
replaces the existing snd_soc_machine and snd_soc_device.

Begin the process of backporting this by renaming struct snd_soc_machine
to struct snd_soc_card, better reflecting its function and bringing it
closer to standard ALSA terminology.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>