alloc failures already get standardized OOM
messages and a dump_stack.

For the affected mallocs around these OOM messages:

Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extend the bus interface with chip identifier and revision. This
will be used when certain devices need special handling in the
driver.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NPiotr Haber <phaber@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Statistics were tracked by bus driver while it is to be tracked
per ifp/netdev.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The use of the function brcmf_proto_hdrpull() is moved to the
common part of the driver and consequently it can be removed
from the bus interface.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bus interface provided a wrapper function to pass a single
packet to the common driver part filling a skb queue with one
packet. For clarity the caller now sets up the skb queue and
call the rx bus interface function.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upon unloading the brcmfmac module the USB firmware should be reset
as the device remains powered. The reset assures a known device
state when a new brcmfmac driver load is being done.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When USB device gets removed rx complete comes with 0-length
packets. Do not refill those packets. In some rare cases it can
cause infinite loop.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The call to brcmf_dbg(ERROR, ...) only resulted in a log message
when compiled with -DDEBUG. Error messages are valuable for resolving
issues so this patch replaces it with brcmf_err(...) so they always
end up in the log.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rework the bus interface between common driver part and bus-specific
driver part. It prepares for adding tracing in bus-specific callback
functions.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This avoids build failures on some architectures...
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Acked-by: NArend van Spriel <arend@broadcom.com>

Removing obsolete functions and prototypes. Moving (and renaming)
defines to place with similar definitions. Removing unnecessary
includes.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add support for usb suspend/resume.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Clean code related to firmware download routines. Remove obsolete
delay and increase delay after reset command.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add USB log level and update and add log messages in usb module.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

reuse ioctl waiting method.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

in brcmf_usb_probe_cb only return code ENOLINK was seen as an
error. This is wrong, all error codes should be returned to usb
subsystem.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_usb_tx_complete now calls brcmf_txcomplete to correct
eapol counter.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

firmware control packets over usb are async acked. This is
awaited for by using interruptible wait. This can be
interrupted by signal which results in undesirable behavior.
Instead wait_event_timeout is used.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On a usb error the lock bit should be cleared.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

clean up code.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

For suspend/resume it is necessary to store firmware in memory.
In order to support multiple usb dongles at the same time a linked
list of firmwares was created.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes bug where driver frees resources twice when
an exception occurs.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes usage of some of the local data in the usb
host interface driver. This is a step in the preperation to
support multiple USB devices.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug where rx buffer does not get refilled if the
packet received has an rx protocol error.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enable tx flow control for USB host interface.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added usb device id to list of supported devices. 43143 is a new
802.11n single stream device.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Added usb device id to list of supported devices. 43242 is the new
802.11n 2x2 MIMO device.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

brcmf_usb_tx_ctlpkt sends message using brcmf_usb_send_ctl then
clears boolean and waits for boolean to be set (by another
thread). This can result in situation where flag gets cleared
while result was already received. First clearing the flag and
then sending the data will prevent this.

Reviewed-by: Arend Van Spriel (arend@broadcom.com)
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On both rx and tx there is was a race condition on the queueing
of usb requests. When for example frame gets submitted it is
possible that complete function gets called even before
usb_submit_urb() returns. As a result it is possible that usb
requests get losts, which was noticed on OMAP4 pandaboard
platform. This patch fixes the race condition.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

URB_ZERO_PACKET should only be set or bulk OUT and this condition
is checked with a WARN_ON in usb_submit_urb(). This patch fixes
brcmfmac to get rid of this warning filling the logs.
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The USB part of the brcmfmac did a dev_kfree_skb() that resulted
in a warning in net/core/skbuff.c:

Jul 11 04:53:33 lb-bun-10 kernel: [53282.667745] WARNING: at
net/core/skbuff.c:490 skb_release_head_state+0xcc/0xe0()

The brcmutil modules provides brcmu_pkt_buf_free_skb() which takes
the context into account. This patch makes use of this function
instead of dev_kfree_skb().
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware is more than 300KB big and you should not use kmalloc for
such big allocations. This allocation with kmalloc failed on my mips
based device (BCM47186).
Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de>
Acked-by: NFranky Lin <frankyl@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix missing comma.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Reported-by: NWu Fengguang <wfg@linux.intel.com>

Hub-initiated LPM is not good for USB communications devices.  Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.

If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data.  Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.

The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host.  In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.

Set the disable_hub_initiated_lpm flag for for all USB communications
drivers.  I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The primary net device was registered with a primary mac address and
upon IFUP it was set to match the actual mac address from the device.
This patch changes that and moves the brcmf_add_if() call to the common
part of the driver.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The module init function of brcmfmac calls init functions for SDIO and
USB doing driver registration. This patch removes terminating the module
init when a driver registration for one host interface fails.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The usb code defines a structure for counting statistics. However,
it should use the statistics entry provided in brcmf_bus as that is
exposed to the net_device. The usb private statistics counter only
remains with counters for control packets between driver and usb
device.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Several fields in this structure are only written once or not used
at all. Remaining two fields have been moved and brcmf_usb_attrib
definition has been removed.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NKan Yan <kanyan@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In brcmf_usb_up() the variable devinfo was checked for being
a NULL pointer, but this can not happen. Also the check was done
after dereferencing the pointer. This patch removes the check.
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: NFranky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: NKan Yan <kanyan@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also don't use so generic BRCMF_USB_FW_NAME as we may need different
firmwares in the future.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>