Use at91_nand_enable(), at91_nand_disable() to manipulate enable_pin.
No functional changes.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=4053Singed-off-by: NMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This driver did not control NCE signal during normal operations (only
enable NCE on probing and disable NCE on removing).  This patch make
NCE signal inactive on idle state.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The sam926x docs allegedly don't list an "ECC_PARITY" field, and the 
header files in the upstream kernel don't have it either.

Masking with it was useless anyway, so just remove it.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is a patch to use the hardware ECC controller of
the AT91SAM9260 and AT91SAM9263 for the AT91 nand.
On AT91 NAND, there's now a choice between ECC soft,
ECC hard or no ECC (for debug).

It has been tested on AT91SAM9263 with 8 bits large
and small page NAND.
Signed-off-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

With modern systems using bus-hold instead of bus pull-up, it can
often lead to erroneous reporting of NAND devices where there are
none. Do a double probe to ensure that the result we got the first
time is repeatable, and if it is not then return that there is no
chip there.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Add support to disable ECC checking for a given chip
when passed by the board via the platform data.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Add support for the ECC layout to be passed via the
platform data specified by the board.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

If a block's ecc field is all 0xff, then ignore the ECC
correction. This is for systems where some of the blocks,
such as the initial cramfs are written without ECC and
need to be loaded on start.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This adds support for using large page NAND devices
with the S3C24XX NAND controller. This also adds the
file Documentation/arm/Samsung-S3C24XX/NAND.txt to
describe the differences.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Commit 03680b1e incorrectly
was assuming S3C2410_NFCONF was being used to select the
NAND chip. Fix this error by ising the sel_reg.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Using current driver elbc sometimes hangs during nand write. Reading back
last byte helps though (thanks to Scott Wood for the idea).
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This patch sets mtd->name to the platform bus ID in the plat_nand
driver, so that you can specify partitions readily with mtdparts=.

Currently it relies on nand_base filling in the name from the device,
which results in names like "NAND 256MiB 3,3V 8-bit", that you can't
use with cmdlineparts.
Signed-off-by: NHamish Moffatt <hamish@cloud.net.au>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Fix a race condition in fsl_elbc_run_command
Fix incorrect usage of clearbits32 that bashed option register
Remove work around for bashed register
Signed-off-by: NMike Hench <mhench@elutions.com>
Acked-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Currently fsl_elbc_nand doesn't initialize mtd->name, and this causes
nand_get_flash_type() to assign name that is equal to chip type, like
this:

   root@b1:~# cat /proc/mtd
   dev:    size   erasesize  name
   mtd0: 00800000 00010000 "fe000000.flash"
   mtd1: 02000000 00004000 "NAND 32MiB 3,3V 8-bit"

mtd0 is physmap_of flash (normal name), and mtd1 is fsl_elbc_nand.

Despite inconsistency, with mtd name like this specifying paritions
from the kernel command line becomes a torture (though, I didn't tried
and not sure if mtdparts= can handle spaces at all). Plus, this causes
real bugs when multiple fsl_elbc_nand chips registered.

With this patch applied fsl_elbc_nand chip will have proper name:

   root@b1:~# cat /proc/mtd
   dev:    size   erasesize  name
   mtd0: 00800000 00010000 "fe000000.flash"
   mtd1: 02000000 00004000 "e0600000.flash"

p.s. We can't use priv->dev->bus_id as in physmap_of, because
fsl_elbc_nand pretends to be a localbus controller, so its bus_id is
"address.localbus", which is incorrect and thus will also not work
for multiple chips.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is very simple driver, NAND is connected through localbus,
and User-Programmable Machine is doing various adjustments to
speak NAND. No special efforts needed to do read and write cycles,
though to control ALE and CLE phases, we ask UPM to generate exact
pre-programmed signals on the localbus lines.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is preliminary since:

1. It supports only _one_ chip select at the moment. As there is no
   existing platforms available using two chip selects of the NAND
   controller, it shall really not include code for supporting the
   2nd chip select for now, as such code cannot be verified.

2. It resorts to the default and simpliest memory based badblock
   table

3. Only limited types of nand flash are currently supported. Most
   PXA3xx processors come with on-chip NAND flash dies, so there
   isn't much flexibility for other types of NAND.

4. The NAND controller should be configured to detect the device's
   ID, thus making it difficult to use nand_scan_ident() to assist
   the detection process (though it's not impossible)

TODO: fix all the above limitations of cuz :-)
Signed-off-by: Neric miao <eric.miao@marvell.com>
Cc: Sergey Podstavin <spodstavin@ru.mvista.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Previously, a READ command was erroneously issued rather than SEQIN.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The part_probes[] should be static.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NJörn Engel <joern@logfs.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Since 43cc71ee, the platform modalias is
prefixed with "platform:".  Add MODULE_ALIAS() to the hotpluggable MTD NAND
platform drivers, to re-enable auto loading.

NOTE: at91_nand for some reason disallows modular builds.  I'm assuming that's
just an oversight that will be fixed.

[dbrownell@users.sourceforge.net: minor fix]
Signed-off-by: NKay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

I found this while I was looking how the rs_lib is working.  The rs_decoder is
initialized _after_ the nand core code read the BBT table and _after_ the
partition table has been added.  The driver has a private BBT description
which is in located in flash data so we Ooops if there is a bit flip _or_ if a
bit flips while reading the partition table.

This patch moves the initialization of the rs_lib before the first possible
access by nand core.
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jörn Engel <joern@wh.fh-wedel.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Make the needlessly global part_probes[] static.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Acked-by: NMart Raudsepp <mart.raudsepp@artecdesign.ee>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

This is needed to support other localbus peripherals, such as
NAND on FSL UPM.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This has been forgotten in commit f5bbdacc ("[MTD] NAND Modularize
read function") and nobody compiled the driver.
Signed-off-by: NSebastian Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Joern Engel <joern@wh.fh-wedel.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Reviewed-by: NTzachi Perelstein <tzachi@marvell.com>
Acked-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Implements kernel command line partitioning support for the CS5535/CS5536 chipsets driver.

For that the following is done:

* cs553x_cleanup(): try the cleanup for all chip selects to not leak memory
* Assign a unique name for each chip select to be separately addressable in the command line mtd-id portion(s)
* Use the already defined PIN_OPT_IDE constant where appropriate for readability
* Include command line partitioning support when CONFIG_MTD_PARTS is set
Signed-off-by: NMart Raudsepp <mart.raudsepp@artecdesign.ee>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NNick Spence <nick.spence@freescale.com>
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

There is no suspend/resume operation in NFC driver at all, currently.
Signed-off-by: NBryan Wu <bryan.wu@analog.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

With CONFIG_MTD_PARTITIONS not set, got this:
drivers/mtd/nand/plat_nand.c:113: warning: unused variable 'pdata'
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Call parse_mtd_partitions before checking board's partition_info, so
that "mtdparts=" option can override board's default setting.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The single-bit error correction was, well, incorrect. For determing which
bit to correct it was using P1' P2' P4' P8' instead of P1 P2 P4 P8, and
it was using P16' P32' P64' P128' P256' P512' P1024' P2048' instead of
P16 P32 P64 P128 P256 P512 P1024 P2048.
Signed-off-by: NMatt Reimer <mreimer@vpop.net>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

If there were multiple bit errors in the data s3c2410_nand_correct_data()
was returning 0 (no error) instead of -1, so the upper layers (like JFFS2)
would not know the data is corrupt.
Signed-off-by: NMatt Reimer <mreimer@vpop.net>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Some hardware, such as the enhanced local bus controller used on some
mpc83xx chips, does ecc transparently when reading and writing data, rather
than providing a generic calculate/correct mechanism that can be exported to
the nand subsystem.

The subsystem should not BUG() when calculate, correct, or hwctl are
missing, if the methods that call them have been overridden.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Driver for the device bus NAND controller in the Marvell Orion family
of ARM SoCs.
Signed-off-by: NTzachi Perelstein <tzachi@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Acked-by: NJörn Engel <joern@logfs.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Plumbing for NAND connected via localbus on PA Semi PWRficient-based
boards.

From: Egor Martovetsky <egor@pasemi.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Ensure the nFCE line is de-asserted over suspend and
then re-initialised when the system resumes. This is
to ensure that the NAND is kept in lowest power mode
over suspend (power settings are only specified for
nFCE inactive) as well as fixing the Simtec Osiris
which relies on nFCE being inactive.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>