Made *ocp2scp_usb_phy_phy_48m* as the main_clk for ocp2scp.
Since this ocp2scp module does not have any fck but does have a
single opt_clock, it is added as the main_clk for ocp2scp. Also
removed phy_48m as the optional clock since it is now made as the
main clock. By this the driver need not enable/disable phy_48m clk
separately and runtime_get/runtime_put will take care of that.

Cc: Benoît Cousson <b-cousson@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Acked-by: NBenoît Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

ocp2scp_usb_phy was missing the address space data and thus
the sysconfig was not populated either.
The usb_host_hs address space was wrong.

Fix both of them and add the missing sysconfig entry.
Reported-by: NKishon Vijay Abraham <kishon@ti.com>
Signed-off-by: NBenoit Cousson <b-cousson@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

SAD2D stands for the die to die interface, and is used for communicating
with the optional stacked modem. This hwmod is added in preparation for
the d2d_idle move from pm34xx.c to hwmod data.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
[paul@pwsan.com: SAD2D presumably doesn't exist on non-OMAP34xx/OMAP36xx,
 so only add it to the OMAP34xx/OMAP36xx lists]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

For a reset sequence to complete cleanly, a module needs its
associated clocks to be enabled, otherwise the timeout check
in prcm code can print a false failure (failed to hardreset)
that occurs because the clocks aren't powered ON and the status
bit checked can't transition without them.
Signed-off-by: NOmar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Some IP blocks might not be using/controlling more than one
reset line, this check loosens the restriction to fully use
hwmod framework for those drivers.

E.g.: ipu has reset lines: mmu_cache, cpu0 and cpu1.
- As of now cpu1 is not used and hence (with previous check) the
  IP block isn't fully enabled by hwmod code.
- Usually ipu and dsp processors configure their mmu module first
  and then enable the processors, this involves:
    * Deasserting mmu reset line, and enabling the module.
    * Deasserting cpu0 reset line, and enabling the processor.
  The ones portrayed in this example are controlled through
  rproc_fw_boot in drivers/remoteproc/remoteproc_core.c

While at it, prevent _omap4_module_disable if all the hardreset
lines on an IP block are not under reset.

This will allow the driver to:
  a. Deassert the reset line.
  b. Enable the hwmod through runtime PM default callbacks.
  c. Do its usecase.
  d. Disable hwmod through runtime PM.
  e. Assert the reset line.
Signed-off-by: NOmar Ramirez Luna <omar.luna@linaro.org>
[paul@pwsan.com: updated to apply]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On OMAP4 most modules/hwmods support module level context status. On
OMAP3 and earlier, we relied on the power domain level context status.
Identify all modules that don't support 'context_offs' by adding a
flag bit, HWMOD_OMAP4_NO_CONTEXT_LOSS_BIT.  Rest have a valid
'context_offs' populated in .prcm structure already.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
[paul@pwsan.com: add flag bit rather than overloading .context_offs;
 update changelog message]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Currently hwmod only provides the offset for the context lose
register, and if we attempt to share the same register between two or
more hwmods, the resulting context loss counts get wrong. Thus, we
need a way to specify which bits are used for the context loss
information for each.  This is accomplished by adding a new field to
the omap4 prcm struct, 'lostcontext_mask', which specifies a bit-mask
to use for filtering the register.

Mark the affected hwmods appropriately.  'l4_abe' hwmod uses the
LOSTMEM_AESSMEM bit of RM_ABE_AESS_CONTEXT register, as l4_abe doesn't
have its own dedicated register for this purpose. This register is
shared with 'aess' hwmod, thus both hwmods must also specify which
bits of the register are used for them.

This patch only adds the hwmod data, but a future patch should add
code support such that only the specified bits are read and cleared by
the context lose counter update code. If a hwmod doesn't specify
'lostcontext_mask' (default behavior), the whole contents of the
context register should be used without any filtering.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
[paul@pwsan.com: updated to apply after conversion to use flag bit for
 missing module context-loss register; combined data and code patches;
 dropped code change due to serial driver breakage]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

On OMAP4, there is no support to read previous logic state
or previous memory state achieved when a power domain transitions
to RET. Instead there are module level context registers.

In order to support the powerdomain level logic/mem_off_counters
on OMAP4, instead use the previous power state achieved (RET) and
the *programmed* logic/mem RET state to derive if a powerdomain lost
logic or did not.

If the powerdomain is programmed to enter RET state and lose logic
in RET state, knowing that the powerdomain entered RET is good enough
to derive that the logic was lost as well, in such cases.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
[paul@pwsan.com: removed dependency on functional power state series for now;
 bumped copyright date]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The decision was made a few months ago to allow struct omap_hwmod
records and struct clk records to omit clockdomain information if the
clockdomain is not software-controllable.  See for example commit
868c157d ("ARM: OMAP2+: hwmod: remove
prm_clkdm, cm_clkdm; allow hwmods to have no clockdomain").

So convert an existing pr_warning() to a pr_debug() (regarding missing
clockdomains in clocks), and add a pr_debug() for missing hwmod
clockdomains.  It's still useful to enable these messages for
debugging, since missing clockdomains can cause hard-to-debug problems
with power management; see for example commit
6c4a057b ("ARM: OMAP4: clock data:
Force a DPLL clkdm/pwrdm ON before a relock").
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

We're no longer requiring struct omap_hwmod records to contain a
clockdomain.  So we shouldn't return -EINVAL any more from
_omap4_wait_target_disable() or _omap4_wait_target_ready() if there's
no clockdomain defined, since that just gets passed back to the
caller.  This can result in pointless warnings under the relaxed data
format.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>

This API is meant to be an interface to hwmod assert/deassert
function, omap devices can call them through their platform data to
control their reset lines, they are expected to know the name of the
reset line they are trying to control.
Signed-off-by: NOmar Ramirez Luna <omar.luna@linaro.org>
[paul@pwsan.com: tweaked some documentation; fixed CodingStyle issue]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Several hwmod function prototypes appear to not have an implementation
because the corresponding functions were removed or renamed.
Those prototypes are unneeded anymore - remove them.
Signed-off-by: NIgor Grinberg <grinberg@compulab.co.il>
[paul@pwsan.com: tweaked subject]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Conflicts:
	arch/arm/mach-omap2/clkt34xx_dpll3m2.c
	arch/arm/mach-omap2/clkt_clksel.c
	arch/arm/mach-omap2/clock.c

From Paul Walmsley <paul@pwsan.com>:

AM33xx hwmod data and miscellaneous clock and hwmod fixes.  AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.

These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.

smatch and string-wrapping cleanups for the OMAP subarch code.

These changes fix some of the more meaningful warnings that smatch
returns for the OMAP subarch code, and unwraps strings that are
wrapped at the 80-column boundary, to conform with the current
practice.

Basic build, boot, and PM logs are available here:

http://www.pwsan.com/omap/testlogs/warnings_a_cleanup_3.7/20120912025927/

The new common clk framework includes basic definitions for mux and
divider clocks.  These definitions depend on shift and width values
instead of the pre-computed masks that the OMAP/AM33XX clk framework
has traditionally used when accessing the register to control the
mux or divisor.

To ease this transition the masks are left intact and
the width field is simply added alongside the shift and mask data.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

The new common clk framework includes basic definitions for mux and
divider clocks.  These definitions depend on shift and width values
instead of the pre-computed masks that the OMAP clk framework has
traditionally used when accessing the register to control the mux or
divisor.

To ease this transition the masks are left intact and the width field is
simply added alongside the shift and mask data.
Signed-off-by: NMike Turquette <mturquette@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

While we move to Common Clk Framework (CCF), direct deferencing of struct
clk wouldn't be possible anymore. Hence get rid of all such instances
in the current clock code and use macros/helpers similar to the ones that
are provided by CCF.

While here also concatenate some strings split across multiple lines
which seem to be needed anyway.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
[paul@pwsan.com: simplified some compound expressions; reformatted some
 messages]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Mike Turquette <mturquette@linaro.org>

Moving to Common clk framework for OMAP would mean we no longer use
internal lookup mechanism like omap_clk_get_by_name().
get rid of all its usage mostly from hwmod and omap_device
code.

Moving to clk_get() also means the respective platforms
need the clkdev tables updated with an entry for all clocks
used by hwmod to have clock name same as the alias.

Based on original changes from Mike Turquette.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
[paul@pwsan.com: removed IS_ERR_OR_NULL() conversion (rmk comment);
 restricted omap_96m_alwon_fck_3630 to OMAP36xx; added missing AM35xx
 clock aliases for emac_fck, emac_ick, vpfe_ick, vpfe_fck; added
 aliases rng_ick and several emulation clocks]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

As part of Common Clk Framework (CCF) the clk_enable() operation
was split into a clk_prepare() which could sleep, and a clk_enable()
which should never sleep. Similarly the clk_disable() was
split into clk_disable() and clk_unprepare(). This was
needed to handle complex cases where in a clk gate/ungate
would require a slow and a fast part to be implemented.
None of the clocks below seem to be in the 'complex' clocks
category and are just simple clocks which are enabled/disabled
through simple register writes.
Most of the instances also seem to be called in non-atomic
context which means its safe to move all of those from
using a clk_enable() to clk_prepare_enable() and clk_disable() to
clk_disable_unprepare().

For some others, mainly the ones handled through the hwmod framework
there is a possibility that they get called in either an atomic
or a non-atomic context.

The way these get handled below work only as long as clk_prepare
is implemented as a no-op (which is the case today) since this gets
called very early at boot while most subsystems are unavailable.
Hence these are marked with a *HACK* comment, which says we need
to re-visit these once we start doing something meaningful with
clk_prepare/clk_unprepare like doing voltage scaling or something
that involves i2c.

This is in preparation of OMAP moving to CCF.

Based on initial changes from Mike Turquette.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Remove unnecessary includes of plat/clock.h from the OMAP SPI
controller drivers.  These need to be removed to build multi-subarch
ARM kernels which include these drivers.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: NGrant Likely <grant.likely@secretlab.ca>

For OMAP4, the dmtimers are located in the Wake-up, ABE and Peripheral (PER)
power domains. Hence, when the dmtimer is configured to use the "timer_sys_ck"
as its functional clock the actual clock used is different depending on whether
the clock is in the Wake-up, ABE or PER domain. So when we look-up the dmtimer's
"timer_sys_ck" we need to specify the timer device name as well as clock alias
to find the right clock.

Currently, the device names for the timers have the format "omap_timer.X" where
X is the timer instance number. When using to device tree, the format of the
device name created by device-tree is different and has the format
"<reg-address>.<device-name>" (this is assuming that the device-tree "reg"
property is specified). This causes the look-up for the OMAP4 "timer_sys_ck" to
fail. To fix this add new timer clock alias for using device-tree.

Please note that adding a 2nd set of clock aliases for the same clocks to only
temporary until device-tree migration is complete. Then we can remove the legacy
aliases. Hence, I have marked the legacy aliases with a "TODO" to remove them.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: updated to apply]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

Add AM335x cpu0 clock entry to the corresponding clock data file. This
is useful in getting the correct mpu clock pointer to change the cpu
frequency in cpufreq driver.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
[paul@pwsan.com: changed patch subject]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

These clkdev aliases should make it possible to remove the
cpu_is_omap*() calls and the omap_device*() call from
drivers/cpufreq/omap-cpufreq.c during the next merge window.  Those
are interfering with multi-subarch ARM kernels.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: NKevin Hilman <khilman@ti.com>

The platform device name "usbhs_tll" is added for the functional,
interface and channel clocks of the TLL module.
Signed-off-by: NKeshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: NPartha Basak <parthab@india.ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

In commit c59b537d (ARM: OMAP2+: Simplify dmtimer clock aliases) new clock
aliases were added for OMAP2+ devices. For OMAP2420, I incorrectly set the
clock flag as CK_243X instead of CK_242X. This did not introduce a regression
as the clock flags are not checked for OMAP2 devices. This also explains why
I did not catch this when testing on OMAP2420.

Fix the clock flags for these aliases for correctness.
Signed-off-by: NJon Hunter <jon-hunter@ti.com>

The file is currently called 'clock3xxx_data.c', so this comment is
out of date.
Signed-off-by: NMichael Jones <michael.jones@matrix-vision.de>
[paul@pwsan.com: wrote changelog]
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

From Paul Walmsley <paul@pwsan.com>:

AM33xx hwmod data and miscellaneous clock and hwmod fixes.  AM33xx
should now boot on mainline after this is applied, according to
Vaibhav.

These fixes are needed to fix non-omap build breakage for
twl-core driver and to fix omap1_defconfig compile when
led driver changes and omap sparse IRQ changes are merged
together. Also fix warnings for omaps not using pinctrl
framework yet.

Merge of the LED related changes with omap sparse IRQ and
hardware.h related changes causes a build issue otherwise:

arch/arm/mach-omap1/board-h2.c:319: error: implicit declaration of function ‘OMAP_MPUIO’
arch/arm/mach-omap1/board-h2.c:319: error: initializer element is not constant
arch/arm/mach-omap1/board-h2.c:319: error: (near initialization for ‘h2_gpio_led_pins[1].gpio’)
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable pinctrl dummy states for all OMAP platforms that don't
populate DT. This allows drivers to be converted to pinctrl
and not generate new warnings on platforms that do not provide
pinctrl data. These platforms already have pinmuxes configured
before the drivers probe.
Signed-off-by: NMatt Porter <mporter@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Commit 7d7e1eba (ARM: OMAP2+: Prepare for irqs.h removal) broke
compile for non-omap as include plat/cpu.h was added. This header
was indirectly included earlier when SPARSE_IRQ was not set, but
does not exist on most platforms.

Fix the problem by removing the cpu_is_omap usage that should
not exist in drivers at all. We can do this by adding proper
clock aliases for the twl-core.c drivers, and drop separate
handling for cases when clock framework is not available as
the behaviour will stay the same.

Note that we need to add a platform device to avoid using the
i2c provided names that may be different on various omaps.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Pull mfd fixes from Samuel Ortiz:
 "This is the remaining MFD fixes for 3.6, with 5 pending fixes:

   - A tps65217 build error fix.
   - A lcp_ich regression fix caused by the MFD driver failing to
     initialize the watchdog sub device due to ACPI conflicts.
   - 2 MAX77693 interrupt handling bug fixes.
   - An MFD core fix, adding an IRQ domain argument to the MFD device
     addition API in order to prevent silent and potentially harmful
     remapping behaviour changes for drivers supporting non-DT
     platforms."

* tag 'mfd-for-linus-3.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
  mfd: MAX77693: Fix NULL pointer error when initializing irqs
  mfd: MAX77693: Fix interrupt handling bug
  mfd: core: Push irqdomain mapping out into devices
  mfd: lpc_ich: Fix a 3.5 kernel regression for iTCO_wdt driver
  mfd: Move tps65217 regulator plat data handling to regulator

Pull pwm fixes from Thierry Reding:
 "While this comes a bit later than I had wished, both patches are
  rather minor and touch only new drivers so I think these are still
  safe for merging."

* tag 'for-3.6-rc6' of git://gitorious.org/linux-pwm/linux-pwm:
  pwm: pwm-tiehrpwm: Fix conflicting channel period setting
  pwm: pwm-tiecap: Disable APWM mode after configure

Pull scsi target fixes from Nicholas Bellinger:
 "Here is the current set of target-pending fixes headed for v3.6-final

  The main parts of this series include bug-fixes from Paolo Bonzini to
  address an use-after-free bug in pSCSI sense exception handling, along
  with addressing some long-standing bugs wrt the handling of zero-
  length SCSI CDB payloads also specific to pSCSI pass-through device
  backends."

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  target: go through normal processing for zero-length REQUEST_SENSE
  target: support zero allocation length in REQUEST SENSE
  target: support zero-size allocation lengths in transport_kmap_data_sg
  target: fail REPORT LUNS with less than 16 bytes of payload
  target: report too-small parameter lists everywhere
  target: go through normal processing for zero-length PSCSI commands
  target: fix use-after-free with PSCSI sense data
  target: simplify code around transport_get_sense_data
  target: move transport_get_sense_data
  target: Check idr_get_new return value in iscsi_login_zero_tsih_s1
  target: Fix ->data_length re-assignment bug with SCSI overflow

Pull power management fixes from Rafael J. Wysocki:
 "Three ACPI device power management fixes related to checking and
  setting device power states."

* tag 'pm-for-3.6-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / PM: Use KERN_DEBUG when no power resources are found
  ACPI / PM: Fix resource_lock dead lock in acpi_power_on_device
  ACPI / PM: Infer parent power state from child if unknown, v2

Pull a btrfs revert from Chris Mason:
 "My for-linus branch has one revert in the new quota code.

  We're building up more fixes at etc for the next merge window, but I'm
  keeping them out unless they are bigger regressions or have a huge
  impact."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  Revert "Btrfs: fix some error codes in btrfs_qgroup_inherit()"

Pull more sound fixes from Takashi Iwai:
 "Yet more (a bunch of) small fixes that slipped from the previous pull
  request.  Most of commits are pending ASoC fixes, all of which are
  fairly trivial commits."

* tag 'sound-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ASoC: wm8904: correct the index
  ALSA: hda - Yet another position_fix quirk for ASUS machines
  ASoC: tegra: fix maxburst settings in dmaengine code
  ASoC: samsung dma - Don't indicate support for pause/resume.
  ASoC: mc13783: Remove mono support
  ASoC: arizona: Fix typo in 44.1kHz rates
  ASoC: spear: correct the check for NULL dma_buffer pointer
  sound: tegra_alc5632: remove HP detect GPIO inversion
  ASoC: atmel-ssc: include linux/io.h for raw io
  ASoC: dapm: Don't force card bias level to be updated
  ASoC: dapm: Make sure we update the bias level for CODECs with no op
  ASoC: am3517evm: fix error return code
  ASoC: ux500_msp_i2s: better use devm functions and fix error return code
  ASoC: imx-sgtl5000: fix error return code