'queue_io' is set so that IO is queued while paths are being
initialized.  Clear queue_io in __choose_pgpath if there are no valid
paths, since there are obviously no paths that can be initialized.
Otherwise IOs to the device will back up.
Signed-off-by: NBenjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

pg_ready() is not comprehensive in its logic and only serves to
obfuscate code.  Replace pg_ready() with the appropriate logic in
multipath_map().
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Commit e8099177 ("dm mpath: push back requests instead of queueing")
modified multipath_busy() to return true if !pg_ready().  pg_ready()
checks the current state of the multipath device and may return false
even if a new IO is needed to change the state.

Bart Van Assche reported that he had multipath IO lockup when he was
performing cable pull tests.  Analysis showed that the multipath
device had a single path group with both paths active, but that the
path group itself was not active.  During the multipath device state
transitions 'queue_io' got set but nothing could clear it.  Clearing
'queue_io' only happens in __choose_pgpath(), but it won't be called
if multipath_busy() returns true due to pg_ready() returning false
when 'queue_io' is set.

As such the !pg_ready() check in multipath_busy() is wrong because new
IO will not be sent to multipath target and the multipath state change
won't happen.  That results in multipath IO lockup.

The intent of multipath_busy() is to avoid unnecessary cycles of
dequeue + request_fn + requeue if it is known that the multipath
device will requeue.

Such "busy" situations would be:
  - path group is being activated
  - there is no path and the multipath is setup to requeue if no path

Fix multipath_busy() to return "busy" early only for these specific
situations.
Reported-by: NBart Van Assche <bvanassche@acm.org>
Tested-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.15

Add DM core support for disabling WRITE SAME on first failure to both
request-based and bio-based targets.  The need to disable WRITE SAME
stems from SCSI enabling it by default but then disabling it when it
fails.  When SCSI does this it returns "permanent target failure, do
not retry" using -EREMOTEIO.  Update DM core to only disable WRITE SAME
on failure if the returned error is -EREMOTEIO.

Commit f84cb8a4 ("dm mpath: disable WRITE SAME if it fails")
implemented multipath specific disabling of WRITE SAME if it fails.
However, as that commit detailed, the multipath-only solution doesn't go
far enough if bio-based DM targets are stacked ontop of the
request-based dm-multipath target (as is commonly done using dm-linear
to support partitions on multipath devices, via kpartx).
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Tested-by: NAlex Chen <alex.chen@huawei.com>

lockdep complains about a circular locking.  And indeed, we need to
release the lock before calling dm_table_run_md_queue_async().

As such, commit 4cdd2ad7 ("dm mpath: fix lock order inconsistency in
multipath_ioctl") must also be reverted in addition to fixing the
lock order in the other dm_table_run_md_queue_async() callers.
Reported-by: NBart van Assche <bvanassche@acm.org>
Tested-by: NBart van Assche <bvanassche@acm.org>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Commit 3e9f1be1 ("dm mpath: remove process_queued_ios()") did not
consistently take the multipath device's spinlock (m->lock) before
calling dm_table_run_md_queue_async() -- which takes the q->queue_lock.

Found with code inspection using hint from reported lockdep warning.
Reported-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

The warning message "Unrecognised multipath message received" is
displayed in two different situations in multipath_message(): when the
number of arguments passed is invalid and when the string passed in
argv[0] is not recognized.

Make it easier to identify where the problem is by making these warnings
more specific with additional context for each case.
Signed-off-by: NJose Castillo <jcastillo@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

activate_path() is run without a lock, so the path might be
set to failed before activate_path() had a chance to run.
This patch add a check for ->active in activate_path() to
avoid unnecessary overhead by calling functions which are known
to be failing.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Return early for case when no path exists, and when the
pathgroup isn't ready. This eliminates the need for
extra nesting for the the common case.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>

multipath_map() is now just a wrapper around map_io(), so we
can rename map_io() to multipath_map().
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Reviewed-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>

When multipath needs to requeue I/O in the block layer the per-request
context shouldn't be allocated, as it will be freed immediately
afterwards anyway.  Avoiding this memory allocation will reduce memory
pressure during requeuing.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Reviewed-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>

process_queued_ios() has served 3 functions:
  1) select pg and pgpath if none is selected
  2) start pg_init if requested
  3) dispatch queued IOs when pg is ready

Basically, a call to queue_work(process_queued_ios) can be replaced by
dm_table_run_md_queue_async(), which runs request queue and ends up
calling map_io(), which does 1), 2) and 3).

Exception is when !pg_ready() (which means either pg_init is running or
requested), then multipath_busy() prevents map_io() being called from
request_fn.

If pg_init is running, it should be ok as long as pg_init_done() does
the right thing when pg_init is completed, I.e.: restart pg_init if
!pg_ready() or call dm_table_run_md_queue_async() to kick map_io().

If pg_init is requested, we have to make sure the request is detected
and pg_init will be started.  pg_init is requested in 3 places:
  a) __choose_pgpath() in map_io()
  b) __choose_pgpath() in multipath_ioctl()
  c) pg_init retry in pg_init_done()
a) is ok because map_io() calls __pg_init_all_paths(), which does 2).
b) needs a call to __pg_init_all_paths(), which does 2).
c) needs a call to __pg_init_all_paths(), which does 2).

So this patch removes process_queued_ios() and ensures that
__pg_init_all_paths() is called at the appropriate locations.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Reviewed-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>

There is no reason why multipath needs to queue requests internally for
queue_if_no_path or pg_init; we should rather push them back onto the
request queue.

And while we're at it we can simplify the conditional statement in
map_io() to make it easier to read.

Since mpath no longer does internal queuing of I/O the table info no
longer emits the internal queue_size.  Instead it displays 1 if queuing
is being used or 0 if it is not.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Reviewed-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>

This patch moves condition checks as a preparation of following
patches and has no effect on behaviour.
process_queued_ios() is the only caller of __pg_init_all_paths()
and 2 condition checks are moved from outside to inside without
side effects.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Reviewed-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>

An invalid ioctl will never be valid, irrespective of whether multipath
has active paths or not.  So for invalid ioctls we do not have to wait
for multipath to activate any paths, but can rather return an error
code immediately.  This fix resolves numerous instances of:

 udevd[]: worker [] unexpectedly returned with status 0x0100

that have been seen during testing.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

When pg_init is running no I/O can be submitted to the underlying
devices, as the path priority etc might change.  When using queue_io for
this, requests will be piling up within multipath as the block I/O
scheduler just sees a _very fast_ device.  All of this queued I/O has to
be resubmitted from within multipathing once pg_init is done.

This approach has the problem that it's virtually impossible to
abort I/O when pg_init is running, and we're adding heavy load
to the devices after pg_init since all of the queued I/O needs to be
resubmitted _before_ any requests can be pulled off of the request queue
and normal operation continues.

This patch will requeue the I/O that triggers the pg_init call, and
return 'busy' when pg_init is in progress.  With these changes the block
I/O scheduler will stop submitting I/O during pg_init, resulting in a
quicker path switch and less I/O pressure (and memory consumption) after
pg_init.
Signed-off-by: NHannes Reinecke <hare@suse.de>
[patch header edited for clarity and typos by Mike Snitzer]
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Whenever multipath_dtr() is happening we must prevent queueing any
further path activation work.  Implement this by adding a new
'pg_init_disabled' flag to the multipath structure that denotes future
path activation work should be skipped if it is set.  By disabling
pg_init and then re-enabling in flush_multipath_work() we also avoid the
potential for pg_init to be initiated while suspending an mpath device.

Without this patch a race condition exists that may result in a kernel
panic:

1) If after pg_init_done() decrements pg_init_in_progress to 0, a call
   to wait_for_pg_init_completion() assumes there are no more pending path
   management commands.
2) If pg_init_required is set by pg_init_done(), due to retryable
   mode_select errors, then process_queued_ios() will again queue the
   path activation work.
3) If free_multipath() completes before activate_path() work is called a
   NULL pointer dereference like the following can be seen when
   accessing members of the recently destructed multipath:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000090
RIP: 0010:[<ffffffffa003db1b>]  [<ffffffffa003db1b>] activate_path+0x1b/0x30 [dm_multipath]
[<ffffffff81090ac0>] worker_thread+0x170/0x2a0
[<ffffffff81096c80>] ? autoremove_wake_function+0x0/0x40

[switch to disabling pg_init in flush_multipath_work & header edits by Mike Snitzer]
Signed-off-by: NShiva Krishna Merla <shivakrishna.merla@netapp.com>
Reviewed-by: NKrishnasamy Somasundaram <somasundaram.krishnasamy@netapp.com>
Tested-by: NSpeagle Andy <Andy.Speagle@netapp.com>
Acked-by: NJunichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org

Allow user to change the number of IOs that are reserved by
request-based DM's mempools by writing to this file:
/sys/module/dm_mod/parameters/reserved_rq_based_ios

The default value is RESERVED_REQUEST_BASED_IOS (256).  The maximum
allowed value is RESERVED_MAX_IOS (1024).

Export dm_get_reserved_rq_based_ios() for use by DM targets and core
code.  Switch to sizing dm-mpath's mempool using DM core's configurable
'reserved_rq_based_ios'.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NFrank Mayhar <fmayhar@google.com>
Acked-by: NMikulas Patocka <mpatocka@redhat.com>

Workaround the SCSI layer's problematic WRITE SAME heuristics by
disabling WRITE SAME in the DM multipath device's queue_limits if an
underlying device disabled it.

The WRITE SAME heuristics, with both the original commit 5db44863
("[SCSI] sd: Implement support for WRITE SAME") and the updated commit
66c28f97 ("[SCSI] sd: Update WRITE SAME heuristics"), default to enabling
WRITE SAME(10) even without successfully determining it is supported.
After the first failed WRITE SAME the SCSI layer will disable WRITE SAME
for the device (by setting sdkp->device->no_write_same which results in
'max_write_same_sectors' in device's queue_limits to be set to 0).

When a device is stacked ontop of such a SCSI device any changes to that
SCSI device's queue_limits do not automatically propagate up the stack.
As such, a DM multipath device will not have its WRITE SAME support
disabled.  This causes the block layer to continue to issue WRITE SAME
requests to the mpath device which causes paths to fail and (if mpath IO
isn't configured to queue when no paths are available) it will result in
actual IO errors to the upper layers.

This fix doesn't help configurations that have additional devices
stacked ontop of the mpath device (e.g. LVM created linear DM devices
ontop).  A proper fix that restacks all the queue_limits from the bottom
of the device stack up will need to be explored if SCSI will continue to
use this model of optimistically allowing op codes and then disabling
them after they fail for the first time.

Before this patch:

EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: failing WRITE SAME IO with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.
device-mapper: multipath: Failing path 8:112.
end_request: I/O error, dev dm-6, sector 4616
dm-6: WRITE SAME failed. Manually zeroing.
end_request: I/O error, dev dm-6, sector 4616
end_request: I/O error, dev dm-6, sector 5640
end_request: I/O error, dev dm-6, sector 6664
end_request: I/O error, dev dm-6, sector 7688
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.
end_request: I/O error, dev dm-6, sector 524296
Aborting journal on device dm-6-8.
end_request: I/O error, dev dm-6, sector 524288
Buffer I/O error on device dm-6, logical block 65536
lost page write due to I/O error on dm-6
JBD2: Error -5 detected when updating journal superblock for dm-6-8.

# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
33553920

After this patch:

EXT4-fs (dm-6): mounted filesystem with ordered data mode. Opts: (null)
device-mapper: multipath: XXX snitm debugging: got -EREMOTEIO (-121)
device-mapper: multipath: XXX snitm debugging: WRITE SAME I/O failed with error=-121
end_request: critical target error, dev dm-6, sector 528
dm-6: WRITE SAME failed. Manually zeroing.

# cat /sys/block/sdh/queue/write_same_max_bytes
0
# cat /sys/block/dm-6/queue/write_same_max_bytes
0

It should be noted that WRITE SAME support wasn't enabled in DM
multipath until v3.10.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org # 3.10+

Since ENOSPC is a target-side error, dm-mpath should just pass the error
information to upper layer instead of retrying itself with path failover.
Otherwise it will end up failing all paths down while path checkers find
all paths ok.

ENOSPC can now be returned from SCSI device after commit a9d6ceb8
("[SCSI] return ENOSPC on thin provisioning failure").
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

When a medium error is detected the SCSI stack should return
ENODATA to the upper layers.

[jejb: fix whitespace error]
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When multipath needs to retry an ioctl the reference to the
current live table needs to be dropped. Otherwise a deadlock
occurs when all paths are down:
- dm_blk_ioctl takes a reference to the current table
  and spins in multipath_ioctl().
- A new table is being loaded, but upon resume the process
  hangs in dm_table_destroy() waiting for references to
  drop to zero.

With this patch the reference to the old table is dropped
prior to retry, thereby avoiding the deadlock.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Enable WRITE SAME support in dm multipath.  As far as multipath is
concerned it is just another write request.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Tested-by: NBharata B Rao <bharata.rao@gmail.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Use 'bio' in the name of variables and functions that deal with
bios rather than 'request' to avoid confusion with the normal
block layer use of 'request'.

No functional changes.
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Avoid returning a truncated table or status string instead of setting
the DM_BUFFER_FULL_FLAG when the last target of a table fills the
buffer.

When processing a table or status request, the function retrieve_status
calls ti->type->status. If ti->type->status returns non-zero,
retrieve_status assumes that the buffer overflowed and sets
DM_BUFFER_FULL_FLAG.

However, targets don't return non-zero values from their status method
on overflow. Most targets returns always zero.

If a buffer overflow happens in a target that is not the last in the
table, it gets noticed during the next iteration of the loop in
retrieve_status; but if a buffer overflow happens in the last target, it
goes unnoticed and erroneously truncated data is returned.

In the current code, the targets behave in the following way:
* dm-crypt returns -ENOMEM if there is not enough space to store the
  key, but it returns 0 on all other overflows.
* dm-thin returns errors from the status method if a disk error happened.
  This is incorrect because retrieve_status doesn't check the error
  code, it assumes that all non-zero values mean buffer overflow.
* all the other targets always return 0.

This patch changes the ti->type->status function to return void (because
most targets don't use the return code). Overflow is detected in
retrieve_status: if the status method fills up the remaining space
completely, it is assumed that buffer overflow happened.

Cc: stable@vger.kernel.org
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The mpio dereference should be moved below the BUG_ON NULL test
in multipath_end_io().

spatch with a semantic match was used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

When there are no paths and multipath receives an ioctl, it waits until
a path becomes available.  This behaviour is incorrect if the
"queue_if_no_path" setting was not specified, as then the ioctl should
be rejected immediately, which this patch now does.

commit 35991652 ("dm mpath: allow ioctls to trigger pg init") should
have checked if queue_if_no_path was configured before queueing IO.

Checking for the queue_if_no_path feature, like is done in map_io(),
allows the following table load to work without blocking in the
multipath_ioctl retry loop:

  echo "0 1024 multipath 0 0 0 0" | dmsetup create mpath_nodevs

Without this fix the multipath_ioctl will block with the following stack
trace:

  blkid           D 0000000000000002     0 23936      1 0x00000000
   ffff8802b89e5cd8 0000000000000082 ffff8802b89e5fd8 0000000000012440
   ffff8802b89e4010 0000000000012440 0000000000012440 0000000000012440
   ffff8802b89e5fd8 0000000000012440 ffff88030c2aab30 ffff880325794040
  Call Trace:
   [<ffffffff814ce099>] schedule+0x29/0x70
   [<ffffffff814cc312>] schedule_timeout+0x182/0x2e0
   [<ffffffff8104dee0>] ? lock_timer_base+0x70/0x70
   [<ffffffff814cc48e>] schedule_timeout_uninterruptible+0x1e/0x20
   [<ffffffff8104f840>] msleep+0x20/0x30
   [<ffffffffa0000839>] multipath_ioctl+0x109/0x170 [dm_multipath]
   [<ffffffffa06bfb9c>] dm_blk_ioctl+0xbc/0xd0 [dm_mod]
   [<ffffffff8122a408>] __blkdev_driver_ioctl+0x28/0x30
   [<ffffffff8122a79e>] blkdev_ioctl+0xce/0x730
   [<ffffffff811970ac>] block_ioctl+0x3c/0x40
   [<ffffffff8117321c>] do_vfs_ioctl+0x8c/0x340
   [<ffffffff81166293>] ? sys_newfstat+0x33/0x40
   [<ffffffff81173571>] sys_ioctl+0xa1/0xb0
   [<ffffffff814d70a9>] system_call_fastpath+0x16/0x1b
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.5+
Acked-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

flush[_delayed]_work_sync() are now spurious.  Mark them deprecated
and convert all users to flush[_delayed]_work().

If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.

This patch doesn't make any functional difference.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com> 

Commit outstanding metadata before returning the status for a dm thin
pool so that the numbers reported are as up-to-date as possible.

The commit is not performed if the device is suspended or if
the DM_NOFLUSH_FLAG is supplied by userspace and passed to the target
through a new 'status_flags' parameter in the target's dm_status_fn.

The userspace dmsetup tool will support the --noflush flag with the
'dmsetup status' and 'dmsetup wait' commands from version 1.02.76
onwards.
Tested-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

A SCSI device handler might get attached to a device during the
initial device scan.  We do not necessarily want to override
this when loading a multipath table, so this patch adds a new
multipath feature argument "retain_attached_hw_handler".

During SCSI device scan all loaded SCSI device handlers will be
consulted for a match (via scsi_dh's provided .match).  If a match is
found that device handler will be attached.  We need a way to have
userspace multipathd's provided 'hw_handler' not override the already
attached hardware handler.

When specifying the new feature 'retain_attached_hw_handler' multipath
will use the currently attached hardware handler instead of trying to
attach the one specified during table load.  If no hardware handler is
attached the specified hardware handler will still be used.

Leverages scsi_dh_attach's ability to increment the scsi_dh's reference
count if the same scsi_dh name is provided when attaching - currently
attached scsi_dh name is determined with scsi_dh_attached_handler_name.

Depends upon commit 7e8a74b1
("[SCSI] scsi_dh: add scsi_dh_attached_handler_name").
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Tested-by: NBabu Moger <babu.moger@netapp.com>
Reviewed-by: NChandra Seetharaman <sekharan@us.ibm.com>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device.  Until this has happened, ioctls return -EAGAIN.

With this patch, new paths are made available in response to an ioctl
too.  The processing of the ioctl gets delayed until this has happened.

Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.

Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure.  Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands).  For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too.  It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.

If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes.  Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes).  This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Acked-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

If the requested scsi_dh module is already loaded then skip
request_module().

Multipath table loads can hang in an unnecessary __request_module.
Reported-by: NBen Marzinski <bmarzins@redhat.com>
Cc: stable@kernel.org
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Device mapper uses sscanf to convert arguments to numbers. The problem is that
the way we use it ignores additional unmatched characters in the scanned string.

For example, this `if (sscanf(string, "%d", &number) == 1)' will match a number,
but also it will match number with some garbage appended, like "123abc".

As a result, device mapper accepts garbage after some numbers. For example
the command `dmsetup create vg1-new --table "0 16384 linear 254:1bla 34816bla"'
will pass without an error.

This patch fixes all sscanf uses in device mapper. It appends "%c" with
a pointer to a dummy character variable to every sscanf statement.

The construct `if (sscanf(string, "%d%c", &number, &dummy) == 1)' succeeds
only if string is a null-terminated number (optionally preceded by some
whitespace characters). If there is some character appended after the number,
sscanf matches "%c", writes the character to the dummy variable and returns 2.
We check the return value for 1 and consequently reject numbers with some
garbage appended.
Signed-off-by: NMikulas Patocka <mpatocka@redhat.com>
Acked-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

The map_context pointer should always be set. However, we have reports
that upon requeuing it is not set correctly.  So add set and clear
functions with a BUG_ON() to track the issue properly.
Signed-off-by: NJun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Acked-by: NHannes Reinecke <hare@suse.de>
Tested-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: NDave Wysochanski <dwysocha@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

A logical volume can map to just part of underlying physical volume.
In this case, it must be treated like a partition.

Based on a patch from Alasdair G Kergon.

Cc: Alasdair G Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Move multipath target argument parsing code into dm-table so other
targets can share it.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>

Avoid dereferencing a NULL pointer if the number of feature arguments
supplied is fewer than indicated.
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org

This allows us to move duplicated code in <asm/atomic.h>
(atomic_inc_not_zero() for now) to <linux/atomic.h>
Signed-off-by: NArun Sharma <asharma@fb.com>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David Miller <davem@davemloft.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>