The multicast hardware counter on 8168/8111 chips is only 32 bit while the
statistics in struct rtnl_link_stats64 are 64 bit.  Given that statistics
are requested on an irregular basis, an overflow of the hardware counter
can go unnoticed.  To count even very large numbers of multicast packets
reliably, add a software counter and remove previously applied code to
fill the multicast field requested by @rtl8169_get_stats64 with the values
read from the rx_multicast hardware counter.
Signed-off-by: NCorinna Vinschen <vinschen@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The r8169 driver collects statistical information returned by
@get_stats64 by counting them in the driver itself, even though many
(but not all) of the values are already collected by tally counters
(TCs) in the NIC.  Some of these TC values are not returned by
@get_stats64.  Especially the received multicast packages are missing
from /proc/net/dev.

Rectify this by fetching the TCs and returning them from
rtl8169_get_stats64.

The counters collected in the driver obviously disappear as soon as the
driver is unloaded so after a driver is loaded the counters always start
at 0. The TCs on the other hand are only reset by a power cycle.  Without
further considerations the values collected by the driver would not match
up against the TC values.

This patch introduces a new function rtl8169_reset_counters which
resets the TCs.  Also, since rtl8169_reset_counters shares most of
its code with rtl8169_update_counters, refactor the shared code into
two new functions  rtl8169_map_counters and rtl8169_unmap_counters.

Unfortunately chip versions prior to RTL_GIGA_MAC_VER_19 don't allow
to reset the TCs programatically.  Therefore introduce an addition to
the rtl8169_private struct and a function rtl8169_init_counter_offsets
to store the TCs at first rtl_open.  Use these values as offsets in
rtl8169_get_stats64.  Propagate a failure to reset *and* update the
counters up to rtl_open and emit a warning message, if so.
Signed-off-by: NCorinna Vinschen <vinschen@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Enforcing this flag in RxConfig for the mentioned chips fixes netdev
watchdog issues prepended with AMD IOMMU message(s) like:
AMD-Vi: Event logged [IO_PAGE_FAULT device=01:00.0 domain=0x001d address=0x0000000000003000 flags=0x0050]

Note that this flag is also set in Realtek's own driver for these chips.
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Tested-by: NAlexander Lindqvist <alexander@bitspace.se>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function r8169_csum_workaround is called in the ndo_start_xmit path of
the r8169 driver.  As such it should not be using dev_kfree_skb as it is
not irq safe, so instead we should be using dev_kfree_skb_any for freeing
in the dropped path, and dev_consume_skb_any for any frames that were
transmitted.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change 'firwmare' to 'firmware'
Signed-off-by: NYannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are certain regressions which are pointing to
these two commits which we are having a hard time
resolving.  So revert them for now.

Specifically this reverts:

	commit 0bec3b70
	Author: Florian Westphal <fw@strlen.de>
	Date:   Wed Jan 7 10:49:49 2015 +0100

	    r8169: add support for xmit_more

and

	commit 1e918876
	Author: Florian Westphal <fw@strlen.de>
	Date:   Wed Oct 1 13:38:03 2014 +0200

	    r8169: add support for Byte Queue Limits

There were some attempts by Eric Dumazet to address some obvious
problems in the TX flow, to see if they would fix the problems,
but none of them seem to help for the regression reporters.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace a magic number with a PCI #define symbol.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>

The same macros are used for rx as well. So rename it.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Delay update of hw tail descriptor if we know that another skb is going
to be sent.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add ephy parameter to rtl8168g.
Also change the common function of rtl8168g from "rtl_hw_start_8168g_1" to
 "rtl_hw_start_8168g". And function "rtl_hw_start_8168g_1" is used for
setting rtl8168g hardware parameters.

Following is the explanation of what hardware parameter change for.
rtl8168g may erroneous judge the PCIe signal quality and show the error bit
on PCI configuration space when in PCIe low power mode.
The following ephy parameters are for above issue.
{ 0x00, 0x0000,	0x0008 }
{ 0x0c, 0x37d0,	0x0820 }
{ 0x1e, 0x0000,	0x0001 }

rtl8168g may return to PCIe L0 from PCIe L0s low power mode too slow.
The following ephy parameter is for above issue.
{ 0x19, 0x8000,	0x0000 }
Signed-off-by: NChunhao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The r8169 use a pair of wmb() calls when setting up the descriptor rings.
The first is to synchronize the descriptor data with the descriptor status,
and the second is to synchronize the descriptor status with the use of the
MMIO doorbell to notify the device that descriptors are ready.  This can
come at a heavy price on some systems, and is not really necessary on
systems such as x86 as a simple barrier() would suffice to order store/store
accesses.  As such we can replace the first memory barrier with
dma_wmb() to reduce the cost for these accesses.

In addition the r8169 uses a rmb() to prevent compiler optimization in the
cleanup paths, however by moving the barrier down a few lines and replacing
it with a dma_rmb() we should be able to use it to guarantee
descriptor accesses do not occur until the device has updated the DescOwn
bit from its end.

One last change I made is to move the update of cur_tx in the xmit path to
after the wmb.  This way we can guarantee the device and all CPUs should
see the DescOwn update before they see the cur_tx value update.

Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This replaces most of the calls to netdev_alloc_skb_ip_align in the Realtek
drivers.  The one instance I didn't replace in 8139cp.c is because it was
called as a part of init and as such is not always accessed from the
softirq context.

Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace rtl_skb_pad with eth_skb_pad since they do the same thing.

Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cmac engine is the bridge between driver and dash firmware.
Other os may not disable cmac when leave. And r8169 did not allocate any
resources for cmac engine. Disable it to prevent abnormal system behavior.
Signed-off-by: NChunhao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RTL8168G/GU/H/EP and RTL8411B remove enable tx/rx from its own hw_start
function. This will prevent enable tx/rx before complete hardware tx/rx
setting.

Tx/Rx will be enabled in the end of function rtl_hw_start_8168.
Signed-off-by: NChunhao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8168EP is Realtek PCIe Gigabit Ethernet controller with DASH support.
It is a successor chip of RTL8168DP.

For RTL8168EP, the read/write ocp register is via eri channel type 2, so I
move ocp_xxx() related functions under rtl_eri_xxx. And use r8168dp_ocp_xxx()
for RTL8168DP ocp read/write, r8168ep_ocp_xxx() for RTL8168EP ocp read/write.

The way of checking dash enable is different with RTL8168DP. I use
r8168dp_check_dash()for RTL8168DP and r8168ep_check_dash() for RTL8168EP,
to check if dash is enabled.

The driver_start() and driver_stop() of RTL8168EP is also different with
RTL8168DP. I use rtl8168dp_driver_xxx() for RTL8168DP and
rtl8168ep_driver_xxx for RTL8168EP.

Right now, RTL8168EP phy mcu did not need firmware code patch, so I did not
add firmware code for it.
so I did not add firmware code for it.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

tested on RTL8168d/8111d model using 'super_netperf 40' with TCP/UDP_STREAM.

Output of
while true; do
    for n in inflight limit; do
          echo -n $n\ ; cat $n;
    done;
    sleep 1;
done

during netperf run, 100mbit peer:

inflight 0
limit 3028
inflight 6056
limit 4542

[ trimmed output for brevity, no limit/inflight changes during
  test steady-state ]

limit 4542
inflight 3028
limit 6122
inflight 0
limit 6122
[ changed cable to 1gbit peer, restart netperf ]
inflight 37850
limit 36336
inflight 33308
limit 31794
inflight 33308
limit 31794
inflight 27252
limit 25738
[ again, no changes during test ]
inflight 27252
limit 25738
inflight 0
limit 28766
[ change cable to 100mbit peer, restart netperf ]
limit 28766
inflight 27370
limit 28766
inflight 4542
limit 5990
inflight 6056
limit 4542
[ .. ]
inflight 6056
limit 4542
inflight 0

[end of test]

Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Acked-by: NEric Dumazet <edumazet@google.com>
Acked-by: NTom Herbert <therbert@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These two functions are used to inform dash firmware that driver is been
brought up or brought down. So call these two functions only when hardware dash
function is enabled.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In function "rtl8168_oob_notify", using function "rtl_eri_write" to access
eri register 0xe8, instead of using MAC register "ERIDR" and "ERIAR" to
access it.

For using function "rtl_eri_write" in function "rtl8168_oob_notify", need to
move down "rtl8168_oob_notify" related functions under the function
"rtl_eri_write".
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DASH function not only RTL8168DP can support, but also RTL8168EP.
So change the name of function "r8168dp_check_dash" to "r8168_check_dash".
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the name of function "rtl_w1w0_eri" to "rtl_w0w1_eri".

In this function, the local variable "val" is "write zeros then write ones".
Please see below code.

(val & ~m) | p

In this patch, change the function name from "xx_w1w0_xx" to "xx_w0w1_xx".
The changed function name is more suitable for it's behavior.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change function name from "rtl_w1w0_phy" to "rtl_w0w1_phy".
And its behavior from "write ones then write zeros" to
"write zeros then write ones".

In Realtek internal driver, bitwise operations are almost "write zeros then
write ones". For easy to port hardware parameters from Realtek internal driver
to Linux kernal driver "r8169", we would like to change this function's
behavior and its name.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RTL8168F RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8402 RTL8107E,
the magic packet enable bit is changed to eri 0xde bit0.

In this patch, change magic packet enable bit of these chips to eri 0xde bit0.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8168FB RTL8168G RTL8168GU RTL8411 RTL8411B RTL8106EUS RTL8402 can
support get mac address from backup mac address register.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8411B can support disable/enable pll function.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8168G also can disable/enable pll function.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an extra semi-colon so __rtl8169_set_features() is called every
time.

Fixes: 929a031d ('r8169: adjust __rtl8169_set_features')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: Hayes Wang <hayeswang@realtek.com>--
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the "changed" test in __rtl8169_set_features(). Instead, do
simple test in rtl8169_set_features().

Set the RxChkSum and RxVlan through __rtl8169_set_features() in
rtl_open().
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The setting should depend on the new features not the current one.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the parameter "features" of __rtl8169_set_features() is equal to
dev->features, the variable "changed" is alwayes 0, and nothing would
be changed.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Leftover from 6e1d0b89 ("r8169:add
support for RTL8168H and RTL8107E").
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RTL8168H is Realtek PCIe Gigabit Ethernet controller.
RTL8107E is Realtek PCIe Fast Ethernet controller.

This patch add support for these two chips.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines.  This issue was reported by checkpatch.

A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):

// <smpl>

@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@

- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;

// </smpl>

[bhelgaas: add semantic patch]
Signed-off-by: NBenoit Taine <benoit.taine@lip6.fr>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The ethernet port on my ASUS A88X Pro mainboard stopped working
several times a day, with messages like these in dmesg:

AMD-Vi: Event logged [IO_PAGE_FAULT device=05:00.0 domain=0x001e address=0x0000000000003000 flags=0x0050]

Searching the web for these messages led me to similar reports about
different hardware supported by r8169, and eventually to commits
3ced8c95 ('r8169: enforce RX_MULTI_EN
for the 8168f.') and eb2dc35d ('r8169:
RxConfig hack for the 8168evl'). So I tried this change, and it fixes
the problem for me.
Signed-off-by: NMichel Dänzer <michel@daenzer.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support the IPv6 hw checksum for RTL8111C and later chips. Note
that the hw has the limitation for the transport offset. The
checksum must be calculated by sw, when the transport offset is
out of the range which the hw accepts.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace large send with giant send for TSO for RTL8111C and later ICs.
The large send setting of the RTL8111DP is different from the other
chips. However, the giant send setting is the same for all the chips
which support it. Use the giant send to synchronize the settings.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the txd_version, split rtl8169_tso_csum() into
rtl8169_tso_csum_v1() and rtl8169_tso_csum_v2().
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For RTL8411, RTL8111G, RTL8402, RTL8105, and RTL8106, disable the feature
of entering the L2/L3 link state of the PCIe. When the nic starts the process
of entering the L2/L3 link state and the PCI reset occurs before the work
is finished, the work would be queued and continue after the next the PCI
reset occurs. This causes the device stays in L2/L3 link state, and the system
couldn't find the device.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Acked-by: NFrancois Romieu <romieu@fr.zoreil.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

net: get rid of SET_ETHTOOL_OPS

Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.

Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
-       SET_ETHTOOL_OPS(dev, ops);
+       dev->ethtool_ops = ops;

Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: NDave Miller <davem@davemloft.net>
Signed-off-by: NWilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>