- 05 6月, 2012 12 次提交
-
-
由 Alex Deucher 提交于
- Properly set up the RBs - Properly set up the SPI - Properly set up gb_addr_config This should fix rendering issues on certain cards. Signed-off-by: NAlex Deucher <alexander.deucher@amd.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Rafał Miłecki 提交于
Many TVs and A/V receivers don't work with this bit set. Problem was confirmed using: Onkyo TX-SR605, Sony BRAVIA KDL-52X3500, Sony BRAVIA KDL-40S40xx. In theory this bit shouldn't affect audio engine when feeding it with data, however it seems it does. Driver fglrx doesn't set that bit in any of the above cases. This fixes a regression introduced by 3.5-rc1. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Reviewed-by: NAlex Deucher <alexander.deucher@amd.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Rafał Miłecki 提交于
This is based on info released by AMD, should allow using audio in much more cases. Signed-off-by: NRafał Miłecki <zajec5@gmail.com> Reviewed-by: NAlex Deucher <alexander.deucher@amd.com> Cc: <stable@vger.kernel.org> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
由 Alex Deucher 提交于
Call it in the asic startup callback on all asics. Previously r600 and rv770 called it in the startup and resume callbacks while all the other asics called it in the startup callback. Signed-off-by: NAlex Deucher <alexander.deucher@amd.com> Reviewed-by: NRafał Miłecki <zajec5@gmail.com> Signed-off-by: NDave Airlie <airlied@redhat.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/{signal,vfs}由 Linus Torvalds 提交于
Pull signal and vfs compile breakage fixes from Al Viro. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: fixups for signal breakage * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: nommu: fix compilation of nommu.c
-
git://git.samba.org/sfrench/cifs-2.6由 Linus Torvalds 提交于
Pull cifs fixes from Steve French. * 'for-next' of git://git.samba.org/sfrench/cifs-2.6: CIFS: Move get_next_mid to ops struct CIFS: Make accessing is_valid_oplock/dump_detail ops struct field safe CIFS: Improve identation in cifs_unlock_range CIFS: Fix possible wrong memory allocation
-
由 Al Viro 提交于
Obvious brainos spotted by Geert. Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
-
由 Greg Ungerer 提交于
Compiling 3.5-rc1 for nommu targets gives: CC mm/nommu.o mm/nommu.c: In function ‘sys_mmap_pgoff’: mm/nommu.c:1489:2: error: ‘ret’ undeclared (first use in this function) mm/nommu.c:1489:2: note: each undeclared identifier is reported only once for each function it appears in It is trivially fixed by replacing 'ret' with the local variable that is already defined for the return value 'retval'. Signed-off-by: NGreg Ungerer <gerg@uclinux.org> Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
-
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm由 Linus Torvalds 提交于
Pull frontswap feature from Konrad Rzeszutek Wilk: "Frontswap provides a "transcendent memory" interface for swap pages. In some environments, dramatic performance savings may be obtained because swapped pages are saved in RAM (or a RAM-like device) instead of a swap disk. This tag provides the basic infrastructure along with some changes to the existing backends." Fix up trivial conflict in mm/Makefile due to removal of swap token code changing a line next to the new frontswap entry. This pull request came in before the merge window even opened, it got delayed to after the merge window by me just wanting to make sure it had actual users. Apparently IBM is using this on their embedded side, and Jan Beulich says that it's already made available for SLES and OpenSUSE users. Also acked by Rik van Riel, and Konrad points to other people liking it too. So in it goes. By Dan Magenheimer (4) and Konrad Rzeszutek Wilk (2) via Konrad Rzeszutek Wilk * tag 'stable/frontswap.v16-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/mm: frontswap: s/put_page/store/g s/get_page/load MAINTAINER: Add myself for the frontswap API mm: frontswap: config and doc files mm: frontswap: core frontswap functionality mm: frontswap: core swap subsystem hooks and headers mm: frontswap: add frontswap header file
-
由 Linus Torvalds 提交于
Merge branches 'irq-urgent-for-linus' and 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull irq and smpboot updates from Thomas Gleixner: "Just cleanup patches with no functional change and a fix for suspend issues." * 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: genirq: Introduce irq_do_set_affinity() to reduce duplicated code genirq: Add IRQS_PENDING for nested and simple irq * 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: smpboot, idle: Fix comment mismatch over idle_threads_init() smpboot, idle: Optimize calls to smp_processor_id() in idle_threads_init()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull timer updates from Thomas Gleixner: "The clocksource driver is pure hardware enablement and the skew option is default off, well tested and non dangerous." * 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: tick: Move skew_tick option into the HIGH_RES_TIMER section clocksource: em_sti: Add DT support clocksource: em_sti: Emma Mobile STI driver clockevents: Make clockevents_config() a global symbol tick: Add tick skew boot option
-
由 Linus Torvalds 提交于
Cyrill Gorcunov reports that I broke the fdinfo files with commit 30a08bf2 ("proc: move fd symlink i_mode calculations into tid_fd_revalidate()"), and he's quite right. The tid_fd_revalidate() function is not just used for the <tid>/fd symlinks, it's also used for the <tid>/fdinfo/<fd> files, and the permission model for those are different. So do the dynamic symlink permission handling just for symlinks, making the fdinfo files once more appear as the proper regular files they are. Of course, Al Viro argued (probably correctly) that we shouldn't do the symlink permission games at all, and make the symlinks always just be the normal 'lrwxrwxrwx'. That would have avoided this issue too, but since somebody noticed that the permissions had changed (which was the reason for that original commit 30a08bf2 in the first place), people do apparently use this feature. [ Basically, you can use the symlink permission data as a cheap "fdinfo" replacement, since you see whether the file is open for reading and/or writing by just looking at st_mode of the symlink. So the feature does make sense, even if the pain it has caused means we probably shouldn't have done it to begin with. ] Reported-and-tested-by: NCyrill Gorcunov <gorcunov@openvz.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 04 6月, 2012 5 次提交
-
-
由 Kukjin Kim 提交于
Should be 'exynos5_xxx' instead of 'exonys5_xxx'. It happened at the commit 30b84288 ("Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc") during v3.5 merge window. Signed-off-by: NKukjin Kim <kgene.kim@samsung.com> [ My bad - Linus ] Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm由 Linus Torvalds 提交于
Pull some left-over PM patches from Rafael J. Wysocki. * 'pm-acpi' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI / PM: Make acpi_pm_device_sleep_state() follow the specification ACPI / PM: Make __acpi_bus_get_power() cover D3cold correctly ACPI / PM: Fix error messages in drivers/acpi/bus.c rtc-cmos / PM: report wakeup event on ACPI RTC alarm ACPI / PM: Generate wakeup events on fixed power button
-
由 Linus Torvalds 提交于
This reverts commit 5ceb9ce6. That commit seems to be the cause of the mm compation list corruption issues that Dave Jones reported. The locking (or rather, absense there-of) is dubious, as is the use of the 'page' variable once it has been found to be outside the pageblock range. So revert it for now, we can re-visit this for 3.6. If we even need to: as Minchan Kim says, "The patch wasn't a bug fix and even test workload was very theoretical". Reported-and-tested-by: NDave Jones <davej@redhat.com> Acked-by: NHugh Dickins <hughd@google.com> Acked-by: NKOSAKI Motohiro <kosaki.motohiro@gmail.com> Acked-by: NMinchan Kim <minchan@kernel.org> Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com> Cc: Kyungmin Park <kyungmin.park@samsung.com> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Hugh Dickins 提交于
New tmpfs use of !PageUptodate pages for fallocate() is triggering the WARNING: at mm/page-writeback.c:1990 when __set_page_dirty_nobuffers() is called from migrate_page_copy() for compaction. It is anomalous that migration should use __set_page_dirty_nobuffers() on an address_space that does not participate in dirty and writeback accounting; and this has also been observed to insert surprising dirty tags into a tmpfs radix_tree, despite tmpfs not using tags at all. We should probably give migrate_page_copy() a better way to preserve the tag and migrate accounting info, when mapping_cap_account_dirty(). But that needs some more work: so in the interim, avoid the warning by using a simple SetPageDirty on PageSwapBacked pages. Reported-and-tested-by: NDave Jones <davej@redhat.com> Signed-off-by: NHugh Dickins <hughd@google.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Linus Torvalds 提交于
The comment above it says "Stat data, not accessed from path walking", but in fact some of inode fields we use for the common stat data was way down at the end of the inode, causing unnecessary cache misses for the common stat operations. The inode structure is pretty big, and this can change padding depending on field width, but at least on the common 64-bit configurations this doesn't change the size. Some of our inode layout has historically been to tro to avoid unnecessary padding fields, but cache locality is at least as important for layout, if not more. Noticed by looking at kernel profiles, and noticing that the "i_blkbits" access stood out like a sore thumb. Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 03 6月, 2012 13 次提交
-
-
由 Linus Torvalds 提交于
-
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm由 Linus Torvalds 提交于
Pull device-mapper updates from Alasdair G Kergon: "Improve multipath's retrying mechanism in some defined circumstances and provide a simple reserve/release mechanism for userspace tools to access thin provisioning metadata while the pool is in use." * tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: dm thin: provide userspace access to pool metadata dm thin: use slab mempools dm mpath: allow ioctls to trigger pg init dm mpath: delay retry of bypassed pg dm mpath: reduce size of struct multipath
-
由 Joe Thornber 提交于
This patch implements two new messages that can be sent to the thin pool target allowing it to take a snapshot of the _metadata_. This, read-only snapshot can be accessed by userland, concurrently with the live target. Only one metadata snapshot can be held at a time. The pool's status line will give the block location for the current msnap. Since version 0.1.5 of the userland thin provisioning tools, the thin_dump program displays the msnap as follows: thin_dump -m <msnap root> <metadata dev> Available here: https://github.com/jthornber/thin-provisioning-tools Now that userland can access the metadata we can do various things that have traditionally been kernel side tasks: i) Incremental backups. By using metadata snapshots we can work out what blocks have changed over time. Combined with data snapshots we can ensure the data doesn't change while we back it up. A short proof of concept script can be found here: https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb ii) Migration of thin devices from one pool to another. iii) Merging snapshots back into an external origin. iv) Asyncronous replication. Signed-off-by: NJoe Thornber <ejt@redhat.com> Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
-
由 Mike Snitzer 提交于
Use dedicated caches prefixed with a "dm_" name rather than relying on kmalloc mempools backed by generic slab caches so the memory usage of thin provisioning (and any leaks) can be accounted for independently. Signed-off-by: NMike Snitzer <snitzer@redhat.com> Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
-
由 Mikulas Patocka 提交于
After the failure of a group of paths, any alternative paths that need initialising do not become available until further I/O is sent to the device. Until this has happened, ioctls return -EAGAIN. With this patch, new paths are made available in response to an ioctl too. The processing of the ioctl gets delayed until this has happened. Instead of returning an error, we submit a work item to kmultipathd (that will potentially activate the new path) and retry in ten milliseconds. Note that the patch doesn't retry an ioctl if the ioctl itself fails due to a path failure. Such retries should be handled intelligently by the code that generated the ioctl in the first place, noting that some SCSI commands should not be retried because they are not idempotent (XOR write commands). For commands that could be retried, there is a danger that if the device rejected the SCSI command, the path could be errorneously marked as failed, and the request would be retried on another path which might fail too. It can be determined if the failure happens on the device or on the SCSI controller, but there is no guarantee that all SCSI drivers set these flags correctly. Signed-off-by: NMikulas Patocka <mpatocka@redhat.com> Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
-
由 Mike Christie 提交于
If I/O needs retrying and only bypassed priority groups are available, set the pg_init_delay_retry flag to wait before retrying. If, for example, the reason for the bypass is that the controller is getting reset or there is a firmware upgrade happening, retrying right away would cause a flood of log messages and retries for what could be a few seconds or even several minutes. Signed-off-by: NMike Christie <michaelc@cs.wisc.edu> Acked-by: NMike Snitzer <snitzer@redhat.com> Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
-
由 Mike Snitzer 提交于
Move multipath structure's 'lock' and 'queue_size' members to eliminate two 4-byte holes. Also use a bit within a single unsigned int for each existing flag (saves 8-bytes). This allows future flags to be added without each consuming an unsigned int. Signed-off-by: NMike Snitzer <snitzer@redhat.com> Acked-by: NHannes Reinecke <hare@suse.de> Signed-off-by: NAlasdair G Kergon <agk@redhat.com>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net由 Linus Torvalds 提交于
Pull networking updates from David Miller: 1) Make syn floods consume significantly less resources by a) Not pre-COW'ing routing metrics for SYN/ACKs b) Mirroring the device queue mapping of the SYN for the SYN/ACK reply. Both from Eric Dumazet. 2) Fix calculation errors in Byte Queue Limiting, from Hiroaki SHIMODA. 3) Validate the length requested when building a paged SKB for a socket, so we don't overrun the page vector accidently. From Jason Wang. 4) When netlabel is disabled, we abort all IP option processing when we see a CIPSO option. This isn't the right thing to do, we should simply skip over it and continue processing the remaining options (if any). Fix from Paul Moore. 5) SRIOV fixes for the mellanox driver from Jack orgenstein and Marcel Apfelbaum. 6) 8139cp enables the receiver before the ring address is properly programmed, which potentially lets the device crap over random memory. Fix from Jason Wang. 7) e1000/e1000e fixes for i217 RST handling, and an improper buffer address reference in jumbo RX frame processing from Bruce Allan and Sebastian Andrzej Siewior, respectively. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: fec_mpc52xx: fix timestamp filtering mcs7830: Implement link state detection e1000e: fix Rapid Start Technology support for i217 e1000: look into the page instead of skb->data for e1000_tbi_adjust_stats() r8169: call netif_napi_del at errpaths and at driver unload tcp: reflect SYN queue_mapping into SYNACK packets tcp: do not create inetpeer on SYNACK message 8139cp/8139too: terminate the eeprom access with the right opmode 8139cp: set ring address before enabling receiver cipso: handle CIPSO options correctly when NetLabel is disabled net: sock: validate data_len before allocating skb in sock_alloc_send_pskb() bql: Avoid possible inconsistent calculation. bql: Avoid unneeded limit decrement. bql: Fix POSDIFF() to integer overflow aware. net/mlx4_core: Fix obscure mlx4_cmd_box parameter in QUERY_DEV_CAP net/mlx4_core: Check port out-of-range before using in mlx4_slave_cap net/mlx4_core: Fixes for VF / Guest startup flow net/mlx4_en: Fix improper use of "port" parameter in mlx4_en_event net/mlx4_core: Fix number of EQs used in ICM initialisation net/mlx4_core: Fix the slave_id out-of-range test in mlx4_eq_int
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip由 Linus Torvalds 提交于
Pull straggler x86 fixes from Peter Anvin: "Three groups of patches: - EFI boot stub documentation and the ability to print error messages; - Removal for PTRACE_ARCH_PRCTL for x32 (obsolete interface which should never have been ported, and the port is broken and potentially dangerous.) - ftrace stack corruption fixes. I'm not super-happy about the technical implementation, but it is probably the least invasive in the short term. In the future I would like a single method for nesting the debug stack, however." * 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86, x32, ptrace: Remove PTRACE_ARCH_PRCTL for x32 x86, efi: Add EFI boot stub documentation x86, efi; Add EFI boot stub console support x86, efi: Only close open files in error path ftrace/x86: Do not change stacks in DEBUG when calling lockdep x86: Allow nesting of the debug stack IDT setting x86: Reset the debug_stack update counter ftrace: Use breakpoint method to update ftrace caller ftrace: Synchronize variable setting with breakpoints
-
由 Linus Torvalds 提交于
This reverts the tty layer change to use per-tty locking, because it's not correct yet, and fixing it will require some more deep surgery. The main revert is d29f3ef3 ("tty_lock: Localise the lock"), but there are several smaller commits that built upon it, they also get reverted here. The list of reverted commits is: fde86d31 - tty: add lockdep annotations 8f6576ad - tty: fix ldisc lock inversion trace d3ca8b64 - pty: Fix lock inversion b1d679af - tty: drop the pty lock during hangup abcefe5f - tty/amiserial: Add missing argument for tty_unlock() fd11b42e - cris: fix missing tty arg in wait_event_interruptible_tty call d29f3ef3 - tty_lock: Localise the lock The revert had a trivial conflict in the 68360serial.c staging driver that got removed in the meantime. Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Stephan Gatzka 提交于
skb_defer_rx_timestamp was called with a freshly allocated skb but must be called with rskb instead. Signed-off-by: NStephan Gatzka <stephan@gatzka.org> Cc: stable <stable@vger.kernel.org> Acked-by: NRichard Cochran <richardcochran@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ondrej Zary 提交于
Add .status callback that detects link state changes. Tested with MCS7832CV-AA chip (9710:7830, identified as rev.C by the driver). Fixes https://bugzilla.kernel.org/show_bug.cgi?id=28532Signed-off-by: NOndrej Zary <linux@rainbow-software.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/viro/{vfs,signal}由 Linus Torvalds 提交于
Pull vfs fix and a fix from the signal changes for frv from Al Viro. The __kernel_nlink_t for powerpc got scrogged because 64-bit powerpc actually depended on the default "unsigned long", while 32-bit powerpc had an explicit override to "unsigned short". Al didn't notice, and made both of them be the unsigned short. The frv signal fix is fallout from simplifying the do_notify_resume() code, and leaving an extra parenthesis. * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: powerpc: Fix size of st_nlink on 64bit * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: frv: Remove bogus closing parenthesis
-
- 02 6月, 2012 10 次提交
-
-
由 Anton Blanchard 提交于
commit e57f93cc (powerpc: get rid of nlink_t uses, switch to explicitly-sized type) changed the size of st_nlink on ppc64 from a long to a short, resulting in boot failures. Signed-off-by: NAnton Blanchard <anton@samba.org> Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
-
由 Geert Uytterhoeven 提交于
Introduced by commit 6fd84c08 ("TIF_RESTORE_SIGMASK can be set only when TIF_SIGPENDING is set") Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
-
由 Bruce Allan 提交于
The definition of I217_PROXY_CTRL must use the BM_PHY_REG() macro instead of the PHY_REG() macro for PHY page 800 register 70 since it is for a PHY register greater than the maximum allowed by the latter macro, and fix a typo setting the I217_MEMPWR register in e1000_suspend_workarounds_ich8lan. Also for clarity, rename a few defines as bit definitions instead of masks. Signed-off-by: NBruce Allan <bruce.w.allan@intel.com> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
This is another fixup where the data is not transfered into buffer addressed by skb->data but into a page. Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Tested-by: NAaron Brown <aaron.f.brown@intel.com> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
由 Linus Torvalds 提交于
Merge fixups for the mac NLS tables from Andrew. * emailed from Andrew Morton, and one cleanup by me: nls: fix (and rename) mac NLS table files and config options fs/nls/Makefile: remove bogus CONFIG_ assignments
-
由 Linus Torvalds 提交于
The config options in the Kconfig file (with _CODEPAGE_ in the name) didn't match the config option name in the Makefile (no _CODEPAGE_). And both of them were of the hard-to-read MACXYZZY variety, which made them hard to parse for normal humans: MACROMAN easily reads as "macro man", not as "Mac Roman". So rename the options to be consistent, and be NLS_MAC_xyzzy. Rename the files to be mac-xyzzy.c too, and drop the "nls" part entirely (it's already in the directory name). Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Andrew Morton 提交于
These were debug things which snuck through. Reported-by: NYinghai Lu <yinghai@kernel.org> Cc: Vladimir Serbinenko <phcoder@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://github.com/schandinat/linux-2.6由 Linus Torvalds 提交于
Pull fbdev updates from Florian Tobias Schandinat: - driver for AUO-K1900 and AUO-K1901 epaper controller - large updates for OMAP (e.g. decouple HDMI audio and video) - some updates for Exynos and SH Mobile - various other small fixes and cleanups * tag 'fbdev-updates-for-3.5' of git://github.com/schandinat/linux-2.6: (130 commits) video: bfin_adv7393fb: Fix cleanup code video: exynos_dp: reduce delay time when configuring video setting video: exynos_dp: move sw reset prioir to enabling sw defined function video: exynos_dp: use devm_ functions fb: handle NULL pointers in framebuffer release OMAPDSS: HDMI: OMAP4: Update IRQ flags for the HPD IRQ request OMAPDSS: Apply VENC timings even if panel is disabled OMAPDSS: VENC/DISPC: Delay dividing Y resolution for managers connected to VENC OMAPDSS: DISPC: Support rotation through TILER OMAPDSS: VRFB: remove compiler warnings when CONFIG_BUG=n OMAPFB: remove compiler warnings when CONFIG_BUG=n OMAPDSS: remove compiler warnings when CONFIG_BUG=n OMAPDSS: DISPC: fix usage of dispc_ovl_set_accu_uv OMAPDSS: use DSI_FIFO_BUG workaround only for manual update displays OMAPDSS: DSI: Support command mode interleaving during video mode blanking periods OMAPDSS: DISPC: Update Accumulator configuration for chroma plane drivers/video: fsl-diu-fb: don't initialize the THRESHOLDS registers video: exynos mipi dsi: support reverse panel type video: exynos mipi dsi: Properly interpret the interrupt source flags video: exynos mipi dsi: Avoid races in probe() ...
-
git://git.infradead.org/linux-mtd由 Linus Torvalds 提交于
Pull mtd update from David Woodhouse: - More robust parsing especially of xattr data in JFFS2 - Updates to mxc_nand and gpmi drivers to support new boards and device tree - Improve consistency of information about ECC strength in NAND devices - Clean up partition handling of plat_nand - Support NAND drivers without dedicated access to OOB area - BCH hardware ECC support for OMAP - Other fixes and cleanups, and a few new device IDs Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to added include files next to each other. * tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits) mtd: mxc_nand: move ecc strengh setup before nand_scan_tail mtd: block2mtd: fix recursive call of mtd_writev mtd: gpmi-nand: define ecc.strength mtd: of_parts: fix breakage in Kconfig mtd: nand: fix scan_read_raw_oob mtd: docg3 fix in-middle of blocks reads mtd: cfi_cmdset_0002: Slight cleanup of fixup messages mtd: add fixup for S29NS512P NOR flash. jffs2: allow to complete xattr integrity check on first GC scan jffs2: allow to discriminate between recoverable and non-recoverable errors mtd: nand: omap: add support for hardware BCH ecc ARM: OMAP3: gpmc: add BCH ecc api and modes mtd: nand: check the return code of 'read_oob/read_oob_raw' mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw' mtd: m25p80: Add support for Winbond W25Q80BW jffs2: get rid of jffs2_sync_super jffs2: remove unnecessary GC pass on sync jffs2: remove unnecessary GC pass on umount jffs2: remove lock_super mtd: gpmi: add gpmi support for mx6q ...
-
git://cavan.codon.org.uk/platform-drivers-x86由 Linus Torvalds 提交于
Pull x86 platform driver updates from Matthew Garrett: "Some significant improvements for the Sony driver on newer machines, but other than that mostly just minor fixes and a patch to remove the broken rfkill code from the Dell driver." * 'for_linus' of git://cavan.codon.org.uk/platform-drivers-x86: (35 commits) apple-gmux: Fix up the suspend/resume patch dell-laptop: Remove rfkill code toshiba_acpi: Fix mis-merge dell-laptop: Add touchpad led support for Dell V3450 acer-wmi: add 3 laptops to video backlight vendor mode quirk table sony-laptop: add touchpad enable/disable function sony-laptop: add missing Fn key combos for 0x100 handlers sony-laptop: add support for more WWAN modems sony-laptop: new keyboard backlight handle sony-laptop: add high speed battery charging function sony-laptop: support automatic resume on lid open sony-laptop: adjust error handling in finding SNC handles sony-laptop: add thermal profiles support sony-laptop: support battery care functions sony-laptop: additional debug statements sony-laptop: improve SNC initialization and acpi notify callback code sony-laptop: use kstrtoul to parse sysfs values sony-laptop: generalise ACPI calls into SNC functions sony-laptop: fix return path when no ACPI buffer is allocated sony-laptop: use soft rfkill status stored in hw ...
-