While being there, change C++ style comments to /* */.
Signed-off-by: NRobert Schwebel <r.schwebel@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NFelipe Balbi <balbi@ti.com>

A recent commit obsoleted the is_vbus_present function, so
we must not use it any more.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The Synopsys USB device controller requires all OUT transfer request
lengths to be aligned to max packet size. The mass storage gadgets do
not meet this requirement for Super Speed. The gadgets already have a
function which performs this alignment for CBW packets, so use it for
data packets too.

The alternative would be to implement bounce buffers in the DWC3
driver, but that could have a significant impact on performance.

This version is based upon a more-correct patch written by Alan
Stern.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The code in the MIDI gadget was already sort of prepared for multi-port
configuration, so the streaming logic itself didn't need much tweaking.
However, the descriptors change when the number of ports do, and so some
rework of the the preparation algorithms were necessary.

Successfully tested on Linux and Max OS X hosts for both input and
output streams.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Make use of the newly added MIDI function in f_midi.c and strip down
the MIDI gadget code radically. Also use the generic framework function
to avoid code duplication and rename some symbols to bring them in sync
with other code in the gadget framework.

[ balbi@ti.com : fix Section mismatch warnings.
	rebased on top of usb_speed_string() patch to
	avoid conflicts. ]
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds f_midi.c to implement a USB gadget function that works
with the composite framework, so it can be combined with other USB
functions.

The code for the ALSA/MIDI logic was taken from the midi device gadget,
other parts have been rewritten to benefit from the dynamic descriptor
allocation features.

This was successfully tested on an OMAP3 board.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Move function to fix langwell_udc.c build error:

drivers/usb/gadget/langwell_udc.c: In function 'show_langwell_udc':
drivers/usb/gadget/langwell_udc.c:1693:3: error: implicit declaration of function 'lpm_device_speed'
drivers/usb/gadget/langwell_udc.c: At top level:
drivers/usb/gadget/langwell_udc.c:2637:37: error: conflicting types for 'lpm_device_speed'
drivers/usb/gadget/langwell_udc.c:1693:20: note: previous implicit declaration of 'lpm_device_speed' was here
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Acked-by: NFelipe Balbi <balbi@ti.com>
Cc:	linux-usb@vger.kernel.org

SH7757 has a USB function with internal DMA controller (SUDMAC).
This patch supports the SUDMAC. The SUDMAC is incompatible with
general-purpose DMAC. So, it doesn't use dmaengine.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch also fix the balance of braces.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

R8A66597 has the pin of WR0 and WR1. So, if one write-pin of CPU
connects to the pins, we have to change the setting of FIFOSEL
register in the controller. If we don't change the setting,
the controller cannot send the data of odd length.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The Kirkwood gave an unaligned memory access error on
line 742 of drivers/usb/host/echi-hcd.c:
"ehci->last_periodic_enable = ktime_get_real();"
Signed-off-by: NHarro Haan <hrhaan@gmail.com>
Cc: stable <stable@kernel.org>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add PID 0xfc8a, 0xfc8b for device Sony Ericsson Urban
Signed-off-by: NHakan Kvist <hakan.kvist@sonyericsson.com>
Signed-off-by: NOskar Andero <oskar.andero@sonyericsson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These files uses the full set of MODULE_ macros and so need to
include module.h directly.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

our parameter structures need to be written to
HW, so instead of assuming little endian, we
convert those into bit shifts.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The dwc3 core has internal clock gating support.

Let's allow that to happen by clearing the disable
bit in GCTL register.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

cache the contents of GHWPARAMS* registers in
our device structure for easy access.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

That structure will hold a copy of readonly
GHWPARAMS* registers for ease accessing by
the driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The following patch adds support for streams
to dwc3 driver.

While at that, also fix one small issue on
endpoint disable where we should clear all
flags not only ENABLED.
Reviewied-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We already have the value from gadget drivers,
just need to pass it to our controller.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix offset calculation in dwc3_trb_dma_offset()
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This makes DWC3_EP_WEDGE do the right thing, which is
prevent DWC3_EP_WEDGE from ever being cleared by a
ClearFeature(HALT) command.

[ balbi@ti.com : allowed set_wedge to send SetHalt command
	to controller ]
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

An older version of the databook said to wait for the FIFO to
drain, but that has been removed from the newer databooks.

Waiting for RxFIFO to drain caused problems when testing against
one of the host controllers available in the market.

After talking to one of the RTL engineers, he stated that we
should _not_ wait for RxFIFO to drain.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

DEPSTARTCFG for non-EP0 EPs must only be sent once per config

[ balbi@ti.com : changed config_start to start_config_issued ]
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some people think that this line is not compatible with the GPL. The
statement was required due to the Buenos Aires Convention and is now
deprecated. I remove it because it is said that it is pointless nowdays.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use "ep0in" and "ep0out" instead "ep1in" and "ep0out" which is confusing
and not consistent with the remaining output.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We already give requests back in dwc3_ep0_stall_and_restart() so
doing it again here will most likely corrupt the list.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The way it was before was really meaningless.
Now it looks saner.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We don't need to care about direction on a two stage
transfer.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

According to USB 3.0 Specification, a SetAddress()
while device is in Configured State has an unspecified
behavior (see Section 9.4.6). Still USB30CV wasn't
happy with my Stall reply.

To make that thing happy, just accept the SetAddress()
always. No problems have been observed thus far.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

My webcam is a Logitech C300 and I get "chipmunk"ed squeaky sound.
The following trivial patch fixes it.
Signed-off-by: NJon Levell <linuxusb@coralbark.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add to the dev_state and alloc_async structures the user namespace
corresponding to the uid and euid.  Pass these to kill_pid_info_as_uid(),
which can then implement a proper, user-namespace-aware uid check.

Changelog:
Sep 20: Per Oleg's suggestion: Instead of caching and passing user namespace,
	uid, and euid each separately, pass a struct cred.
Sep 26: Address Alan Stern's comments: don't define a struct cred at
	usbdev_open(), and take and put a cred at async_completed() to
	ensure it lasts for the duration of kill_pid_info_as_cred().
Signed-off-by: NSerge Hallyn <serge.hallyn@canonical.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

"length" is type size_t so the cast to unsigned int truncates the
upper bytes.  This isn't an issue in real life (I've checked the
callers) but it's a bit messy.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

add device ID for "HP un2430 Mobile Broadband Module"
Signed-off-by: NRigbert Hamisch <rigbert@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In the usb printer class specific request get_device_id the value of
wIndex is (interface << 8 | altsetting) instead of just interface.
This enables the detection of some printers with libusb.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NMatthias Dellweg <2500@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Alan Stern points out that after spin_unlock(&ps->lock) there is no
guarantee that ps->pid won't be freed.  Since kill_pid_info_as_uid() is
called after the spin_unlock(), the pid passed to it must be pinned.
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NSerge Hallyn <serge.hallyn@canonical.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1488) improves the comments and logic in uhci-hcd's
suspend routine.  The existing comments are hard to understand and
don't give a good idea of what's really going on.

The question of whether EGSM (Enter Global Suspend Mode) and RD
(enable Resume Detect interrupts) can be useful when they're not both
set is difficult.  The spec doesn't give any details on how they
interact with system wakeup, although clearly they are meant to be
used together.  To be safe, the patch changes the subroutine so that
neither bit gets set unless they both do.  There shouldn't be any
functional changes from this; only systems that are designed badly or
broken in some way need to avoid using those bits.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1486) implements the kernel's new wakeup policy for USB
host controllers.  Since they don't generate wakeup requests on their
but merely forward requests from their root hubs toward the CPU, they
should be enabled for wakeup by default.

Also, to be compliant with both the old and new policies, root hubs
should not be enabled for remote wakeup by default.  Userspace must
enable it explicitly if it is desired.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This removes the need of ifdefs within the init function and with it the
headache about the correct clean without bus X but with bus/platform Y &
Z.
xhci-pci is only compiled if CONFIG_PCI is selected which can be
de-selected now without trouble. For now the result is kinda useless
because we have no other glue code. However, since nobody is using
USB_ARCH_HAS_XHCI then it should not be an issue :)
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

xhci_gen_setup() is generic so it can be used to perform the bare xhci
setup even on non-pci based platform. The typedef for the function
pointer is moved into the headerfile
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>