This was an old workaround for solving latency issues with
certain Miracast adapters like ActionTec. However this isn't
needed anymore and furthermore it hurts throughput in other
use cases.
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When the netdetect debugfs entry was removed, the nd_config element
was accidentally left in the iwl_mvm structure.  Remove it.

Fixes: dbb04b0d ("iwlwifi: mvm: remove netdetect debugfs entry")
Reported-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The d0i3 flag in the device configuration structure is redundant,
because the same information can be determined by checking the
firmware capability flag.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware debug trigger ID is always a compile-time constant,
so we can use a build-time assertion to validate that it is in
fact a valid constant.

To make that really guaranteed to work, convert this and the
inline function iwl_fw_dbg_trigger_simple_stop() to macros.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When there's a bt-wifi contention that requires arbitration,
we use a priority-based mechanism to decide which comm wins.
Over time, use cases become more and more complex, with multiple
concurrent active links with different traffic types and different QoS
requirements, on both WiFi and BT sides.
This, in turn, requires us to elaborate our prioritization mechanism.
However, our legacy products included hw that does not supports this,
so selectively enable this on specific hw - as signaled by the firmware.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Configure the FW to use fragmented scan when the traffic load is high
or low latency traffic is on. This is useful for scans that are
managed by the FW (e.g. scheduled scan).
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Part of reorganising wireless drivers directory and Kconfig.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Instead of only allowing the caller to decide whether the CMD_ASYNC
flag is set, let it pass the entire flags bitmask.  This allows more
flexibility and will be needed when we call this function in the
suspend flow (where other flags are needed).
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Since the new multi-queue capability depends on a new firmware API,
we can already add some code for it. If the new API is present, a
new opmode ops struct is used that handles the new rx_rss method.

For now, only restructure the RX handling to distinguish between
the two. Future patches will convert the new infrastructure to
actually use the new RX descriptor layout.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The only NVM section not captured in debugfs.
Signed-off-by: NMoshe Harel <moshe.harel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When enabling a queue, the default SSN is 0.

Allow determining what that SSN should be, if required. This
can happen, for example, if a queue gets reconfigured.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

"DQA" is shorthand for "dynamic queue allocation", with the
idea of allocating queues per-RA/TID on-demand rather than
using shared queues statically allocated per vif. The goal
of this is to enable future features (like GO PM) and to
improve performance measurements of TX traffic.

When RA/TID streams can't be neatly sorted into different AC
queues, DQA allows sharing queues for the same RA. This means
that DQA allows different ACs may reach the same HW queue.

Update the code to allow such queue sharing by having a mapping
between the HW queue and the mac80211 queues using it (as this
could be more than one queue).
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

During the CT-kill exit flow, the card is powered up and partially
initialized to check if the temperature is already low enough.
Unfortunately the init bails early because the CT-kill flag is set.
Make the code bail early only for HW RF-kill, as was intended by the
author. CT-kill is self-imposed and is not really RF-kill.

Fixes: 31b8b343 ("iwlwifi: fix RFkill while calibrating")
Cc: <stable@vger.kernel.org> [3.18+]
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Commit "iwlwifi: mvm: don't ask beacons when AP vif and no
assoc sta" directly called iwl_mvm_mac_ctxt_cmd_ap() to update the
MAC context when adding/removing a station. However, this ignores
the case that the vif is actually a P2P GO.

Fix this by calling iwl_mvm_mac_ctxt_changed() that handles P2P GO
case as well.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Its a bit odd that debugfs_create_bool() takes 'u32 *' as an argument,
when all it needs is a boolean pointer.

It would be better to update this API to make it accept 'bool *'
instead, as that will make it more consistent and often more convenient.
Over that bool takes just a byte.

That required updates to all user sites as well, in the same commit
updating the API. regmap core was also using
debugfs_{read|write}_file_bool(), directly and variable types were
updated for that to be bool as well.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NMark Brown <broonie@kernel.org>
Acked-by: NCharles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We don't support firmwares that don't use the new API.
This also allows to use all the SCD queues, so increase
the reported number of queues to 31.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

When in AP mode, we need beacons from other APs for HT protection.
However, when there's no any associated station we will not do
any Tx and thus don't really need beacons. On the other hand, these
beacons will cause a lot of unnecessary wakeups which increase our
power consumption. Handle this by asking FW to pass beacons only when
there's at least one associated station.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

When receiving statistics notification there is a field of average energy.
This is defines as signed 8 bit, while FW refers to it as unsigned.
when the energy is higher than 127 this causes in iwl_mvm_stat_iterator
a wrong computation of the signal
     int sig = -stats->general.beacon_filter_average_energy;
resulting in incorrect CQM event (change from low to high).

While at it - update the rest of the fields to the correct type.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>

The mac80211 patch to pass the NAPI struct only changed iwlwifi to
store the NAPI struct, but we can do better: pass it directly from
the lower transport layer to the opmode during RX, and then on to
mac80211 from there.

When we add multiple RX queues, we can then pass the appropriate
NAPI struct properly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Change the FW debug trigger tlv to include a monitor only
option. Setting this option to true will cause fw dump triggers
to only collect monitor data and skip other dumps such as
SMEM, SRAM, CSR, PRPH, etc.
This option is used when accessing the different parts of the
firmware memory is not wanted and can cause unwanted behavior
like when debugging TX latency.
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Family 8000 products has 2 embedded processors, the first
known as LMAC (lower MAC) and implements the functionality from
previous products, the second one is known as UMAC (upper MAC)
and is used mainly for driver offloads as well as new features.
The UMAC is typically “less” real-time than the LMAC and is used
for higher level controls.
The UMAC's code/data size is estimated to be in the mega-byte arena,
taking into account the code it needs to replace in the driver and
the set of new features.

In order to allow the UMAC to execute code that is bigger than its code
memory, we allow the UMAC embedded processor to page out code pages on
DRAM.

When the device is master on the bus(PCI) the driver saves the UMAC's
image pages in blocks of 32K in the DRAM and sends the layout of the
pages to the FW. The FW can load / unload the pages on its own.

The driver can support up to 1 MB of pages.

Add paging mechanism for the UMAC on PCI in order to allow the program
to use a larger virtual space while using less physical memory on the
device.
Signed-off-by: NEran Harary <eran.harary@intel.com>
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Move the TX PN assignment (for CCMP only) to the driver. This prepares
the driver for future DSO (driver segmentation offload) where it will
split an SKB into multiple MPDUs by itself.

For TDLS, split out the CCMP TX command handling so that it won't get
a PN assigned, the firmware assigns the PN in that case.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

TCP software implementation on the host requires extensive computing
power.  Offloading even some of the TCP/IP stack to the NIC might save
a significant overhead. In order to enable this feature on our hw,
we need to configure it first. Once done, we mark this capability,
to be advertised later to the OS via ieee80211_register_hw.
The driver Rx indications for TCP Checksum is integrated within the
standard Rx status. The driver responds to those indications as follows:
If the frame was tested by hw and checksum ok report CHECKSUM_UNNECESSARY.
Otherwise, report CHECKSUM_NONE.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

As the firmware is slowly running out of command IDs and grouping of
commands is desirable anyway, the firmware is extending the command
header from 4 bytes to 8 bytes to introduce a group (in place of the
former flags field, since that's always 0 on commands and thus can
be easily used to distinguish between the two.

In order to support this most easily in the driver widen the command
command ID used in the command sending functions and encode the new
values (group and version) in the ID. That way existing code doesn't
have to be changed (since the higher bits are 0 automatically) and
newer code can easily use the new ID generation function to create a
value to use in place of just the command ID.
Signed-off-by: NAviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

ToF is a time based method for measurement of the WiFi device
location within a WiFi environment. The driver functionality provided
by this patch is the interface for communication with FW and receiving
location related updates from the FW. The interface provided by this
patch is via debugfs.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In the mvm driver, neither the old command nor the return value
are used, so remove them.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The current key offset assignment algorithm always uses the lowest
unused key offset, which will potentially lead to issues when the
firmware will change to take the key material for TX from the key
table rather than from the TX command.

In order to avoid those issues (and avoid forgetting about them)
change the key offset allocation algorithm now to avoid reusing key
offsets quickly.

The new algorithm always picks as the next offset the least recently
freed offset, i.e. the offset that has been unused for the longest
amount of time. This is implemented by having a generation counter
for each key offset that is incremented every time a key is deleted,
except for the one that's deleted, which is reset to zero. Thus the
highest counter is the key that's been unused longest.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

When introducing multiple RX queues, a single NAPI struct will not
be sufficient. Instead of trying to store multiple, simply change
the API to have the NAPI struct passed to the RX function. This of
course means that drivers using rx_irqsafe() cannot use NAPI, but
that seems a reasonable trade-off, particularly since only two of
all drivers are currently using it at all.

While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag
again since this code path cannot have a napi struct anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

After the new ciphers CCMP-256 and GCMP-128/256 were implemented,
wpa_supplicant could start negotiating them and use the software
implementation. This, however, breaks D3 behaviour in the driver
since it means that WoWLAN will not be possible.

To avoid breaking that feature, advertise only ciphers that the
hardware supports.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently, loading the firmware fails when it has higher API or CAPA
bits than the driver supports. That's an issue with integration.

At the same time, actually using api[0] and capa[0] will become
confusing when we also have api[1] and capa[1], and it's almost
certain that we'll mix up the bits and use the bits for api[1] with
api[0] by accident.

Avoid all this by translating the API/CAPA bits to the regular kernel
test_bit() format, and also providing wrapper functions. Also use the
__bitwise__ facility of sparse to check that we're testing the right
one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The regular and scheduled scan functions are very similar, so they can
be combined into one.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

We can only have one scan of each type running at the same time, so we
can remove one attribute in the UID information we save.  We had array
index, UID and type, but only UID (== array_index) and type are
necessary.  Refactor the code to use this simplified array.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Some LMAC specific functions had too generic names
(i.e. *_scan_offload_*) and were hard to distinguish from functions
that are really generic.  Rename these functions to *_lmac_scan_* in
to make it more consistent and easier to read.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The iwl_mvm_scan_offload_stop() function is used to stop LMAC regular
scan, stop LMAC scheduled scan and stop UMAC scheduled scans (but not
UMAC regular scans), making it very difficult to read.

Reorganize the scan stopping functions by creating separate functions
to stop regular and scheduled scans, separating the LMAC stopping part
of the code from the rest and renaming the offload_stop function to
iwl_mvm_lmac_scan_stop().
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The iwl_mvm_config_sched_scan_profiles() function is only used in
scan.c, so remove the declaration from mvm.h and make it static.
Signed-off-by: NLuciano Coelho <luciano.coelho@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add UMAC scan iteration complete notification. This notification can
be enabled by setting scan_iter_notif_enabled through debugfs.
Upon receiving this notification, print the list of channels that
have been scanned in this iteration. This is useful for debugging.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

commit b112889c ("iwlwifi: mvm: add Aux ROC request/response flow")
added aux ROC flow in addition to the existing ROC flow. While doing
it, it moved the ROC reference release to a common work item, which
is being called for both the ROC and aux ROC flows.

This resulted in invalid reference accounting, as no reference was
taken in case of aux ROC, while a reference was released on completion.

Fix it by adding a reference for the aux ROC as well, and release
only the relevant references on completion (according to the set bits).

While at it, convert cancel_work_sync() to flush_work(), in order
to make sure the references are being cleaned properly.

Fixes: b112889c ("iwlwifi: mvm: add Aux ROC request/response flow")
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The thermal throttling parameters were constant and hardcoded, not allowing
changes for different NIC families.
Change this so that the values are part of the NIC family configuration and
are not constant (so they can be changed dynamically in the future).
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Reviewed-by: NLuciano Coelho <luciano.coelho@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>