Most of the probe code is the same between all the different
clock controllers. Consolidate the code into a common.c file.
This makes changes to the common probe parts easier and reduces
chances for bugs.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

According to Documentation/kbuild/makefiles.txt these symbols
should be clk-qcom-y. Otherwise the build will fail if
CONFIG_COMMON_CLK_QCOM=m. Fix it.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a driver for the global clock controller found on MSM8660
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most multimedia device drivers
to probe and control their clocks.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a driver for the global clock controller found on MSM 8974
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a driver for the multimedia clock controller found on MSM
8960 based platforms. This should allow multimedia device drivers
to probe and control their clocks.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a driver for the global clock controller found on MSM8960
based platforms. This should allow most non-multimedia device
drivers to probe and control their clocks.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Reset controllers and clock controllers are combined into one IP
block on Qualcomm chipsets. Usually a reset signal is associated
with each clock branch but sometimes a reset signal is associated
with a handful of clocks. Either way the register interface is
the same; set a bit to assert a reset and clear a bit to deassert
a reset. Add support for these types of resets signals.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add support for the root clock generators on Qualcomm devices.
RCGs are highly customizable mux/divider/counter clocks that can
be used to generate almost any rate desired given some input
source that is faster than the desired rate.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add support for Qualcomm's PLLs (phase locked loops). This is
sufficient enough to be able to determine the rate the PLL is
running at. We can add rate setting support later when it's
needed.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a clock type that associates a regmap pointer and some
enable/disable bits with a clk_hw struct. This will be the struct
that a hw specific implementation wraps if it wants to use the
regmap helper functions.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>